diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile index 27ca1ca6e827..ab6a5c6ea5ee 100644 --- a/arch/arm/boot/dts/Makefile +++ b/arch/arm/boot/dts/Makefile @@ -1,4 +1,11 @@ # SPDX-License-Identifier: GPL-2.0 + +dtb-$(CONFIG_ARCH_BCM2835) += \ + bcm2708-rpi-b-rev1.dtb \ + bcm2708-rpi-cm.dtb \ + bcm2710-rpi-cm3.dtb \ + bcm2711-rpi-cm4.dtb + dtb-$(CONFIG_ARCH_ALPINE) += \ alpine-db.dtb dtb-$(CONFIG_MACH_ARTPEC6) += \ @@ -1499,3 +1506,13 @@ dtb-$(CONFIG_ARCH_ASPEED) += \ aspeed-bmc-portwell-neptune.dtb \ aspeed-bmc-quanta-q71l.dtb \ aspeed-bmc-supermicro-x11spi.dtb + +targets += dtbs dtbs_install +targets += $(dtb-y) + +subdir-y := overlays + +# Enable fixups to support overlays on BCM2835 platforms +ifeq ($(CONFIG_ARCH_BCM2835),y) + DTC_FLAGS += -@ +endif diff --git a/arch/arm/boot/dts/bcm2708-rpi-b-plus.dts b/arch/arm/boot/dts/bcm2708-rpi-b-plus.dts new file mode 100644 index 000000000000..e42cba84ab0e --- /dev/null +++ b/arch/arm/boot/dts/bcm2708-rpi-b-plus.dts @@ -0,0 +1,129 @@ +/dts-v1/; + +#include "bcm2708.dtsi" +#include "bcm2708-rpi.dtsi" +#include "bcm283x-rpi-smsc9514.dtsi" +#include "bcm283x-rpi-csi1-2lane.dtsi" +#include "bcm283x-rpi-i2c0mux_0_28.dtsi" +#include "bcm283x-rpi-cam1-regulator.dtsi" + +/ { + compatible = "raspberrypi,model-b-plus", "brcm,bcm2835"; + model = "Raspberry Pi Model B+"; +}; + +&gpio { + spi0_pins: spi0_pins { + brcm,pins = <9 10 11>; + brcm,function = <4>; /* alt0 */ + }; + + spi0_cs_pins: spi0_cs_pins { + brcm,pins = <8 7>; + brcm,function = <1>; /* output */ + }; + + i2c0_pins: i2c0 { + brcm,pins = <0 1>; + brcm,function = <4>; + }; + + i2c1_pins: i2c1 { + brcm,pins = <2 3>; + brcm,function = <4>; + }; + + i2s_pins: i2s { + brcm,pins = <18 19 20 21>; + brcm,function = <4>; /* alt0 */ + }; + + audio_pins: audio_pins { + brcm,pins = <40 45>; + brcm,function = <4>; + }; +}; + +&uart0 { + status = "okay"; +}; + +&spi0 { + pinctrl-names = "default"; + pinctrl-0 = <&spi0_pins &spi0_cs_pins>; + cs-gpios = <&gpio 8 1>, <&gpio 7 1>; + + spidev0: spidev@0{ + compatible = "spidev"; + reg = <0>; /* CE0 */ + #address-cells = <1>; + #size-cells = <0>; + spi-max-frequency = <125000000>; + }; + + spidev1: spidev@1{ + compatible = "spidev"; + reg = <1>; /* CE1 */ + #address-cells = <1>; + #size-cells = <0>; + spi-max-frequency = <125000000>; + }; +}; + +&i2c0if { + clock-frequency = <100000>; +}; + +&i2c1 { + pinctrl-names = "default"; + pinctrl-0 = <&i2c1_pins>; + clock-frequency = <100000>; +}; + +&i2c2 { + clock-frequency = <100000>; +}; + +&i2s { + pinctrl-names = "default"; + pinctrl-0 = <&i2s_pins>; +}; + +&leds { + act_led: led-act { + label = "led0"; + linux,default-trigger = "mmc0"; + gpios = <&gpio 47 0>; + }; + + pwr_led: led-pwr { + label = "led1"; + linux,default-trigger = "input"; + gpios = <&gpio 35 0>; + }; +}; + +&hdmi { + hpd-gpios = <&gpio 46 GPIO_ACTIVE_LOW>; +}; + +&audio { + pinctrl-names = "default"; + pinctrl-0 = <&audio_pins>; +}; + +&cam1_reg { + gpio = <&gpio 41 GPIO_ACTIVE_HIGH>; +}; + +/ { + __overrides__ { + act_led_gpio = <&act_led>,"gpios:4"; + act_led_activelow = <&act_led>,"gpios:8"; + act_led_trigger = <&act_led>,"linux,default-trigger"; + + pwr_led_gpio = <&pwr_led>,"gpios:4"; + pwr_led_activelow = <&pwr_led>,"gpios:8"; + pwr_led_trigger = <&pwr_led>,"linux,default-trigger"; + }; +}; diff --git a/arch/arm/boot/dts/bcm2708-rpi-b-rev1.dts b/arch/arm/boot/dts/bcm2708-rpi-b-rev1.dts new file mode 100644 index 000000000000..4ea1e68f5e29 --- /dev/null +++ b/arch/arm/boot/dts/bcm2708-rpi-b-rev1.dts @@ -0,0 +1,132 @@ +/dts-v1/; + +#include "bcm2708.dtsi" +#include "bcm2708-rpi.dtsi" +#include "bcm283x-rpi-smsc9512.dtsi" +#include "bcm283x-rpi-csi1-2lane.dtsi" +#include "bcm283x-rpi-cam1-regulator.dtsi" + +/ { + compatible = "raspberrypi,model-b", "brcm,bcm2835"; + model = "Raspberry Pi Model B"; +}; + +&gpio { + spi0_pins: spi0_pins { + brcm,pins = <9 10 11>; + brcm,function = <4>; /* alt0 */ + }; + + spi0_cs_pins: spi0_cs_pins { + brcm,pins = <8 7>; + brcm,function = <1>; /* output */ + }; + + i2c0_pins: i2c0 { + brcm,pins = <0 1>; + brcm,function = <4>; + }; + + i2c1_pins: i2c1 { + brcm,pins = <2 3>; + brcm,function = <4>; + }; + + i2s_pins: i2s { + brcm,pins = <28 29 30 31>; + brcm,function = <6>; /* alt2 */ + }; + + audio_pins: audio_pins { + brcm,pins = <40 45>; + brcm,function = <4>; + }; +}; + +&uart0 { + status = "okay"; +}; + +&spi0 { + pinctrl-names = "default"; + pinctrl-0 = <&spi0_pins &spi0_cs_pins>; + cs-gpios = <&gpio 8 1>, <&gpio 7 1>; + + spidev0: spidev@0{ + compatible = "spidev"; + reg = <0>; /* CE0 */ + #address-cells = <1>; + #size-cells = <0>; + spi-max-frequency = <125000000>; + }; + + spidev1: spidev@1{ + compatible = "spidev"; + reg = <1>; /* CE1 */ + #address-cells = <1>; + #size-cells = <0>; + spi-max-frequency = <125000000>; + }; +}; + +/delete-node/ &i2c0mux; + +i2c0: &i2c0if { + pinctrl-names = "default"; + pinctrl-0 = <&i2c0_pins>; + clock-frequency = <100000>; +}; + +i2c_csi_dsi: &i2c1 { + pinctrl-names = "default"; + pinctrl-0 = <&i2c1_pins>; + clock-frequency = <100000>; +}; + +/ { + aliases { + i2c0 = &i2c0; + }; + + __overrides__ { + i2c0 = <&i2c0>, "status"; + }; +}; + +&i2c2 { + clock-frequency = <100000>; +}; + +&i2s { + pinctrl-names = "default"; + pinctrl-0 = <&i2s_pins>; +}; + +&leds { + act_led: led-act { + label = "led0"; + linux,default-trigger = "mmc0"; + gpios = <&gpio 16 1>; + }; +}; + +&hdmi { + hpd-gpios = <&gpio 46 GPIO_ACTIVE_HIGH>; +}; + +&audio { + pinctrl-names = "default"; + pinctrl-0 = <&audio_pins>; +}; + +&cam1_reg { + gpio = <&gpio 27 GPIO_ACTIVE_HIGH>; +}; + +/ { + __overrides__ { + act_led_gpio = <&act_led>,"gpios:4"; + act_led_activelow = <&act_led>,"gpios:8"; + act_led_trigger = <&act_led>,"linux,default-trigger"; + }; +}; diff --git a/arch/arm/boot/dts/bcm2708-rpi-b.dts b/arch/arm/boot/dts/bcm2708-rpi-b.dts new file mode 100644 index 000000000000..a152c1c8e648 --- /dev/null +++ b/arch/arm/boot/dts/bcm2708-rpi-b.dts @@ -0,0 +1,119 @@ +/dts-v1/; + +#include "bcm2708.dtsi" +#include "bcm2708-rpi.dtsi" +#include "bcm283x-rpi-smsc9512.dtsi" +#include "bcm283x-rpi-csi1-2lane.dtsi" +#include "bcm283x-rpi-i2c0mux_0_28.dtsi" +#include "bcm283x-rpi-cam1-regulator.dtsi" + +/ { + compatible = "raspberrypi,model-b", "brcm,bcm2835"; + model = "Raspberry Pi Model B"; +}; + +&gpio { + spi0_pins: spi0_pins { + brcm,pins = <9 10 11>; + brcm,function = <4>; /* alt0 */ + }; + + spi0_cs_pins: spi0_cs_pins { + brcm,pins = <8 7>; + brcm,function = <1>; /* output */ + }; + + i2c0_pins: i2c0 { + brcm,pins = <0 1>; + brcm,function = <4>; + }; + + i2c1_pins: i2c1 { + brcm,pins = <2 3>; + brcm,function = <4>; + }; + + i2s_pins: i2s { + brcm,pins = <28 29 30 31>; + brcm,function = <6>; /* alt2 */ + }; + + audio_pins: audio_pins { + brcm,pins = <40 45>; + brcm,function = <4>; + }; +}; + +&uart0 { + status = "okay"; +}; + +&spi0 { + pinctrl-names = "default"; + pinctrl-0 = <&spi0_pins &spi0_cs_pins>; + cs-gpios = <&gpio 8 1>, <&gpio 7 1>; + + spidev0: spidev@0{ + compatible = "spidev"; + reg = <0>; /* CE0 */ + #address-cells = <1>; + #size-cells = <0>; + spi-max-frequency = <125000000>; + }; + + spidev1: spidev@1{ + compatible = "spidev"; + reg = <1>; /* CE1 */ + #address-cells = <1>; + #size-cells = <0>; + spi-max-frequency = <125000000>; + }; +}; + +&i2c0if { + clock-frequency = <100000>; +}; + +&i2c1 { + pinctrl-names = "default"; + pinctrl-0 = <&i2c1_pins>; + clock-frequency = <100000>; +}; + +&i2c2 { + clock-frequency = <100000>; +}; + +&i2s { + pinctrl-names = "default"; + pinctrl-0 = <&i2s_pins>; +}; + +&leds { + act_led: led-act { + label = "led0"; + linux,default-trigger = "mmc0"; + gpios = <&gpio 16 1>; + }; +}; + +&hdmi { + hpd-gpios = <&gpio 46 GPIO_ACTIVE_HIGH>; +}; + +&audio { + pinctrl-names = "default"; + pinctrl-0 = <&audio_pins>; +}; + +&cam1_reg { + gpio = <&gpio 21 GPIO_ACTIVE_HIGH>; +}; + +/ { + __overrides__ { + act_led_gpio = <&act_led>,"gpios:4"; + act_led_activelow = <&act_led>,"gpios:8"; + act_led_trigger = <&act_led>,"linux,default-trigger"; + }; +}; diff --git a/arch/arm/boot/dts/bcm2708-rpi-bt.dtsi b/arch/arm/boot/dts/bcm2708-rpi-bt.dtsi new file mode 100644 index 000000000000..a18f80af97d3 --- /dev/null +++ b/arch/arm/boot/dts/bcm2708-rpi-bt.dtsi @@ -0,0 +1,26 @@ +// SPDX-License-Identifier: GPL-2.0 + +&uart0 { + bt: bluetooth { + compatible = "brcm,bcm43438-bt"; + max-speed = <3000000>; + shutdown-gpios = <&gpio 45 GPIO_ACTIVE_HIGH>; + status = "disabled"; + }; +}; + +&uart1 { + minibt: bluetooth { + compatible = "brcm,bcm43438-bt"; + max-speed = <460800>; + shutdown-gpios = <&gpio 45 GPIO_ACTIVE_HIGH>; + status = "disabled"; + }; +}; + +/ { + __overrides__ { + krnbt = <&bt>,"status"; + krnbt_baudrate = <&bt>,"max-speed:0"; + }; +}; diff --git a/arch/arm/boot/dts/bcm2708-rpi-cm.dts b/arch/arm/boot/dts/bcm2708-rpi-cm.dts new file mode 100644 index 000000000000..f61e3418425a --- /dev/null +++ b/arch/arm/boot/dts/bcm2708-rpi-cm.dts @@ -0,0 +1,112 @@ +/dts-v1/; + +#include "bcm2708-rpi-cm.dtsi" +#include "bcm283x-rpi-csi0-2lane.dtsi" +#include "bcm283x-rpi-csi1-4lane.dtsi" +#include "bcm283x-rpi-i2c0mux_0_28.dtsi" + +/ { + compatible = "raspberrypi,compute-module", "brcm,bcm2835"; + model = "Raspberry Pi Compute Module"; + + cam1_reg: cam1_reg { + compatible = "regulator-fixed"; + regulator-name = "cam1-regulator"; + gpio = <&gpio 2 GPIO_ACTIVE_HIGH>; + enable-active-high; + status = "disabled"; + }; + cam0_reg: cam0_reg { + compatible = "regulator-fixed"; + regulator-name = "cam0-regulator"; + gpio = <&gpio 30 GPIO_ACTIVE_HIGH>; + enable-active-high; + status = "disabled"; + }; +}; + +&uart0 { + status = "okay"; +}; + +&gpio { + spi0_pins: spi0_pins { + brcm,pins = <9 10 11>; + brcm,function = <4>; /* alt0 */ + }; + + spi0_cs_pins: spi0_cs_pins { + brcm,pins = <8 7>; + brcm,function = <1>; /* output */ + }; + + i2c0_pins: i2c0 { + brcm,pins = <0 1>; + brcm,function = <4>; + }; + + i2c1_pins: i2c1 { + brcm,pins = <2 3>; + brcm,function = <4>; + }; + + i2s_pins: i2s { + brcm,pins = <18 19 20 21>; + brcm,function = <4>; /* alt0 */ + }; + + audio_pins: audio_pins { + brcm,pins; + brcm,function; + }; +}; + +&spi0 { + pinctrl-names = "default"; + pinctrl-0 = <&spi0_pins &spi0_cs_pins>; + cs-gpios = <&gpio 8 1>, <&gpio 7 1>; + + spidev0: spidev@0{ + compatible = "spidev"; + reg = <0>; /* CE0 */ + #address-cells = <1>; + #size-cells = <0>; + spi-max-frequency = <125000000>; + }; + + spidev1: spidev@1{ + compatible = "spidev"; + reg = <1>; /* CE1 */ + #address-cells = <1>; + #size-cells = <0>; + spi-max-frequency = <125000000>; + }; +}; + +&i2c0if { + clock-frequency = <100000>; +}; + +&i2c1 { + pinctrl-names = "default"; + pinctrl-0 = <&i2c1_pins>; + clock-frequency = <100000>; +}; + +&i2c2 { + clock-frequency = <100000>; +}; + +&i2s { + pinctrl-names = "default"; + pinctrl-0 = <&i2s_pins>; +}; + +&audio { + pinctrl-names = "default"; + pinctrl-0 = <&audio_pins>; +}; + +&hdmi { + hpd-gpios = <&gpio 46 GPIO_ACTIVE_HIGH>; +}; diff --git a/arch/arm/boot/dts/bcm2708-rpi-cm.dtsi b/arch/arm/boot/dts/bcm2708-rpi-cm.dtsi new file mode 100644 index 000000000000..d5572b2d2103 --- /dev/null +++ b/arch/arm/boot/dts/bcm2708-rpi-cm.dtsi @@ -0,0 +1,18 @@ +#include "bcm2708.dtsi" +#include "bcm2708-rpi.dtsi" + +&leds { + act_led: led-act { + label = "led0"; + linux,default-trigger = "mmc0"; + gpios = <&gpio 47 0>; + }; +}; + +/ { + __overrides__ { + act_led_gpio = <&act_led>,"gpios:4"; + act_led_activelow = <&act_led>,"gpios:8"; + act_led_trigger = <&act_led>,"linux,default-trigger"; + }; +}; diff --git a/arch/arm/boot/dts/bcm2708-rpi-zero-w.dts b/arch/arm/boot/dts/bcm2708-rpi-zero-w.dts new file mode 100644 index 000000000000..75a5b41514f9 --- /dev/null +++ b/arch/arm/boot/dts/bcm2708-rpi-zero-w.dts @@ -0,0 +1,169 @@ +/dts-v1/; + +#include "bcm2708.dtsi" +#include "bcm2708-rpi.dtsi" +#include "bcm283x-rpi-csi1-2lane.dtsi" +#include "bcm283x-rpi-i2c0mux_0_28.dtsi" +#include "bcm2708-rpi-bt.dtsi" +#include "bcm283x-rpi-cam1-regulator.dtsi" + +/ { + compatible = "raspberrypi,model-zero-w", "brcm,bcm2835"; + model = "Raspberry Pi Zero W"; + + chosen { + bootargs = "coherent_pool=1M 8250.nr_uarts=1 snd_bcm2835.enable_compat_alsa=0 snd_bcm2835.enable_hdmi=1"; + }; + + aliases { + serial0 = &uart1; + serial1 = &uart0; + mmc1 = &mmcnr; + }; +}; + +&gpio { + spi0_pins: spi0_pins { + brcm,pins = <9 10 11>; + brcm,function = <4>; /* alt0 */ + }; + + spi0_cs_pins: spi0_cs_pins { + brcm,pins = <8 7>; + brcm,function = <1>; /* output */ + }; + + i2c0_pins: i2c0 { + brcm,pins = <0 1>; + brcm,function = <4>; + }; + + i2c1_pins: i2c1 { + brcm,pins = <2 3>; + brcm,function = <4>; + }; + + i2s_pins: i2s { + brcm,pins = <18 19 20 21>; + brcm,function = <4>; /* alt0 */ + }; + + sdio_pins: sdio_pins { + brcm,pins = <34 35 36 37 38 39>; + brcm,function = <7>; /* ALT3 = SD1 */ + brcm,pull = <0 2 2 2 2 2>; + }; + + bt_pins: bt_pins { + brcm,pins = <43>; + brcm,function = <4>; /* alt0:GPCLK2 */ + brcm,pull = <0>; /* none */ + }; + + uart0_pins: uart0_pins { + brcm,pins = <30 31 32 33>; + brcm,function = <7>; /* alt3=UART0 */ + brcm,pull = <2 0 0 2>; /* up none none up */ + }; + + uart1_pins: uart1_pins { + brcm,pins; + brcm,function; + brcm,pull; + }; + + audio_pins: audio_pins { + brcm,pins = <>; + brcm,function = <>; + }; +}; + +&mmcnr { + pinctrl-names = "default"; + pinctrl-0 = <&sdio_pins>; + bus-width = <4>; + status = "okay"; +}; + +&uart0 { + pinctrl-names = "default"; + pinctrl-0 = <&uart0_pins &bt_pins>; + status = "okay"; +}; + +&uart1 { + pinctrl-names = "default"; + pinctrl-0 = <&uart1_pins>; + status = "okay"; +}; + +&spi0 { + pinctrl-names = "default"; + pinctrl-0 = <&spi0_pins &spi0_cs_pins>; + cs-gpios = <&gpio 8 1>, <&gpio 7 1>; + + spidev0: spidev@0{ + compatible = "spidev"; + reg = <0>; /* CE0 */ + #address-cells = <1>; + #size-cells = <0>; + spi-max-frequency = <125000000>; + }; + + spidev1: spidev@1{ + compatible = "spidev"; + reg = <1>; /* CE1 */ + #address-cells = <1>; + #size-cells = <0>; + spi-max-frequency = <125000000>; + }; +}; + +&i2c0if { + clock-frequency = <100000>; +}; + +&i2c1 { + pinctrl-names = "default"; + pinctrl-0 = <&i2c1_pins>; + clock-frequency = <100000>; +}; + +&i2c2 { + clock-frequency = <100000>; +}; + +&i2s { + pinctrl-names = "default"; + pinctrl-0 = <&i2s_pins>; +}; + +&leds { + act_led: led-act { + label = "led0"; + linux,default-trigger = "actpwr"; + gpios = <&gpio 47 GPIO_ACTIVE_LOW>; + }; +}; + +&hdmi { + hpd-gpios = <&gpio 46 GPIO_ACTIVE_LOW>; +}; + +&audio { + pinctrl-names = "default"; + pinctrl-0 = <&audio_pins>; + brcm,disable-headphones = <1>; +}; + +&cam1_reg { + gpio = <&gpio 44 GPIO_ACTIVE_HIGH>; +}; + +/ { + __overrides__ { + act_led_gpio = <&act_led>,"gpios:4"; + act_led_activelow = <&act_led>,"gpios:8"; + act_led_trigger = <&act_led>,"linux,default-trigger"; + }; +}; diff --git a/arch/arm/boot/dts/bcm2708-rpi-zero.dts b/arch/arm/boot/dts/bcm2708-rpi-zero.dts new file mode 100644 index 000000000000..84591bd7d423 --- /dev/null +++ b/arch/arm/boot/dts/bcm2708-rpi-zero.dts @@ -0,0 +1,123 @@ +/dts-v1/; + +#include "bcm2708.dtsi" +#include "bcm2708-rpi.dtsi" +#include "bcm283x-rpi-csi1-2lane.dtsi" +#include "bcm283x-rpi-i2c0mux_0_28.dtsi" +#include "bcm283x-rpi-cam1-regulator.dtsi" + +/ { + compatible = "raspberrypi,model-zero", "brcm,bcm2835"; + model = "Raspberry Pi Zero"; + + chosen { + bootargs = "coherent_pool=1M snd_bcm2835.enable_compat_alsa=0 snd_bcm2835.enable_hdmi=1"; + }; +}; + +&gpio { + spi0_pins: spi0_pins { + brcm,pins = <9 10 11>; + brcm,function = <4>; /* alt0 */ + }; + + spi0_cs_pins: spi0_cs_pins { + brcm,pins = <8 7>; + brcm,function = <1>; /* output */ + }; + + i2c0_pins: i2c0 { + brcm,pins = <0 1>; + brcm,function = <4>; + }; + + i2c1_pins: i2c1 { + brcm,pins = <2 3>; + brcm,function = <4>; + }; + + i2s_pins: i2s { + brcm,pins = <18 19 20 21>; + brcm,function = <4>; /* alt0 */ + }; + + audio_pins: audio_pins { + brcm,pins = <>; + brcm,function = <>; + }; +}; + +&uart0 { + status = "okay"; +}; + +&spi0 { + pinctrl-names = "default"; + pinctrl-0 = <&spi0_pins &spi0_cs_pins>; + cs-gpios = <&gpio 8 1>, <&gpio 7 1>; + + spidev0: spidev@0{ + compatible = "spidev"; + reg = <0>; /* CE0 */ + #address-cells = <1>; + #size-cells = <0>; + spi-max-frequency = <125000000>; + }; + + spidev1: spidev@1{ + compatible = "spidev"; + reg = <1>; /* CE1 */ + #address-cells = <1>; + #size-cells = <0>; + spi-max-frequency = <125000000>; + }; +}; + +&i2c0if { + clock-frequency = <100000>; +}; + +&i2c1 { + pinctrl-names = "default"; + pinctrl-0 = <&i2c1_pins>; + clock-frequency = <100000>; +}; + +&i2c2 { + clock-frequency = <100000>; +}; + +&i2s { + pinctrl-names = "default"; + pinctrl-0 = <&i2s_pins>; +}; + +&leds { + act_led: led-act { + label = "led0"; + linux,default-trigger = "actpwr"; + gpios = <&gpio 47 GPIO_ACTIVE_LOW>; + }; +}; + +&hdmi { + hpd-gpios = <&gpio 46 GPIO_ACTIVE_LOW>; +}; + +&audio { + pinctrl-names = "default"; + pinctrl-0 = <&audio_pins>; + brcm,disable-headphones = <1>; +}; + +&cam1_reg { + gpio = <&gpio 41 GPIO_ACTIVE_HIGH>; +}; + +/ { + __overrides__ { + act_led_gpio = <&act_led>,"gpios:4"; + act_led_activelow = <&act_led>,"gpios:8"; + act_led_trigger = <&act_led>,"linux,default-trigger"; + }; +}; diff --git a/arch/arm/boot/dts/bcm2708-rpi.dtsi b/arch/arm/boot/dts/bcm2708-rpi.dtsi new file mode 100644 index 000000000000..e2458b15d64a --- /dev/null +++ b/arch/arm/boot/dts/bcm2708-rpi.dtsi @@ -0,0 +1,36 @@ +/* Downstream modifications common to bcm2835, bcm2836, bcm2837 */ + +#include "bcm2835-rpi.dtsi" +#include "bcm270x-rpi.dtsi" + +/ { + memory@0 { + device_type = "memory"; + reg = <0x0 0x0>; + }; + + aliases { + i2c2 = &i2c2; + }; + + __overrides__ { + i2c2_iknowwhatimdoing = <&i2c2>,"status"; + i2c2_baudrate = <&i2c2>,"clock-frequency:0"; + sd_poll_once = <&sdhost>,"non-removable?"; + }; +}; + +&sdhost { + pinctrl-names = "default"; + pinctrl-0 = <&sdhost_gpio48>; + status = "okay"; +}; + +&hdmi { + power-domains = <&power RPI_POWER_DOMAIN_HDMI>; + status = "disabled"; +}; + +&i2c2 { + status = "disabled"; +}; diff --git a/arch/arm/boot/dts/bcm2708.dtsi b/arch/arm/boot/dts/bcm2708.dtsi new file mode 100644 index 000000000000..36ec4989403f --- /dev/null +++ b/arch/arm/boot/dts/bcm2708.dtsi @@ -0,0 +1,12 @@ +#include "bcm2835.dtsi" +#include "bcm270x.dtsi" + +/ { + __overrides__ { + arm_freq; + }; +}; + +&vc4 { + status = "disabled"; +}; diff --git a/arch/arm/boot/dts/bcm2709-rpi-2-b.dts b/arch/arm/boot/dts/bcm2709-rpi-2-b.dts new file mode 100644 index 000000000000..e1381d2b3a2c --- /dev/null +++ b/arch/arm/boot/dts/bcm2709-rpi-2-b.dts @@ -0,0 +1,129 @@ +/dts-v1/; + +#include "bcm2709.dtsi" +#include "bcm2709-rpi.dtsi" +#include "bcm283x-rpi-smsc9514.dtsi" +#include "bcm283x-rpi-csi1-2lane.dtsi" +#include "bcm283x-rpi-i2c0mux_0_28.dtsi" +#include "bcm283x-rpi-cam1-regulator.dtsi" + +/ { + compatible = "raspberrypi,2-model-b", "brcm,bcm2836"; + model = "Raspberry Pi 2 Model B"; +}; + +&gpio { + spi0_pins: spi0_pins { + brcm,pins = <9 10 11>; + brcm,function = <4>; /* alt0 */ + }; + + spi0_cs_pins: spi0_cs_pins { + brcm,pins = <8 7>; + brcm,function = <1>; /* output */ + }; + + i2c0_pins: i2c0 { + brcm,pins = <0 1>; + brcm,function = <4>; + }; + + i2c1_pins: i2c1 { + brcm,pins = <2 3>; + brcm,function = <4>; + }; + + i2s_pins: i2s { + brcm,pins = <18 19 20 21>; + brcm,function = <4>; /* alt0 */ + }; + + audio_pins: audio_pins { + brcm,pins = <40 45>; + brcm,function = <4>; + }; +}; + +&uart0 { + status = "okay"; +}; + +&spi0 { + pinctrl-names = "default"; + pinctrl-0 = <&spi0_pins &spi0_cs_pins>; + cs-gpios = <&gpio 8 1>, <&gpio 7 1>; + + spidev0: spidev@0{ + compatible = "spidev"; + reg = <0>; /* CE0 */ + #address-cells = <1>; + #size-cells = <0>; + spi-max-frequency = <125000000>; + }; + + spidev1: spidev@1{ + compatible = "spidev"; + reg = <1>; /* CE1 */ + #address-cells = <1>; + #size-cells = <0>; + spi-max-frequency = <125000000>; + }; +}; + +&i2c0if { + clock-frequency = <100000>; +}; + +&i2c1 { + pinctrl-names = "default"; + pinctrl-0 = <&i2c1_pins>; + clock-frequency = <100000>; +}; + +&i2c2 { + clock-frequency = <100000>; +}; + +&i2s { + pinctrl-names = "default"; + pinctrl-0 = <&i2s_pins>; +}; + +&leds { + act_led: led-act { + label = "led0"; + linux,default-trigger = "mmc0"; + gpios = <&gpio 47 0>; + }; + + pwr_led: led-pwr { + label = "led1"; + linux,default-trigger = "input"; + gpios = <&gpio 35 0>; + }; +}; + +&hdmi { + hpd-gpios = <&gpio 46 GPIO_ACTIVE_LOW>; +}; + +&audio { + pinctrl-names = "default"; + pinctrl-0 = <&audio_pins>; +}; + +&cam1_reg { + gpio = <&gpio 41 GPIO_ACTIVE_HIGH>; +}; + +/ { + __overrides__ { + act_led_gpio = <&act_led>,"gpios:4"; + act_led_activelow = <&act_led>,"gpios:8"; + act_led_trigger = <&act_led>,"linux,default-trigger"; + + pwr_led_gpio = <&pwr_led>,"gpios:4"; + pwr_led_activelow = <&pwr_led>,"gpios:8"; + pwr_led_trigger = <&pwr_led>,"linux,default-trigger"; + }; +}; diff --git a/arch/arm/boot/dts/bcm2709-rpi.dtsi b/arch/arm/boot/dts/bcm2709-rpi.dtsi new file mode 100644 index 000000000000..babfa41cd9f7 --- /dev/null +++ b/arch/arm/boot/dts/bcm2709-rpi.dtsi @@ -0,0 +1,5 @@ +#include "bcm2708-rpi.dtsi" + +&vchiq { + compatible = "brcm,bcm2836-vchiq", "brcm,bcm2835-vchiq"; +}; diff --git a/arch/arm/boot/dts/bcm2709.dtsi b/arch/arm/boot/dts/bcm2709.dtsi new file mode 100644 index 000000000000..68eafc1b281a --- /dev/null +++ b/arch/arm/boot/dts/bcm2709.dtsi @@ -0,0 +1,22 @@ +#include "bcm2836.dtsi" +#include "bcm270x.dtsi" + +/ { + soc { + ranges = <0x7e000000 0x3f000000 0x01000000>, + <0x40000000 0x40000000 0x00040000>; + + /delete-node/ timer@7e003000; + }; + + __overrides__ { + arm_freq = <&v7_cpu0>, "clock-frequency:0", + <&v7_cpu1>, "clock-frequency:0", + <&v7_cpu2>, "clock-frequency:0", + <&v7_cpu3>, "clock-frequency:0"; + }; +}; + +&vc4 { + status = "disabled"; +}; diff --git a/arch/arm/boot/dts/bcm270x-rpi.dtsi b/arch/arm/boot/dts/bcm270x-rpi.dtsi new file mode 100644 index 000000000000..68a7e1c09db1 --- /dev/null +++ b/arch/arm/boot/dts/bcm270x-rpi.dtsi @@ -0,0 +1,154 @@ +/* Downstream modifications to bcm2835-rpi.dtsi */ + +/ { + aliases { + audio = &audio; + aux = &aux; + sound = &sound; + soc = &soc; + dma = &dma; + intc = &intc; + watchdog = &watchdog; + random = &random; + mailbox = &mailbox; + gpio = &gpio; + uart0 = &uart0; + uart1 = &uart1; + sdhost = &sdhost; + mmc = &mmc; + mmc1 = &mmc; + mmc0 = &sdhost; + i2s = &i2s; + i2c0 = &i2c0; + i2c1 = &i2c1; + i2c10 = &i2c_csi_dsi; + spi0 = &spi0; + spi1 = &spi1; + spi2 = &spi2; + usb = &usb; + leds = &leds; + fb = &fb; + thermal = &thermal; + axiperf = &axiperf; + }; + + /* Define these notional regulators for use by overlays */ + vdd_3v3_reg: fixedregulator_3v3 { + compatible = "regulator-fixed"; + regulator-always-on; + regulator-max-microvolt = <3300000>; + regulator-min-microvolt = <3300000>; + regulator-name = "3v3"; + }; + + vdd_5v0_reg: fixedregulator_5v0 { + compatible = "regulator-fixed"; + regulator-always-on; + regulator-max-microvolt = <5000000>; + regulator-min-microvolt = <5000000>; + regulator-name = "5v0"; + }; + + leds: leds { + compatible = "gpio-leds"; + }; + + soc { + gpiomem { + compatible = "brcm,bcm2835-gpiomem"; + reg = <0x7e200000 0x1000>; + }; + + fb: fb { + compatible = "brcm,bcm2708-fb"; + firmware = <&firmware>; + status = "okay"; + }; + + vcsm: vcsm { + compatible = "raspberrypi,bcm2835-vcsm"; + firmware = <&firmware>; + status = "okay"; + }; + + /* External sound card */ + sound: sound { + status = "disabled"; + }; + }; + + __overrides__ { + cache_line_size; + + uart0 = <&uart0>,"status"; + uart1 = <&uart1>,"status"; + i2s = <&i2s>,"status"; + spi = <&spi0>,"status"; + i2c0 = <&i2c0if>,"status",<&i2c0mux>,"status"; + i2c1 = <&i2c1>,"status"; + i2c0_baudrate = <&i2c0if>,"clock-frequency:0"; + i2c1_baudrate = <&i2c1>,"clock-frequency:0"; + + audio = <&audio>,"status"; + watchdog = <&watchdog>,"status"; + random = <&random>,"status"; + sd_overclock = <&sdhost>,"brcm,overclock-50:0"; + sd_force_pio = <&sdhost>,"brcm,force-pio?"; + sd_pio_limit = <&sdhost>,"brcm,pio-limit:0"; + sd_debug = <&sdhost>,"brcm,debug"; + sdio_overclock = <&mmc>,"brcm,overclock-50:0", + <&mmcnr>,"brcm,overclock-50:0"; + axiperf = <&axiperf>,"status"; + }; +}; + +&uart0 { + skip-init; +}; + +&uart1 { + skip-init; +}; + +&txp { + status = "disabled"; +}; + +&i2c0if { + status = "disabled"; +}; + +&i2c0mux { + status = "disabled"; +}; + +&i2c1 { + status = "disabled"; +}; + +&clocks { + firmware = <&firmware>; +}; + +&sdhci { + pinctrl-names = "default"; + pinctrl-0 = <&emmc_gpio48>; + bus-width = <4>; +}; + +&cpu_thermal { + /delete-node/ trips; +}; + +&vec { + status = "disabled"; +}; + +&vchiq { + /* Onboard audio */ + audio: bcm2835_audio { + compatible = "brcm,bcm2835-audio"; + brcm,pwm-channels = <8>; + status = "disabled"; + }; +}; diff --git a/arch/arm/boot/dts/bcm270x.dtsi b/arch/arm/boot/dts/bcm270x.dtsi new file mode 100644 index 000000000000..badcf341ecd2 --- /dev/null +++ b/arch/arm/boot/dts/bcm270x.dtsi @@ -0,0 +1,217 @@ +/* Downstream bcm283x.dtsi diff */ +#include + +/ { + chosen { + bootargs = "coherent_pool=1M snd_bcm2835.enable_compat_alsa=0 snd_bcm2835.enable_hdmi=1"; + /delete-property/ stdout-path; + }; + + soc: soc { + + watchdog: watchdog@7e100000 { + /* Add label */ + }; + + random: rng@7e104000 { + /* Add label */ + }; + + spi0: spi@7e204000 { + /* Add label */ + }; + +#ifndef BCM2711 + pixelvalve0: pixelvalve@7e206000 { + /* Add label */ + status = "disabled"; + }; + + pixelvalve1: pixelvalve@7e207000 { + /* Add label */ + status = "disabled"; + }; +#endif + + /delete-node/ mmc@7e300000; + + sdhci: mmc: mmc@7e300000 { + compatible = "brcm,bcm2835-mmc", "brcm,bcm2835-sdhci"; + reg = <0x7e300000 0x100>; + interrupts = <2 30>; + clocks = <&clocks BCM2835_CLOCK_EMMC>; + dmas = <&dma 11>; + dma-names = "rx-tx"; + brcm,overclock-50 = <0>; + status = "disabled"; + }; + + /* A clone of mmc but with non-removable set */ + mmcnr: mmcnr@7e300000 { + compatible = "brcm,bcm2835-mmc", "brcm,bcm2835-sdhci"; + reg = <0x7e300000 0x100>; + interrupts = <2 30>; + clocks = <&clocks BCM2835_CLOCK_EMMC>; + dmas = <&dma 11>; + dma-names = "rx-tx"; + brcm,overclock-50 = <0>; + non-removable; + status = "disabled"; + }; + + hvs: hvs@7e400000 { + /* Add label */ + status = "disabled"; + }; + + firmwarekms: firmwarekms@7e600000 { + compatible = "raspberrypi,rpi-firmware-kms"; + /* SMI interrupt reg */ + reg = <0x7e600000 0x100>; + interrupts = <2 16>; + brcm,firmware = <&firmware>; + status = "disabled"; + }; + + smi: smi@7e600000 { + compatible = "brcm,bcm2835-smi"; + reg = <0x7e600000 0x100>; + interrupts = <2 16>; + clocks = <&clocks BCM2835_CLOCK_SMI>; + assigned-clocks = <&clocks BCM2835_CLOCK_SMI>; + assigned-clock-rates = <125000000>; + dmas = <&dma 4>; + dma-names = "rx-tx"; + status = "disabled"; + }; + + csi0: csi@7e800000 { + compatible = "brcm,bcm2835-unicam"; + reg = <0x7e800000 0x800>, + <0x7e802000 0x4>; + interrupts = <2 6>; + clocks = <&clocks BCM2835_CLOCK_CAM0>, + <&firmware_clocks 4>; + clock-names = "lp", "vpu"; + power-domains = <&power RPI_POWER_DOMAIN_UNICAM0>; + #address-cells = <1>; + #size-cells = <0>; + #clock-cells = <1>; + status = "disabled"; + }; + + csi1: csi@7e801000 { + compatible = "brcm,bcm2835-unicam"; + reg = <0x7e801000 0x800>, + <0x7e802004 0x4>; + interrupts = <2 7>; + clocks = <&clocks BCM2835_CLOCK_CAM1>, + <&firmware_clocks 4>; + clock-names = "lp", "vpu"; + power-domains = <&power RPI_POWER_DOMAIN_UNICAM1>; + #address-cells = <1>; + #size-cells = <0>; + #clock-cells = <1>; + status = "disabled"; + }; + +#ifndef BCM2711 + pixelvalve2: pixelvalve@7e807000 { + /* Add label */ + status = "disabled"; + }; +#endif + + hdmi@7e902000 { /* hdmi */ + status = "disabled"; + }; + + usb@7e980000 { /* usb */ + compatible = "brcm,bcm2708-usb"; + reg = <0x7e980000 0x10000>, + <0x7e006000 0x1000>; + interrupt-names = "usb", + "soft"; + interrupts = <1 9>, + <2 0>; + }; + +#ifndef BCM2711 + v3d@7ec00000 { /* vd3 */ + compatible = "brcm,vc4-v3d"; + power-domains = <&power RPI_POWER_DOMAIN_V3D>; + status = "disabled"; + }; +#endif + + axiperf: axiperf { + compatible = "brcm,bcm2835-axiperf"; + reg = <0x7e009800 0x100>, + <0x7ee08000 0x100>; + firmware = <&firmware>; + status = "disabled"; + }; + }; + + __overrides__ { + cam0-pwdn-ctrl; + cam0-pwdn; + cam0-led-ctrl; + cam0-led; + }; +}; + +&gpio { + interrupts = <2 17>, <2 18>; + + dpi_18bit_cpadhi_gpio0: dpi_18bit_cpadhi_gpio0 { + brcm,pins = <0 1 2 3 4 5 6 7 8 9 + 12 13 14 15 16 17 + 20 21 22 23 24 25>; + brcm,function = ; + brcm,pull = <0>; /* no pull */ + }; + dpi_18bit_cpadhi_gpio2: dpi_18bit_cpadhi_gpio2 { + brcm,pins = <2 3 4 5 6 7 8 9 + 12 13 14 15 16 17 + 20 21 22 23 24 25>; + brcm,function = ; + }; + dpi_18bit_gpio0: dpi_18bit_gpio0 { + brcm,pins = <0 1 2 3 4 5 6 7 8 9 10 11 + 12 13 14 15 16 17 18 19 + 20 21>; + brcm,function = ; + }; + dpi_18bit_gpio2: dpi_18bit_gpio2 { + brcm,pins = <2 3 4 5 6 7 8 9 10 11 + 12 13 14 15 16 17 18 19 + 20 21>; + brcm,function = ; + }; +}; + +&uart0 { + /* Enable CTS bug workaround */ + cts-event-workaround; +}; + +&i2s { + #sound-dai-cells = <0>; + dmas = <&dma 2>, <&dma 3>; + dma-names = "tx", "rx"; +}; + +&sdhost { + dmas = <&dma (13|(1<<29))>; + dma-names = "rx-tx"; + bus-width = <4>; + brcm,overclock-50 = <0>; + brcm,pio-limit = <1>; + firmware = <&firmware>; +}; + +&spi0 { + dmas = <&dma 6>, <&dma 7>; + dma-names = "tx", "rx"; +}; diff --git a/arch/arm/boot/dts/bcm2710-rpi-2-b.dts b/arch/arm/boot/dts/bcm2710-rpi-2-b.dts new file mode 100644 index 000000000000..ae9db1b1be1b --- /dev/null +++ b/arch/arm/boot/dts/bcm2710-rpi-2-b.dts @@ -0,0 +1,129 @@ +/dts-v1/; + +#include "bcm2710.dtsi" +#include "bcm2709-rpi.dtsi" +#include "bcm283x-rpi-smsc9514.dtsi" +#include "bcm283x-rpi-csi1-2lane.dtsi" +#include "bcm283x-rpi-i2c0mux_0_28.dtsi" +#include "bcm283x-rpi-cam1-regulator.dtsi" + +/ { + compatible = "raspberrypi,2-model-b-rev2", "brcm,bcm2837"; + model = "Raspberry Pi 2 Model B rev 1.2"; +}; + +&gpio { + spi0_pins: spi0_pins { + brcm,pins = <9 10 11>; + brcm,function = <4>; /* alt0 */ + }; + + spi0_cs_pins: spi0_cs_pins { + brcm,pins = <8 7>; + brcm,function = <1>; /* output */ + }; + + i2c0_pins: i2c0 { + brcm,pins = <0 1>; + brcm,function = <4>; + }; + + i2c1_pins: i2c1 { + brcm,pins = <2 3>; + brcm,function = <4>; + }; + + i2s_pins: i2s { + brcm,pins = <18 19 20 21>; + brcm,function = <4>; /* alt0 */ + }; + + audio_pins: audio_pins { + brcm,pins = <40 45>; + brcm,function = <4>; + }; +}; + +&uart0 { + status = "okay"; +}; + +&spi0 { + pinctrl-names = "default"; + pinctrl-0 = <&spi0_pins &spi0_cs_pins>; + cs-gpios = <&gpio 8 1>, <&gpio 7 1>; + + spidev0: spidev@0{ + compatible = "spidev"; + reg = <0>; /* CE0 */ + #address-cells = <1>; + #size-cells = <0>; + spi-max-frequency = <125000000>; + }; + + spidev1: spidev@1{ + compatible = "spidev"; + reg = <1>; /* CE1 */ + #address-cells = <1>; + #size-cells = <0>; + spi-max-frequency = <125000000>; + }; +}; + +&i2c0if { + clock-frequency = <100000>; +}; + +&i2c1 { + pinctrl-names = "default"; + pinctrl-0 = <&i2c1_pins>; + clock-frequency = <100000>; +}; + +&i2c2 { + clock-frequency = <100000>; +}; + +&i2s { + pinctrl-names = "default"; + pinctrl-0 = <&i2s_pins>; +}; + +&leds { + act_led: led-act { + label = "led0"; + linux,default-trigger = "mmc0"; + gpios = <&gpio 47 0>; + }; + + pwr_led: led-pwr { + label = "led1"; + linux,default-trigger = "input"; + gpios = <&gpio 35 0>; + }; +}; + +&hdmi { + hpd-gpios = <&gpio 46 GPIO_ACTIVE_LOW>; +}; + +&audio { + pinctrl-names = "default"; + pinctrl-0 = <&audio_pins>; +}; + +&cam1_reg { + gpio = <&gpio 41 GPIO_ACTIVE_HIGH>; +}; + +/ { + __overrides__ { + act_led_gpio = <&act_led>,"gpios:4"; + act_led_activelow = <&act_led>,"gpios:8"; + act_led_trigger = <&act_led>,"linux,default-trigger"; + + pwr_led_gpio = <&pwr_led>,"gpios:4"; + pwr_led_activelow = <&pwr_led>,"gpios:8"; + pwr_led_trigger = <&pwr_led>,"linux,default-trigger"; + }; +}; diff --git a/arch/arm/boot/dts/bcm2710-rpi-3-b-plus.dts b/arch/arm/boot/dts/bcm2710-rpi-3-b-plus.dts new file mode 100644 index 000000000000..7e12c05cc28b --- /dev/null +++ b/arch/arm/boot/dts/bcm2710-rpi-3-b-plus.dts @@ -0,0 +1,201 @@ +/dts-v1/; + +#include "bcm2710.dtsi" +#include "bcm2709-rpi.dtsi" +#include "bcm283x-rpi-lan7515.dtsi" +#include "bcm283x-rpi-csi1-2lane.dtsi" +#include "bcm283x-rpi-i2c0mux_0_44.dtsi" +#include "bcm271x-rpi-bt.dtsi" +#include "bcm283x-rpi-cam1-regulator.dtsi" + +/ { + compatible = "raspberrypi,3-model-b-plus", "brcm,bcm2837"; + model = "Raspberry Pi 3 Model B+"; + + chosen { + bootargs = "coherent_pool=1M 8250.nr_uarts=1 snd_bcm2835.enable_compat_alsa=0 snd_bcm2835.enable_hdmi=1"; + }; + + aliases { + serial0 = &uart1; + serial1 = &uart0; + mmc1 = &mmcnr; + }; +}; + +&gpio { + spi0_pins: spi0_pins { + brcm,pins = <9 10 11>; + brcm,function = <4>; /* alt0 */ + }; + + spi0_cs_pins: spi0_cs_pins { + brcm,pins = <8 7>; + brcm,function = <1>; /* output */ + }; + + i2c0_pins: i2c0 { + brcm,pins = <0 1>; + brcm,function = <4>; + }; + + i2c1_pins: i2c1 { + brcm,pins = <2 3>; + brcm,function = <4>; + }; + + i2s_pins: i2s { + brcm,pins = <18 19 20 21>; + brcm,function = <4>; /* alt0 */ + }; + + sdio_pins: sdio_pins { + brcm,pins = <34 35 36 37 38 39>; + brcm,function = <7>; // alt3 = SD1 + brcm,pull = <0 2 2 2 2 2>; + }; + + bt_pins: bt_pins { + brcm,pins = <43>; + brcm,function = <4>; /* alt0:GPCLK2 */ + brcm,pull = <0>; + }; + + uart0_pins: uart0_pins { + brcm,pins = <32 33>; + brcm,function = <7>; /* alt3=UART0 */ + brcm,pull = <0 2>; + }; + + uart1_pins: uart1_pins { + brcm,pins; + brcm,function; + brcm,pull; + }; + + audio_pins: audio_pins { + brcm,pins = <40 41>; + brcm,function = <4>; + }; +}; + +&mmcnr { + pinctrl-names = "default"; + pinctrl-0 = <&sdio_pins>; + bus-width = <4>; + status = "okay"; +}; + +&firmware { + expgpio: expgpio { + compatible = "raspberrypi,firmware-gpio"; + gpio-controller; + #gpio-cells = <2>; + status = "okay"; + }; +}; + +&uart0 { + pinctrl-names = "default"; + pinctrl-0 = <&uart0_pins &bt_pins>; + status = "okay"; +}; + +&uart1 { + pinctrl-names = "default"; + pinctrl-0 = <&uart1_pins>; + status = "okay"; +}; + +&spi0 { + pinctrl-names = "default"; + pinctrl-0 = <&spi0_pins &spi0_cs_pins>; + cs-gpios = <&gpio 8 1>, <&gpio 7 1>; + + spidev0: spidev@0{ + compatible = "spidev"; + reg = <0>; /* CE0 */ + #address-cells = <1>; + #size-cells = <0>; + spi-max-frequency = <125000000>; + }; + + spidev1: spidev@1{ + compatible = "spidev"; + reg = <1>; /* CE1 */ + #address-cells = <1>; + #size-cells = <0>; + spi-max-frequency = <125000000>; + }; +}; + +&i2c0if { + clock-frequency = <100000>; +}; + +&i2c1 { + pinctrl-names = "default"; + pinctrl-0 = <&i2c1_pins>; + clock-frequency = <100000>; +}; + +&i2c2 { + clock-frequency = <100000>; +}; + +&i2s { + pinctrl-names = "default"; + pinctrl-0 = <&i2s_pins>; +}; + +&leds { + act_led: led-act { + label = "led0"; + linux,default-trigger = "mmc0"; + gpios = <&gpio 29 0>; + }; + + pwr_led: led-pwr { + label = "led1"; + linux,default-trigger = "default-on"; + gpios = <&expgpio 2 GPIO_ACTIVE_LOW>; + }; +}; + +&hdmi { + hpd-gpios = <&gpio 28 GPIO_ACTIVE_LOW>; +}; + +&audio { + pinctrl-names = "default"; + pinctrl-0 = <&audio_pins>; +}; + +ð_phy { + microchip,eee-enabled; + microchip,tx-lpi-timer = <600>; /* non-aggressive*/ + microchip,downshift-after = <2>; +}; + +&cam1_reg { + gpio = <&expgpio 5 GPIO_ACTIVE_HIGH>; +}; + +/ { + __overrides__ { + act_led_gpio = <&act_led>,"gpios:4"; + act_led_activelow = <&act_led>,"gpios:8"; + act_led_trigger = <&act_led>,"linux,default-trigger"; + + pwr_led_gpio = <&pwr_led>,"gpios:4"; + pwr_led_activelow = <&pwr_led>,"gpios:8"; + pwr_led_trigger = <&pwr_led>,"linux,default-trigger"; + + eee = <ð_phy>,"microchip,eee-enabled?"; + tx_lpi_timer = <ð_phy>,"microchip,tx-lpi-timer:0"; + eth_led0 = <ð_phy>,"microchip,led-modes:0"; + eth_led1 = <ð_phy>,"microchip,led-modes:4"; + eth_downshift_after = <ð_phy>,"microchip,downshift-after:0"; + eth_max_speed = <ð_phy>,"max-speed:0"; + }; +}; diff --git a/arch/arm/boot/dts/bcm2710-rpi-3-b.dts b/arch/arm/boot/dts/bcm2710-rpi-3-b.dts new file mode 100644 index 000000000000..d40722ddc286 --- /dev/null +++ b/arch/arm/boot/dts/bcm2710-rpi-3-b.dts @@ -0,0 +1,203 @@ +/dts-v1/; + +#include "bcm2710.dtsi" +#include "bcm2709-rpi.dtsi" +#include "bcm283x-rpi-smsc9514.dtsi" +#include "bcm283x-rpi-csi1-2lane.dtsi" +#include "bcm283x-rpi-i2c0mux_0_44.dtsi" +#include "bcm271x-rpi-bt.dtsi" +#include "bcm283x-rpi-cam1-regulator.dtsi" + +/ { + compatible = "raspberrypi,3-model-b", "brcm,bcm2837"; + model = "Raspberry Pi 3 Model B"; + + chosen { + bootargs = "coherent_pool=1M 8250.nr_uarts=1 snd_bcm2835.enable_compat_alsa=0 snd_bcm2835.enable_hdmi=1"; + }; + + aliases { + serial0 = &uart1; + serial1 = &uart0; + mmc1 = &mmcnr; + }; +}; + +&gpio { + spi0_pins: spi0_pins { + brcm,pins = <9 10 11>; + brcm,function = <4>; /* alt0 */ + }; + + spi0_cs_pins: spi0_cs_pins { + brcm,pins = <8 7>; + brcm,function = <1>; /* output */ + }; + + i2c0_pins: i2c0 { + brcm,pins = <0 1>; + brcm,function = <4>; + }; + + i2c1_pins: i2c1 { + brcm,pins = <2 3>; + brcm,function = <4>; + }; + + i2s_pins: i2s { + brcm,pins = <18 19 20 21>; + brcm,function = <4>; /* alt0 */ + }; + + sdio_pins: sdio_pins { + brcm,pins = <34 35 36 37 38 39>; + brcm,function = <7>; // alt3 = SD1 + brcm,pull = <0 2 2 2 2 2>; + }; + + bt_pins: bt_pins { + brcm,pins = <43>; + brcm,function = <4>; /* alt0:GPCLK2 */ + brcm,pull = <0>; + }; + + uart0_pins: uart0_pins { + brcm,pins = <32 33>; + brcm,function = <7>; /* alt3=UART0 */ + brcm,pull = <0 2>; + }; + + uart1_pins: uart1_pins { + brcm,pins; + brcm,function; + brcm,pull; + }; + + audio_pins: audio_pins { + brcm,pins = <40 41>; + brcm,function = <4>; + }; +}; + +&mmcnr { + pinctrl-names = "default"; + pinctrl-0 = <&sdio_pins>; + bus-width = <4>; + status = "okay"; +}; + +&soc { + virtgpio: virtgpio { + compatible = "brcm,bcm2835-virtgpio"; + gpio-controller; + #gpio-cells = <2>; + firmware = <&firmware>; + status = "okay"; + }; + +}; + +&firmware { + expgpio: expgpio { + compatible = "raspberrypi,firmware-gpio"; + gpio-controller; + #gpio-cells = <2>; + status = "okay"; + }; +}; + +&uart0 { + pinctrl-names = "default"; + pinctrl-0 = <&uart0_pins &bt_pins>; + status = "okay"; +}; + +&uart1 { + pinctrl-names = "default"; + pinctrl-0 = <&uart1_pins>; + status = "okay"; +}; + +&bt { + max-speed = <921600>; +}; + +&spi0 { + pinctrl-names = "default"; + pinctrl-0 = <&spi0_pins &spi0_cs_pins>; + cs-gpios = <&gpio 8 1>, <&gpio 7 1>; + + spidev0: spidev@0{ + compatible = "spidev"; + reg = <0>; /* CE0 */ + #address-cells = <1>; + #size-cells = <0>; + spi-max-frequency = <125000000>; + }; + + spidev1: spidev@1{ + compatible = "spidev"; + reg = <1>; /* CE1 */ + #address-cells = <1>; + #size-cells = <0>; + spi-max-frequency = <125000000>; + }; +}; + +&i2c0if { + clock-frequency = <100000>; +}; + +&i2c1 { + pinctrl-names = "default"; + pinctrl-0 = <&i2c1_pins>; + clock-frequency = <100000>; +}; + +&i2c2 { + clock-frequency = <100000>; +}; + +&i2s { + pinctrl-names = "default"; + pinctrl-0 = <&i2s_pins>; +}; + +&leds { + act_led: led-act { + label = "led0"; + linux,default-trigger = "mmc0"; + gpios = <&virtgpio 0 0>; + }; + + pwr_led: led-pwr { + label = "led1"; + linux,default-trigger = "input"; + gpios = <&expgpio 7 0>; + }; +}; + +&hdmi { + hpd-gpios = <&expgpio 4 GPIO_ACTIVE_LOW>; +}; + +&audio { + pinctrl-names = "default"; + pinctrl-0 = <&audio_pins>; +}; + +&cam1_reg { + gpio = <&expgpio 5 GPIO_ACTIVE_HIGH>; +}; + +/ { + __overrides__ { + act_led_gpio = <&act_led>,"gpios:4"; + act_led_activelow = <&act_led>,"gpios:8"; + act_led_trigger = <&act_led>,"linux,default-trigger"; + + pwr_led_gpio = <&pwr_led>,"gpios:4"; + pwr_led_activelow = <&pwr_led>,"gpios:8"; + pwr_led_trigger = <&pwr_led>,"linux,default-trigger"; + }; +}; diff --git a/arch/arm/boot/dts/bcm2710-rpi-cm3.dts b/arch/arm/boot/dts/bcm2710-rpi-cm3.dts new file mode 100644 index 000000000000..c386a855cdc3 --- /dev/null +++ b/arch/arm/boot/dts/bcm2710-rpi-cm3.dts @@ -0,0 +1,148 @@ +/dts-v1/; + +#include "bcm2710.dtsi" +#include "bcm2709-rpi.dtsi" +#include "bcm283x-rpi-csi0-2lane.dtsi" +#include "bcm283x-rpi-csi1-4lane.dtsi" +#include "bcm283x-rpi-i2c0mux_0_28.dtsi" +/ { + compatible = "raspberrypi,3-compute-module", "brcm,bcm2837"; + model = "Raspberry Pi Compute Module 3"; + + cam1_reg: cam1_reg { + compatible = "regulator-fixed"; + regulator-name = "cam1-regulator"; + gpio = <&gpio 2 GPIO_ACTIVE_HIGH>; + enable-active-high; + status = "disabled"; + }; + cam0_reg: cam0_reg { + compatible = "regulator-fixed"; + regulator-name = "cam0-regulator"; + gpio = <&gpio 30 GPIO_ACTIVE_HIGH>; + enable-active-high; + status = "disabled"; + }; +}; + +&uart0 { + status = "okay"; +}; + +&gpio { + spi0_pins: spi0_pins { + brcm,pins = <9 10 11>; + brcm,function = <4>; /* alt0 */ + }; + + spi0_cs_pins: spi0_cs_pins { + brcm,pins = <8 7>; + brcm,function = <1>; /* output */ + }; + + i2c0_pins: i2c0 { + brcm,pins = <0 1>; + brcm,function = <4>; + }; + + i2c1_pins: i2c1 { + brcm,pins = <2 3>; + brcm,function = <4>; + }; + + i2s_pins: i2s { + brcm,pins = <18 19 20 21>; + brcm,function = <4>; /* alt0 */ + }; + + audio_pins: audio_pins { + brcm,pins; + brcm,function; + }; +}; + +&soc { + virtgpio: virtgpio { + compatible = "brcm,bcm2835-virtgpio"; + gpio-controller; + #gpio-cells = <2>; + firmware = <&firmware>; + status = "okay"; + }; + +}; + +&firmware { + expgpio: expgpio { + compatible = "raspberrypi,firmware-gpio"; + gpio-controller; + #gpio-cells = <2>; + status = "okay"; + }; +}; + +&spi0 { + pinctrl-names = "default"; + pinctrl-0 = <&spi0_pins &spi0_cs_pins>; + cs-gpios = <&gpio 8 1>, <&gpio 7 1>; + + spidev0: spidev@0{ + compatible = "spidev"; + reg = <0>; /* CE0 */ + #address-cells = <1>; + #size-cells = <0>; + spi-max-frequency = <125000000>; + }; + + spidev1: spidev@1{ + compatible = "spidev"; + reg = <1>; /* CE1 */ + #address-cells = <1>; + #size-cells = <0>; + spi-max-frequency = <125000000>; + }; +}; + +&i2c0if { + clock-frequency = <100000>; +}; + +&i2c1 { + pinctrl-names = "default"; + pinctrl-0 = <&i2c1_pins>; + clock-frequency = <100000>; +}; + +&i2c2 { + clock-frequency = <100000>; +}; + +&i2s { + pinctrl-names = "default"; + pinctrl-0 = <&i2s_pins>; +}; + +&leds { + act_led: led-act { + label = "led0"; + linux,default-trigger = "mmc0"; + gpios = <&virtgpio 0 0>; + }; +}; + +&hdmi { + hpd-gpios = <&expgpio 0 GPIO_ACTIVE_LOW>; +}; + +&audio { + pinctrl-names = "default"; + pinctrl-0 = <&audio_pins>; +}; + +/ { + __overrides__ { + act_led_gpio = <&act_led>,"gpios:4"; + act_led_activelow = <&act_led>,"gpios:8"; + act_led_trigger = <&act_led>,"linux,default-trigger"; + }; +}; diff --git a/arch/arm/boot/dts/bcm2710.dtsi b/arch/arm/boot/dts/bcm2710.dtsi new file mode 100644 index 000000000000..e7e5c913f1d1 --- /dev/null +++ b/arch/arm/boot/dts/bcm2710.dtsi @@ -0,0 +1,25 @@ +#include "bcm2837.dtsi" +#include "bcm270x.dtsi" + +/ { + compatible = "brcm,bcm2837", "brcm,bcm2836"; + + arm-pmu { + compatible = "arm,cortex-a53-pmu", "arm,cortex-a7-pmu"; + }; + + soc { + /delete-node/ timer@7e003000; + }; + + __overrides__ { + arm_freq = <&cpu0>, "clock-frequency:0", + <&cpu1>, "clock-frequency:0", + <&cpu2>, "clock-frequency:0", + <&cpu3>, "clock-frequency:0"; + }; +}; + +&vc4 { + status = "disabled"; +}; diff --git a/arch/arm/boot/dts/bcm2711-rpi-4-b.dts b/arch/arm/boot/dts/bcm2711-rpi-4-b.dts index 72ce80fbf266..f6e0247f7d1b 100644 --- a/arch/arm/boot/dts/bcm2711-rpi-4-b.dts +++ b/arch/arm/boot/dts/bcm2711-rpi-4-b.dts @@ -2,7 +2,7 @@ /dts-v1/; #include "bcm2711.dtsi" #include "bcm2711-rpi.dtsi" -#include "bcm283x-rpi-usb-peripheral.dtsi" +//#include "bcm283x-rpi-usb-peripheral.dtsi" / { compatible = "raspberrypi,4-model-b", "brcm,bcm2711"; @@ -72,7 +72,7 @@ "VDD_SD_IO_SEL", "CAM_GPIO", "SD_PWR_ON", - ""; + "SD_OC_N"; }; &gpio { @@ -260,3 +260,309 @@ &vec { status = "disabled"; }; + +// ============================================= +// Downstream rpi- changes + +#define BCM2711 + +#include "bcm270x.dtsi" +#include "bcm271x-rpi-bt.dtsi" + +/ { + soc { + /delete-node/ pixelvalve@7e807000; + /delete-node/ hdmi@7e902000; + }; +}; + +#include "bcm2711-rpi-ds.dtsi" +#include "bcm283x-rpi-csi1-2lane.dtsi" +#include "bcm283x-rpi-i2c0mux_0_44.dtsi" +#include "bcm283x-rpi-cam1-regulator.dtsi" + +/ { + chosen { + bootargs = "coherent_pool=1M 8250.nr_uarts=1 snd_bcm2835.enable_compat_alsa=0 snd_bcm2835.enable_hdmi=1"; + }; + + aliases { + serial0 = &uart1; + serial1 = &uart0; + mmc0 = &emmc2; + mmc1 = &mmcnr; + mmc2 = &sdhost; + i2c3 = &i2c3; + i2c4 = &i2c4; + i2c5 = &i2c5; + i2c6 = &i2c6; + i2c20 = &ddc0; + i2c21 = &ddc1; + spi3 = &spi3; + spi4 = &spi4; + spi5 = &spi5; + spi6 = &spi6; + /delete-property/ intc; + }; + + /delete-node/ wifi-pwrseq; +}; + +&mmcnr { + pinctrl-names = "default"; + pinctrl-0 = <&sdio_pins>; + bus-width = <4>; + status = "okay"; +}; + +&uart0 { + pinctrl-0 = <&uart0_pins &bt_pins>; + status = "okay"; +}; + +&uart1 { + pinctrl-0 = <&uart1_pins>; +}; + +&spi0 { + pinctrl-names = "default"; + pinctrl-0 = <&spi0_pins &spi0_cs_pins>; + cs-gpios = <&gpio 8 1>, <&gpio 7 1>; + + spidev0: spidev@0{ + compatible = "spidev"; + reg = <0>; /* CE0 */ + #address-cells = <1>; + #size-cells = <0>; + spi-max-frequency = <125000000>; + }; + + spidev1: spidev@1{ + compatible = "spidev"; + reg = <1>; /* CE1 */ + #address-cells = <1>; + #size-cells = <0>; + spi-max-frequency = <125000000>; + }; +}; + +&gpio { + spi0_pins: spi0_pins { + brcm,pins = <9 10 11>; + brcm,function = ; + }; + + spi0_cs_pins: spi0_cs_pins { + brcm,pins = <8 7>; + brcm,function = ; + }; + + spi3_pins: spi3_pins { + brcm,pins = <1 2 3>; + brcm,function = ; + }; + + spi3_cs_pins: spi3_cs_pins { + brcm,pins = <0 24>; + brcm,function = ; + }; + + spi4_pins: spi4_pins { + brcm,pins = <5 6 7>; + brcm,function = ; + }; + + spi4_cs_pins: spi4_cs_pins { + brcm,pins = <4 25>; + brcm,function = ; + }; + + spi5_pins: spi5_pins { + brcm,pins = <13 14 15>; + brcm,function = ; + }; + + spi5_cs_pins: spi5_cs_pins { + brcm,pins = <12 26>; + brcm,function = ; + }; + + spi6_pins: spi6_pins { + brcm,pins = <19 20 21>; + brcm,function = ; + }; + + spi6_cs_pins: spi6_cs_pins { + brcm,pins = <18 27>; + brcm,function = ; + }; + + i2c0_pins: i2c0 { + brcm,pins = <0 1>; + brcm,function = ; + brcm,pull = ; + }; + + i2c1_pins: i2c1 { + brcm,pins = <2 3>; + brcm,function = ; + brcm,pull = ; + }; + + i2c3_pins: i2c3 { + brcm,pins = <4 5>; + brcm,function = ; + brcm,pull = ; + }; + + i2c4_pins: i2c4 { + brcm,pins = <8 9>; + brcm,function = ; + brcm,pull = ; + }; + + i2c5_pins: i2c5 { + brcm,pins = <12 13>; + brcm,function = ; + brcm,pull = ; + }; + + i2c6_pins: i2c6 { + brcm,pins = <22 23>; + brcm,function = ; + brcm,pull = ; + }; + + i2s_pins: i2s { + brcm,pins = <18 19 20 21>; + brcm,function = ; + }; + + sdio_pins: sdio_pins { + brcm,pins = <34 35 36 37 38 39>; + brcm,function = ; // alt3 = SD1 + brcm,pull = <0 2 2 2 2 2>; + }; + + bt_pins: bt_pins { + brcm,pins = "-"; // non-empty to keep btuart happy, //4 = 0 + // to fool pinctrl + brcm,function = <0>; + brcm,pull = <2>; + }; + + uart0_pins: uart0_pins { + brcm,pins = <32 33>; + brcm,function = ; + brcm,pull = <0 2>; + }; + + uart1_pins: uart1_pins { + brcm,pins; + brcm,function; + brcm,pull; + }; + + uart2_pins: uart2_pins { + brcm,pins = <0 1>; + brcm,function = ; + brcm,pull = <0 2>; + }; + + uart3_pins: uart3_pins { + brcm,pins = <4 5>; + brcm,function = ; + brcm,pull = <0 2>; + }; + + uart4_pins: uart4_pins { + brcm,pins = <8 9>; + brcm,function = ; + brcm,pull = <0 2>; + }; + + uart5_pins: uart5_pins { + brcm,pins = <12 13>; + brcm,function = ; + brcm,pull = <0 2>; + }; +}; + +&i2c0if { + clock-frequency = <100000>; +}; + +&i2c1 { + pinctrl-names = "default"; + pinctrl-0 = <&i2c1_pins>; + clock-frequency = <100000>; +}; + +&i2s { + pinctrl-names = "default"; + pinctrl-0 = <&i2s_pins>; +}; + +// ============================================= +// Board specific stuff here + +&sdhost { + status = "disabled"; +}; + +&phy1 { + led-modes = <0x00 0x08>; /* link/activity link */ +}; + +&gpio { + audio_pins: audio_pins { + brcm,pins = <40 41>; + brcm,function = <4>; + }; +}; + +&leds { + act_led: led-act { + label = "led0"; + linux,default-trigger = "mmc0"; + gpios = <&gpio 42 GPIO_ACTIVE_HIGH>; + }; + + pwr_led: led-pwr { + label = "led1"; + linux,default-trigger = "default-on"; + gpios = <&expgpio 2 GPIO_ACTIVE_LOW>; + }; +}; + +&pwm1 { + status = "disabled"; +}; + +&audio { + pinctrl-names = "default"; + pinctrl-0 = <&audio_pins>; +}; + +&cam1_reg { + gpio = <&expgpio 5 GPIO_ACTIVE_HIGH>; +}; + +/ { + __overrides__ { + act_led_gpio = <&act_led>,"gpios:4"; + act_led_activelow = <&act_led>,"gpios:8"; + act_led_trigger = <&act_led>,"linux,default-trigger"; + + pwr_led_gpio = <&pwr_led>,"gpios:4"; + pwr_led_activelow = <&pwr_led>,"gpios:8"; + pwr_led_trigger = <&pwr_led>,"linux,default-trigger"; + + eth_led0 = <&phy1>,"led-modes:0"; + eth_led1 = <&phy1>,"led-modes:4"; + + sd_poll_once = <&emmc2>, "non-removable?"; + spi_dma4 = <&spi0>, "dmas:0=", <&dma40>, + <&spi0>, "dmas:8=", <&dma40>; + }; +}; diff --git a/arch/arm/boot/dts/bcm2711-rpi-400.dts b/arch/arm/boot/dts/bcm2711-rpi-400.dts index f4d2fc20397c..bed192b085df 100644 --- a/arch/arm/boot/dts/bcm2711-rpi-400.dts +++ b/arch/arm/boot/dts/bcm2711-rpi-400.dts @@ -1,6 +1,9 @@ // SPDX-License-Identifier: GPL-2.0 /dts-v1/; -#include "bcm2711-rpi-4-b.dts" +#include "bcm2711.dtsi" +#include "bcm2835-rpi.dtsi" + +#include / { compatible = "raspberrypi,400", "brcm,bcm2711"; @@ -11,35 +14,624 @@ stdout-path = "serial1:115200n8"; }; + /* Will be filled by the bootloader */ + memory@0 { + device_type = "memory"; + reg = <0 0 0>; + }; + + aliases { + emmc2bus = &emmc2bus; + ethernet0 = &genet; + pcie0 = &pcie0; + blconfig = &blconfig; + }; + leds { - /delete-node/ led-act; + led-act { + gpios = <&gpio 42 GPIO_ACTIVE_HIGH>; + }; led-pwr { - gpios = <&gpio 42 GPIO_ACTIVE_HIGH>; + label = "PWR"; + gpios = <&expgpio 2 GPIO_ACTIVE_LOW>; + default-state = "keep"; + linux,default-trigger = "default-on"; }; }; - gpio-poweroff { - compatible = "gpio-poweroff"; - gpios = <&expgpio 5 GPIO_ACTIVE_HIGH>; + wifi_pwrseq: wifi-pwrseq { + compatible = "mmc-pwrseq-simple"; + reset-gpios = <&expgpio 1 GPIO_ACTIVE_LOW>; + }; + + sd_io_1v8_reg: sd_io_1v8_reg { + compatible = "regulator-gpio"; + regulator-name = "vdd-sd-io"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <3300000>; + regulator-boot-on; + regulator-always-on; + regulator-settling-time-us = <5000>; + gpios = <&expgpio 4 GPIO_ACTIVE_HIGH>; + states = <1800000 0x1 + 3300000 0x0>; + status = "okay"; + }; + + sd_vcc_reg: sd_vcc_reg { + compatible = "regulator-fixed"; + regulator-name = "vcc-sd"; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + regulator-boot-on; + enable-active-high; + gpio = <&expgpio 6 GPIO_ACTIVE_HIGH>; }; }; -&expgpio { - gpio-line-names = "BT_ON", - "WL_ON", - "", - "GLOBAL_RESET", - "VDD_SD_IO_SEL", - "CAM_GPIO", - "SD_PWR_ON", - "SD_OC_N"; +&ddc0 { + status = "okay"; +}; + +&ddc1 { + status = "okay"; +}; + +&firmware { + firmware_clocks: clocks { + compatible = "raspberrypi,firmware-clocks"; + #clock-cells = <1>; + }; + + expgpio: gpio { + compatible = "raspberrypi,firmware-gpio"; + gpio-controller; + #gpio-cells = <2>; + gpio-line-names = "BT_ON", + "WL_ON", + "PWR_LED_OFF", + "GLOBAL_RESET", + "VDD_SD_IO_SEL", + "CAM_GPIO", + "SD_PWR_ON", + "SD_OC_N"; + status = "okay"; + }; + + reset: reset { + compatible = "raspberrypi,firmware-reset"; + #reset-cells = <1>; + }; +}; + +&gpio { + /* + * Parts taken from rpi_SCH_4b_4p0_reduced.pdf and + * the official GPU firmware DT blob. + * + * Legend: + * "FOO" = GPIO line named "FOO" on the schematic + * "FOO_N" = GPIO line named "FOO" on schematic, active low + */ + gpio-line-names = "ID_SDA", + "ID_SCL", + "SDA1", + "SCL1", + "GPIO_GCLK", + "GPIO5", + "GPIO6", + "SPI_CE1_N", + "SPI_CE0_N", + "SPI_MISO", + "SPI_MOSI", + "SPI_SCLK", + "GPIO12", + "GPIO13", + /* Serial port */ + "TXD1", + "RXD1", + "GPIO16", + "GPIO17", + "GPIO18", + "GPIO19", + "GPIO20", + "GPIO21", + "GPIO22", + "GPIO23", + "GPIO24", + "GPIO25", + "GPIO26", + "GPIO27", + "RGMII_MDIO", + "RGMIO_MDC", + /* Used by BT module */ + "CTS0", + "RTS0", + "TXD0", + "RXD0", + /* Used by Wifi */ + "SD1_CLK", + "SD1_CMD", + "SD1_DATA0", + "SD1_DATA1", + "SD1_DATA2", + "SD1_DATA3", + /* Shared with SPI flash */ + "PWM0_MISO", + "PWM1_MOSI", + "STATUS_LED_G_CLK", + "SPIFLASH_CE_N", + "SDA0", + "SCL0", + "RGMII_RXCLK", + "RGMII_RXCTL", + "RGMII_RXD0", + "RGMII_RXD1", + "RGMII_RXD2", + "RGMII_RXD3", + "RGMII_TXCLK", + "RGMII_TXCTL", + "RGMII_TXD0", + "RGMII_TXD1", + "RGMII_TXD2", + "RGMII_TXD3"; +}; + +&hdmi0 { + clocks = <&firmware_clocks 13>, <&firmware_clocks 14>, <&dvp 0>, <&clk_27MHz>; + clock-names = "hdmi", "bvb", "audio", "cec"; + wifi-2.4ghz-coexistence; + status = "okay"; +}; + +&hdmi1 { + clocks = <&firmware_clocks 13>, <&firmware_clocks 14>, <&dvp 1>, <&clk_27MHz>; + clock-names = "hdmi", "bvb", "audio", "cec"; + wifi-2.4ghz-coexistence; + status = "okay"; +}; + +&hvs { + clocks = <&firmware_clocks 4>; +}; + +&pixelvalve0 { + status = "okay"; +}; + +&pixelvalve1 { + status = "okay"; +}; + +&pixelvalve2 { + status = "okay"; +}; + +&pixelvalve4 { + status = "okay"; +}; + +&pwm1 { + pinctrl-names = "default"; + pinctrl-0 = <&pwm1_0_gpio40 &pwm1_1_gpio41>; + status = "okay"; +}; + +&rmem { + /* + * RPi4's co-processor will copy the board's bootloader configuration + * into memory for the OS to consume. It'll also update this node with + * its placement information. + */ + blconfig: nvram@0 { + compatible = "raspberrypi,bootloader-config", "nvmem-rmem"; + #address-cells = <1>; + #size-cells = <1>; + reg = <0x0 0x0 0x0>; + no-map; + status = "disabled"; + }; +}; + +/* SDHCI is used to control the SDIO for wireless */ +&sdhci { + #address-cells = <1>; + #size-cells = <0>; + pinctrl-names = "default"; + pinctrl-0 = <&emmc_gpio34>; + bus-width = <4>; + non-removable; + mmc-pwrseq = <&wifi_pwrseq>; + status = "okay"; + + brcmf: wifi@1 { + reg = <1>; + compatible = "brcm,bcm4329-fmac"; + }; +}; + +/* EMMC2 is used to drive the SD card */ +&emmc2 { + vqmmc-supply = <&sd_io_1v8_reg>; + vmmc-supply = <&sd_vcc_reg>; + broken-cd; + status = "okay"; +}; + +&genet { + phy-handle = <&phy1>; + phy-mode = "rgmii-rxid"; + status = "okay"; +}; + +&genet_mdio { + phy1: ethernet-phy@1 { + /* No PHY interrupt */ + reg = <0x1>; + }; +}; + +&pcie0 { + pci@0,0 { + device-type = "pci"; + #address-cells = <3>; + #size-cells = <2>; + ranges; + + reg = <0 0 0 0 0>; + + usb@0,0 { + reg = <0x0 0 0 0 0>; + resets = <&reset RASPBERRYPI_FIRMWARE_RESET_ID_USB>; + }; + }; +}; + +/* uart0 communicates with the BT module */ +&uart0 { + pinctrl-names = "default"; + pinctrl-0 = <&uart0_ctsrts_gpio30 &uart0_gpio32>; + uart-has-rtscts; + status = "okay"; + + bluetooth { + compatible = "brcm,bcm43438-bt"; + max-speed = <2000000>; + shutdown-gpios = <&expgpio 0 GPIO_ACTIVE_HIGH>; + }; +}; + +/* uart1 is mapped to the pin header */ +&uart1 { + pinctrl-names = "default"; + pinctrl-0 = <&uart1_gpio14>; + status = "okay"; +}; + +&vchiq { + interrupts = ; +}; + +&vc4 { + status = "okay"; +}; + +&vec { + status = "disabled"; +}; + +// ============================================= +// Downstream rpi- changes + +#define BCM2711 + +#include "bcm270x.dtsi" +#include "bcm271x-rpi-bt.dtsi" + +/ { + soc { + /delete-node/ pixelvalve@7e807000; + /delete-node/ hdmi@7e902000; + }; +}; + +#include "bcm2711-rpi-ds.dtsi" +#include "bcm283x-rpi-csi1-2lane.dtsi" +#include "bcm283x-rpi-i2c0mux_0_44.dtsi" + +/ { + chosen { + bootargs = "coherent_pool=1M 8250.nr_uarts=1 snd_bcm2835.enable_compat_alsa=0 snd_bcm2835.enable_hdmi=1"; + }; + + aliases { + serial0 = &uart1; + serial1 = &uart0; + mmc0 = &emmc2; + mmc1 = &mmcnr; + mmc2 = &sdhost; + i2c3 = &i2c3; + i2c4 = &i2c4; + i2c5 = &i2c5; + i2c6 = &i2c6; + i2c20 = &ddc0; + i2c21 = &ddc1; + spi3 = &spi3; + spi4 = &spi4; + spi5 = &spi5; + spi6 = &spi6; + /delete-property/ intc; + }; + + /delete-node/ wifi-pwrseq; +}; + +&mmcnr { + pinctrl-names = "default"; + pinctrl-0 = <&sdio_pins>; + bus-width = <4>; + status = "okay"; +}; + +&uart0 { + pinctrl-0 = <&uart0_pins &bt_pins>; + status = "okay"; +}; + +&uart1 { + pinctrl-0 = <&uart1_pins>; +}; + +&spi0 { + pinctrl-names = "default"; + pinctrl-0 = <&spi0_pins &spi0_cs_pins>; + cs-gpios = <&gpio 8 1>, <&gpio 7 1>; + + spidev0: spidev@0{ + compatible = "spidev"; + reg = <0>; /* CE0 */ + #address-cells = <1>; + #size-cells = <0>; + spi-max-frequency = <125000000>; + }; + + spidev1: spidev@1{ + compatible = "spidev"; + reg = <1>; /* CE1 */ + #address-cells = <1>; + #size-cells = <0>; + spi-max-frequency = <125000000>; + }; +}; + +&gpio { + spi0_pins: spi0_pins { + brcm,pins = <9 10 11>; + brcm,function = ; + }; + + spi0_cs_pins: spi0_cs_pins { + brcm,pins = <8 7>; + brcm,function = ; + }; + + spi3_pins: spi3_pins { + brcm,pins = <1 2 3>; + brcm,function = ; + }; + + spi3_cs_pins: spi3_cs_pins { + brcm,pins = <0 24>; + brcm,function = ; + }; + + spi4_pins: spi4_pins { + brcm,pins = <5 6 7>; + brcm,function = ; + }; + + spi4_cs_pins: spi4_cs_pins { + brcm,pins = <4 25>; + brcm,function = ; + }; + + spi5_pins: spi5_pins { + brcm,pins = <13 14 15>; + brcm,function = ; + }; + + spi5_cs_pins: spi5_cs_pins { + brcm,pins = <12 26>; + brcm,function = ; + }; + + spi6_pins: spi6_pins { + brcm,pins = <19 20 21>; + brcm,function = ; + }; + + spi6_cs_pins: spi6_cs_pins { + brcm,pins = <18 27>; + brcm,function = ; + }; + + i2c0_pins: i2c0 { + brcm,pins = <0 1>; + brcm,function = ; + brcm,pull = ; + }; + + i2c1_pins: i2c1 { + brcm,pins = <2 3>; + brcm,function = ; + brcm,pull = ; + }; + + i2c3_pins: i2c3 { + brcm,pins = <4 5>; + brcm,function = ; + brcm,pull = ; + }; + + i2c4_pins: i2c4 { + brcm,pins = <8 9>; + brcm,function = ; + brcm,pull = ; + }; + + i2c5_pins: i2c5 { + brcm,pins = <12 13>; + brcm,function = ; + brcm,pull = ; + }; + + i2c6_pins: i2c6 { + brcm,pins = <22 23>; + brcm,function = ; + brcm,pull = ; + }; + + i2s_pins: i2s { + brcm,pins = <18 19 20 21>; + brcm,function = ; + }; + + sdio_pins: sdio_pins { + brcm,pins = <34 35 36 37 38 39>; + brcm,function = ; // alt3 = SD1 + brcm,pull = <0 2 2 2 2 2>; + }; + + bt_pins: bt_pins { + brcm,pins = "-"; // non-empty to keep btuart happy, //4 = 0 + // to fool pinctrl + brcm,function = <0>; + brcm,pull = <2>; + }; + + uart0_pins: uart0_pins { + brcm,pins = <32 33>; + brcm,function = ; + brcm,pull = <0 2>; + }; + + uart1_pins: uart1_pins { + brcm,pins; + brcm,function; + brcm,pull; + }; + + uart2_pins: uart2_pins { + brcm,pins = <0 1>; + brcm,function = ; + brcm,pull = <0 2>; + }; + + uart3_pins: uart3_pins { + brcm,pins = <4 5>; + brcm,function = ; + brcm,pull = <0 2>; + }; + + uart4_pins: uart4_pins { + brcm,pins = <8 9>; + brcm,function = ; + brcm,pull = <0 2>; + }; + + uart5_pins: uart5_pins { + brcm,pins = <12 13>; + brcm,function = ; + brcm,pull = <0 2>; + }; +}; + +&i2c0if { + clock-frequency = <100000>; +}; + +&i2c1 { + pinctrl-names = "default"; + pinctrl-0 = <&i2c1_pins>; + clock-frequency = <100000>; +}; + +&i2s { + pinctrl-names = "default"; + pinctrl-0 = <&i2s_pins>; +}; + +// ============================================= +// Board specific stuff here + +/ { + power_ctrl: power_ctrl { + compatible = "gpio-poweroff"; + gpios = <&expgpio 5 0>; + force; + }; +}; + +&sdhost { + status = "disabled"; +}; + +&phy1 { + led-modes = <0x00 0x08>; /* link/activity link */ +}; + +&gpio { + audio_pins: audio_pins { + brcm,pins = <>; + brcm,function = <>; + }; +}; + +&leds { + act_led: led-act { + label = "led0"; + linux,default-trigger = "default-on"; + default-state = "on"; + gpios = <&gpio 42 GPIO_ACTIVE_HIGH>; + }; + + pwr_led: led-pwr { + label = "led1"; + linux,default-trigger = "default-on"; + gpios = <&expgpio 2 GPIO_ACTIVE_LOW>; + }; +}; + +&pwm1 { + status = "disabled"; +}; + +&audio { + pinctrl-names = "default"; + pinctrl-0 = <&audio_pins>; + brcm,disable-headphones = <1>; }; &genet_mdio { clock-frequency = <1950000>; }; -&pm { - /delete-property/ system-power-controller; +/ { + __overrides__ { + act_led_gpio = <&act_led>,"gpios:4"; + act_led_activelow = <&act_led>,"gpios:8"; + act_led_trigger = <&act_led>,"linux,default-trigger"; + + pwr_led_gpio = <&pwr_led>,"gpios:4"; + pwr_led_activelow = <&pwr_led>,"gpios:8"; + pwr_led_trigger = <&pwr_led>,"linux,default-trigger"; + + eth_led0 = <&phy1>,"led-modes:0"; + eth_led1 = <&phy1>,"led-modes:4"; + + sd_poll_once = <&emmc2>, "non-removable?"; + spi_dma4 = <&spi0>, "dmas:0=", <&dma40>, + <&spi0>, "dmas:8=", <&dma40>; + }; }; diff --git a/arch/arm/boot/dts/bcm2711-rpi-cm4.dts b/arch/arm/boot/dts/bcm2711-rpi-cm4.dts new file mode 100644 index 000000000000..76dd97513a20 --- /dev/null +++ b/arch/arm/boot/dts/bcm2711-rpi-cm4.dts @@ -0,0 +1,660 @@ +// SPDX-License-Identifier: GPL-2.0 +/dts-v1/; +#include "bcm2711.dtsi" +#include "bcm2835-rpi.dtsi" + +#include + +/ { + compatible = "raspberrypi,4-compute-module", "brcm,bcm2711"; + model = "Raspberry Pi Compute Module 4"; + + chosen { + /* 8250 auxiliary UART instead of pl011 */ + stdout-path = "serial1:115200n8"; + }; + + /* Will be filled by the bootloader */ + memory@0 { + device_type = "memory"; + reg = <0 0 0>; + }; + + aliases { + emmc2bus = &emmc2bus; + ethernet0 = &genet; + pcie0 = &pcie0; + blconfig = &blconfig; + }; + + leds { + led-act { + gpios = <&gpio 42 GPIO_ACTIVE_HIGH>; + }; + + led-pwr { + label = "PWR"; + gpios = <&expgpio 2 GPIO_ACTIVE_LOW>; + default-state = "keep"; + linux,default-trigger = "default-on"; + }; + }; + + wifi_pwrseq: wifi-pwrseq { + compatible = "mmc-pwrseq-simple"; + reset-gpios = <&expgpio 1 GPIO_ACTIVE_LOW>; + }; + + sd_io_1v8_reg: sd_io_1v8_reg { + compatible = "regulator-gpio"; + regulator-name = "vdd-sd-io"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <3300000>; + regulator-boot-on; + regulator-always-on; + regulator-settling-time-us = <5000>; + gpios = <&expgpio 4 GPIO_ACTIVE_HIGH>; + states = <1800000 0x1 + 3300000 0x0>; + status = "okay"; + }; + + sd_vcc_reg: sd_vcc_reg { + compatible = "regulator-fixed"; + regulator-name = "vcc-sd"; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + regulator-boot-on; + enable-active-high; + gpio = <&expgpio 6 GPIO_ACTIVE_HIGH>; + }; +}; + +&ddc0 { + status = "okay"; +}; + +&ddc1 { + status = "okay"; +}; + +&firmware { + firmware_clocks: clocks { + compatible = "raspberrypi,firmware-clocks"; + #clock-cells = <1>; + }; + + expgpio: gpio { + compatible = "raspberrypi,firmware-gpio"; + gpio-controller; + #gpio-cells = <2>; + gpio-line-names = "BT_ON", + "WL_ON", + "PWR_LED_OFF", + "ANT1", + "VDD_SD_IO_SEL", + "CAM_GPIO", + "SD_PWR_ON", + "ANT2"; + status = "okay"; + + ant1: ant1 { + gpio-hog; + gpios = <3 GPIO_ACTIVE_HIGH>; + output-high; + }; + + ant2: ant2 { + gpio-hog; + gpios = <7 GPIO_ACTIVE_HIGH>; + output-low; + }; + }; + + reset: reset { + compatible = "raspberrypi,firmware-reset"; + #reset-cells = <1>; + }; +}; + +&gpio { + /* + * Parts taken from rpi_SCH_4b_4p0_reduced.pdf and + * the official GPU firmware DT blob. + * + * Legend: + * "FOO" = GPIO line named "FOO" on the schematic + * "FOO_N" = GPIO line named "FOO" on schematic, active low + */ + gpio-line-names = "ID_SDA", + "ID_SCL", + "SDA1", + "SCL1", + "GPIO_GCLK", + "GPIO5", + "GPIO6", + "SPI_CE1_N", + "SPI_CE0_N", + "SPI_MISO", + "SPI_MOSI", + "SPI_SCLK", + "GPIO12", + "GPIO13", + /* Serial port */ + "TXD1", + "RXD1", + "GPIO16", + "GPIO17", + "GPIO18", + "GPIO19", + "GPIO20", + "GPIO21", + "GPIO22", + "GPIO23", + "GPIO24", + "GPIO25", + "GPIO26", + "GPIO27", + "RGMII_MDIO", + "RGMIO_MDC", + /* Used by BT module */ + "CTS0", + "RTS0", + "TXD0", + "RXD0", + /* Used by Wifi */ + "SD1_CLK", + "SD1_CMD", + "SD1_DATA0", + "SD1_DATA1", + "SD1_DATA2", + "SD1_DATA3", + /* Shared with SPI flash */ + "PWM0_MISO", + "PWM1_MOSI", + "STATUS_LED_G_CLK", + "SPIFLASH_CE_N", + "SDA0", + "SCL0", + "RGMII_RXCLK", + "RGMII_RXCTL", + "RGMII_RXD0", + "RGMII_RXD1", + "RGMII_RXD2", + "RGMII_RXD3", + "RGMII_TXCLK", + "RGMII_TXCTL", + "RGMII_TXD0", + "RGMII_TXD1", + "RGMII_TXD2", + "RGMII_TXD3"; +}; + +&hdmi0 { + clocks = <&firmware_clocks 13>, <&firmware_clocks 14>, <&dvp 0>, <&clk_27MHz>; + clock-names = "hdmi", "bvb", "audio", "cec"; + wifi-2.4ghz-coexistence; + status = "okay"; +}; + +&hdmi1 { + clocks = <&firmware_clocks 13>, <&firmware_clocks 14>, <&dvp 1>, <&clk_27MHz>; + clock-names = "hdmi", "bvb", "audio", "cec"; + wifi-2.4ghz-coexistence; + status = "okay"; +}; + +&hvs { + clocks = <&firmware_clocks 4>; +}; + +&pixelvalve0 { + status = "okay"; +}; + +&pixelvalve1 { + status = "okay"; +}; + +&pixelvalve2 { + status = "okay"; +}; + +&pixelvalve4 { + status = "okay"; +}; + +&pwm1 { + pinctrl-names = "default"; + pinctrl-0 = <&pwm1_0_gpio40 &pwm1_1_gpio41>; + status = "okay"; +}; + +&rmem { + /* + * RPi4's co-processor will copy the board's bootloader configuration + * into memory for the OS to consume. It'll also update this node with + * its placement information. + */ + blconfig: nvram@0 { + compatible = "raspberrypi,bootloader-config", "nvmem-rmem"; + #address-cells = <1>; + #size-cells = <1>; + reg = <0x0 0x0 0x0>; + no-map; + status = "disabled"; + }; +}; + +/* SDHCI is used to control the SDIO for wireless */ +&sdhci { + #address-cells = <1>; + #size-cells = <0>; + pinctrl-names = "default"; + pinctrl-0 = <&emmc_gpio34>; + bus-width = <4>; + non-removable; + mmc-pwrseq = <&wifi_pwrseq>; + status = "okay"; + + brcmf: wifi@1 { + reg = <1>; + compatible = "brcm,bcm4329-fmac"; + }; +}; + +/* EMMC2 is used to drive the EMMC card */ +&emmc2 { + bus-width = <8>; + vqmmc-supply = <&sd_io_1v8_reg>; + vmmc-supply = <&sd_vcc_reg>; + broken-cd; + status = "okay"; +}; + +&genet { + phy-handle = <&phy1>; + phy-mode = "rgmii-rxid"; + status = "okay"; +}; + +&genet_mdio { + phy1: ethernet-phy@0 { + /* No PHY interrupt */ + reg = <0x0>; + }; +}; + +&pcie0 { + pci@0,0 { + device-type = "pci"; + #address-cells = <3>; + #size-cells = <2>; + ranges; + + reg = <0 0 0 0 0>; + + usb@0,0 { + reg = <0 0 0 0 0>; + resets = <&reset RASPBERRYPI_FIRMWARE_RESET_ID_USB>; + }; + }; +}; + +/* uart0 communicates with the BT module */ +&uart0 { + pinctrl-names = "default"; + pinctrl-0 = <&uart0_ctsrts_gpio30 &uart0_gpio32>; + uart-has-rtscts; + status = "okay"; + + bluetooth { + compatible = "brcm,bcm43438-bt"; + max-speed = <2000000>; + shutdown-gpios = <&expgpio 0 GPIO_ACTIVE_HIGH>; + }; +}; + +/* uart1 is mapped to the pin header */ +&uart1 { + pinctrl-names = "default"; + pinctrl-0 = <&uart1_gpio14>; + status = "okay"; +}; + +&vchiq { + interrupts = ; +}; + +&vc4 { + status = "okay"; +}; + +&vec { + status = "disabled"; +}; + +// ============================================= +// Downstream rpi- changes + +#define BCM2711 + +#include "bcm270x.dtsi" +#include "bcm271x-rpi-bt.dtsi" + +/ { + soc { + /delete-node/ pixelvalve@7e807000; + /delete-node/ hdmi@7e902000; + }; +}; + +#include "bcm2711-rpi-ds.dtsi" +#include "bcm283x-rpi-csi0-2lane.dtsi" +#include "bcm283x-rpi-csi1-4lane.dtsi" +#include "bcm283x-rpi-i2c0mux_0_44.dtsi" +#include "bcm283x-rpi-cam1-regulator.dtsi" + +/ { + chosen { + bootargs = "coherent_pool=1M 8250.nr_uarts=1 snd_bcm2835.enable_compat_alsa=0 snd_bcm2835.enable_hdmi=1"; + }; + + aliases { + serial0 = &uart1; + serial1 = &uart0; + mmc0 = &emmc2; + mmc1 = &mmcnr; + mmc2 = &sdhost; + i2c3 = &i2c3; + i2c4 = &i2c4; + i2c5 = &i2c5; + i2c6 = &i2c6; + i2c20 = &ddc0; + i2c21 = &ddc1; + spi3 = &spi3; + spi4 = &spi4; + spi5 = &spi5; + spi6 = &spi6; + /delete-property/ intc; + }; + + /delete-node/ wifi-pwrseq; +}; + +&mmcnr { + pinctrl-names = "default"; + pinctrl-0 = <&sdio_pins>; + bus-width = <4>; + status = "okay"; +}; + +&uart0 { + pinctrl-0 = <&uart0_pins &bt_pins>; + status = "okay"; +}; + +&uart1 { + pinctrl-0 = <&uart1_pins>; +}; + +&spi0 { + pinctrl-names = "default"; + pinctrl-0 = <&spi0_pins &spi0_cs_pins>; + cs-gpios = <&gpio 8 1>, <&gpio 7 1>; + + spidev0: spidev@0{ + compatible = "spidev"; + reg = <0>; /* CE0 */ + #address-cells = <1>; + #size-cells = <0>; + spi-max-frequency = <125000000>; + }; + + spidev1: spidev@1{ + compatible = "spidev"; + reg = <1>; /* CE1 */ + #address-cells = <1>; + #size-cells = <0>; + spi-max-frequency = <125000000>; + }; +}; + +&gpio { + spi0_pins: spi0_pins { + brcm,pins = <9 10 11>; + brcm,function = ; + }; + + spi0_cs_pins: spi0_cs_pins { + brcm,pins = <8 7>; + brcm,function = ; + }; + + spi3_pins: spi3_pins { + brcm,pins = <1 2 3>; + brcm,function = ; + }; + + spi3_cs_pins: spi3_cs_pins { + brcm,pins = <0 24>; + brcm,function = ; + }; + + spi4_pins: spi4_pins { + brcm,pins = <5 6 7>; + brcm,function = ; + }; + + spi4_cs_pins: spi4_cs_pins { + brcm,pins = <4 25>; + brcm,function = ; + }; + + spi5_pins: spi5_pins { + brcm,pins = <13 14 15>; + brcm,function = ; + }; + + spi5_cs_pins: spi5_cs_pins { + brcm,pins = <12 26>; + brcm,function = ; + }; + + spi6_pins: spi6_pins { + brcm,pins = <19 20 21>; + brcm,function = ; + }; + + spi6_cs_pins: spi6_cs_pins { + brcm,pins = <18 27>; + brcm,function = ; + }; + + i2c0_pins: i2c0 { + brcm,pins = <0 1>; + brcm,function = ; + brcm,pull = ; + }; + + i2c1_pins: i2c1 { + brcm,pins = <2 3>; + brcm,function = ; + brcm,pull = ; + }; + + i2c3_pins: i2c3 { + brcm,pins = <4 5>; + brcm,function = ; + brcm,pull = ; + }; + + i2c4_pins: i2c4 { + brcm,pins = <8 9>; + brcm,function = ; + brcm,pull = ; + }; + + i2c5_pins: i2c5 { + brcm,pins = <12 13>; + brcm,function = ; + brcm,pull = ; + }; + + i2c6_pins: i2c6 { + brcm,pins = <22 23>; + brcm,function = ; + brcm,pull = ; + }; + + i2s_pins: i2s { + brcm,pins = <18 19 20 21>; + brcm,function = ; + }; + + sdio_pins: sdio_pins { + brcm,pins = <34 35 36 37 38 39>; + brcm,function = ; // alt3 = SD1 + brcm,pull = <0 2 2 2 2 2>; + }; + + bt_pins: bt_pins { + brcm,pins = "-"; // non-empty to keep btuart happy, //4 = 0 + // to fool pinctrl + brcm,function = <0>; + brcm,pull = <2>; + }; + + uart0_pins: uart0_pins { + brcm,pins = <32 33>; + brcm,function = ; + brcm,pull = <0 2>; + }; + + uart1_pins: uart1_pins { + brcm,pins; + brcm,function; + brcm,pull; + }; + + uart2_pins: uart2_pins { + brcm,pins = <0 1>; + brcm,function = ; + brcm,pull = <0 2>; + }; + + uart3_pins: uart3_pins { + brcm,pins = <4 5>; + brcm,function = ; + brcm,pull = <0 2>; + }; + + uart4_pins: uart4_pins { + brcm,pins = <8 9>; + brcm,function = ; + brcm,pull = <0 2>; + }; + + uart5_pins: uart5_pins { + brcm,pins = <12 13>; + brcm,function = ; + brcm,pull = <0 2>; + }; +}; + +&i2c0if { + clock-frequency = <100000>; +}; + +&i2c1 { + pinctrl-names = "default"; + pinctrl-0 = <&i2c1_pins>; + clock-frequency = <100000>; +}; + +&i2s { + pinctrl-names = "default"; + pinctrl-0 = <&i2s_pins>; +}; + +// ============================================= +// Board specific stuff here + +&pcie0 { + brcm,enable-l1ss; +}; + +&sdhost { + status = "disabled"; +}; + +&phy1 { + led-modes = <0x00 0x08>; /* link/activity link */ +}; + +&gpio { + audio_pins: audio_pins { + brcm,pins = <>; + brcm,function = <>; + }; +}; + +&leds { + act_led: led-act { + label = "led0"; + linux,default-trigger = "mmc0"; + gpios = <&gpio 42 GPIO_ACTIVE_HIGH>; + }; + + pwr_led: led-pwr { + label = "led1"; + linux,default-trigger = "default-on"; + gpios = <&expgpio 2 GPIO_ACTIVE_LOW>; + }; +}; + +&pwm1 { + status = "disabled"; +}; + +&audio { + pinctrl-names = "default"; + pinctrl-0 = <&audio_pins>; + brcm,disable-headphones = <1>; +}; + +cam0_reg: &cam1_reg { + gpio = <&expgpio 5 GPIO_ACTIVE_HIGH>; +}; + +/ { + __overrides__ { + act_led_gpio = <&act_led>,"gpios:4"; + act_led_activelow = <&act_led>,"gpios:8"; + act_led_trigger = <&act_led>,"linux,default-trigger"; + + pwr_led_gpio = <&pwr_led>,"gpios:4"; + pwr_led_activelow = <&pwr_led>,"gpios:8"; + pwr_led_trigger = <&pwr_led>,"linux,default-trigger"; + + eth_led0 = <&phy1>,"led-modes:0"; + eth_led1 = <&phy1>,"led-modes:4"; + + ant1 = <&ant1>,"output-high?=on", + <&ant1>, "output-low?=off", + <&ant2>, "output-high?=off", + <&ant2>, "output-low?=on"; + ant2 = <&ant1>,"output-high?=off", + <&ant1>, "output-low?=on", + <&ant2>, "output-high?=on", + <&ant2>, "output-low?=off"; + noant = <&ant1>,"output-high?=off", + <&ant1>, "output-low?=on", + <&ant2>, "output-high?=off", + <&ant2>, "output-low?=on"; + + sd_poll_once = <&emmc2>, "non-removable?"; + spi_dma4 = <&spi0>, "dmas:0=", <&dma40>, + <&spi0>, "dmas:8=", <&dma40>; + }; +}; diff --git a/arch/arm/boot/dts/bcm2711-rpi-ds.dtsi b/arch/arm/boot/dts/bcm2711-rpi-ds.dtsi new file mode 100644 index 000000000000..ebf73b789b4a --- /dev/null +++ b/arch/arm/boot/dts/bcm2711-rpi-ds.dtsi @@ -0,0 +1,205 @@ +// SPDX-License-Identifier: GPL-2.0 +#include "bcm270x-rpi.dtsi" + +/ { + __overrides__ { + arm_freq; + }; + + v3dbus: v3dbus { + compatible = "simple-bus"; + #address-cells = <1>; + #size-cells = <2>; + ranges = <0x7c500000 0x0 0xfc500000 0x0 0x03300000>, + <0x40000000 0x0 0xff800000 0x0 0x00800000>; + dma-ranges = <0x00000000 0x0 0x00000000 0x4 0x00000000>; + + v3d: v3d@7ec04000 { + compatible = "brcm,2711-v3d"; + reg = + <0x7ec00000 0x0 0x4000>, + <0x7ec04000 0x0 0x4000>; + reg-names = "hub", "core0"; + + power-domains = <&pm BCM2835_POWER_DOMAIN_GRAFX_V3D>; + resets = <&pm BCM2835_RESET_V3D>; + clocks = <&firmware_clocks 5>; + clocks-names = "v3d"; + interrupts = ; + status = "disabled"; + }; + }; + + scb: scb { + /* Add a label */ + }; +}; + +&vc4 { + raspberrypi,firmware = <&firmware>; +}; + +&cma { + /* Limit cma to the lower 768MB to allow room for HIGHMEM on 32-bit */ + alloc-ranges = <0x0 0x00000000 0x30000000>; +}; + +&scb { + ranges = <0x0 0x7c000000 0x0 0xfc000000 0x0 0x03800000>, + <0x0 0x40000000 0x0 0xff800000 0x0 0x00800000>, + <0x6 0x00000000 0x6 0x00000000 0x0 0x40000000>, + <0x0 0x00000000 0x0 0x00000000 0x0 0xfc000000>; + dma-ranges = <0x0 0x00000000 0x0 0x00000000 0x4 0x00000000>; + + dma40: dma@7e007b00 { + compatible = "brcm,bcm2711-dma"; + reg = <0x0 0x7e007b00 0x0 0x400>; + interrupts = + , /* dma4 11 */ + , /* dma4 12 */ + , /* dma4 13 */ + ; /* dma4 14 */ + interrupt-names = "dma11", + "dma12", + "dma13", + "dma14"; + #dma-cells = <1>; + brcm,dma-channel-mask = <0x7800>; + }; + + xhci: xhci@7e9c0000 { + compatible = "generic-xhci"; + status = "disabled"; + reg = <0x0 0x7e9c0000 0x0 0x100000>; + interrupts = ; + power-domains = <&power RPI_POWER_DOMAIN_USB>; + }; + + hevc-decoder@7eb00000 { + compatible = "raspberrypi,rpivid-hevc-decoder"; + reg = <0x0 0x7eb00000 0x0 0x10000>; + status = "okay"; + }; + + rpivid-local-intc@7eb10000 { + compatible = "raspberrypi,rpivid-local-intc"; + reg = <0x0 0x7eb10000 0x0 0x1000>; + status = "okay"; + interrupts = ; + }; + + h264-decoder@7eb20000 { + compatible = "raspberrypi,rpivid-h264-decoder"; + reg = <0x0 0x7eb20000 0x0 0x10000>; + status = "okay"; + }; + + vp9-decoder@7eb30000 { + compatible = "raspberrypi,rpivid-vp9-decoder"; + reg = <0x0 0x7eb30000 0x0 0x10000>; + status = "okay"; + }; +}; + +&dma40 { + /* The VPU firmware uses DMA channel 11 for VCHIQ */ + brcm,dma-channel-mask = <0x7000>; +}; + +&vchiq { + compatible = "brcm,bcm2711-vchiq"; +}; + +&firmwarekms { + compatible = "raspberrypi,rpi-firmware-kms-2711"; + interrupts = ; +}; + +&smi { + interrupts = ; +}; + +&mmc { + interrupts = ; +}; + +&mmcnr { + interrupts = ; +}; + +&csi0 { + interrupts = ; +}; + +&csi1 { + interrupts = ; +}; + +&random { + compatible = "brcm,bcm2711-rng200"; + status = "okay"; +}; + +&usb { + /* Enable the FIQ support */ + reg = <0x7e980000 0x10000>, + <0x7e00b200 0x200>; + interrupts = , + ; + status = "disabled"; +}; + +&gpio { + interrupts = , + ; +}; + +&emmc2 { + mmc-ddr-3_3v; +}; + +&vc4 { + status = "disabled"; +}; + +&pixelvalve0 { + status = "disabled"; +}; + +&pixelvalve1 { + status = "disabled"; +}; + +&pixelvalve2 { + status = "disabled"; +}; + +&pixelvalve3 { + status = "disabled"; +}; + +&pixelvalve4 { + status = "disabled"; +}; + +&hdmi0 { + dmas = <&dma (10|(1<<27)|(1<<24)|(10<<16)|(15<<20))>; + status = "disabled"; +}; + +&ddc0 { + status = "disabled"; +}; + +&hdmi1 { + dmas = <&dma (17|(1<<27)|(1<<24)|(10<<16)|(15<<20))>; + status = "disabled"; +}; + +&ddc1 { + status = "disabled"; +}; + +&dvp { + status = "disabled"; +}; diff --git a/arch/arm/boot/dts/bcm2711.dtsi b/arch/arm/boot/dts/bcm2711.dtsi index 21294f775a20..9ef2696b71e9 100644 --- a/arch/arm/boot/dts/bcm2711.dtsi +++ b/arch/arm/boot/dts/bcm2711.dtsi @@ -323,6 +323,7 @@ interrupts = ; interrupt-controller; #interrupt-cells = <1>; + status = "disabled"; }; hdmi0: hdmi@7ef00700 { @@ -335,7 +336,8 @@ <0x7ef01f00 0x400>, <0x7ef00200 0x80>, <0x7ef04300 0x100>, - <0x7ef20000 0x100>; + <0x7ef20000 0x100>, + <0x7ef00100 0x30>; reg-names = "hdmi", "dvp", "phy", @@ -344,7 +346,12 @@ "metadata", "csc", "cec", - "hd"; + "hd", + "intr2"; + clocks = <&firmware_clocks 13>, + <&firmware_clocks 14>, + <&dvp 0>, + <&clk_27MHz>; clock-names = "hdmi", "bvb", "audio", "cec"; resets = <&dvp 0>; interrupt-parent = <&aon_intr>; @@ -353,7 +360,7 @@ interrupt-names = "cec-tx", "cec-rx", "cec-low", "wakeup", "hpd-connected", "hpd-removed"; ddc = <&ddc0>; - dmas = <&dma 10>; + dmas = <&dma (10 | (1 << 27) | (1 << 24)| (15 << 20) | (10 << 16))>; dma-names = "audio-rx"; status = "disabled"; }; @@ -376,7 +383,8 @@ <0x7ef06f00 0x400>, <0x7ef00280 0x80>, <0x7ef09300 0x100>, - <0x7ef20000 0x100>; + <0x7ef20000 0x100>, + <0x7ef00100 0x30>; reg-names = "hdmi", "dvp", "phy", @@ -385,16 +393,21 @@ "metadata", "csc", "cec", - "hd"; + "hd", + "intr2"; ddc = <&ddc1>; clock-names = "hdmi", "bvb", "audio", "cec"; + clocks = <&firmware_clocks 13>, + <&firmware_clocks 14>, + <&dvp 0>, + <&clk_27MHz>; resets = <&dvp 1>; interrupt-parent = <&aon_intr>; interrupts = <8>, <7>, <6>, <9>, <10>, <11>; interrupt-names = "cec-tx", "cec-rx", "cec-low", "wakeup", "hpd-connected", "hpd-removed"; - dmas = <&dma 17>; + dmas = <&dma (17 | (1 << 27) | (1 << 24)| (15 << 20) | (10 << 16))>; dma-names = "audio-rx"; status = "disabled"; }; @@ -495,14 +508,14 @@ scb { compatible = "simple-bus"; #address-cells = <2>; - #size-cells = <1>; + #size-cells = <2>; - ranges = <0x0 0x7c000000 0x0 0xfc000000 0x03800000>, - <0x6 0x00000000 0x6 0x00000000 0x40000000>; + ranges = <0x0 0x7c000000 0x0 0xfc000000 0x0 0x03800000>, + <0x6 0x00000000 0x6 0x00000000 0x0 0x40000000>; pcie0: pcie@7d500000 { compatible = "brcm,bcm2711-pcie"; - reg = <0x0 0x7d500000 0x9310>; + reg = <0x0 0x7d500000 0x0 0x9310>; device_type = "pci"; #address-cells = <3>; #interrupt-cells = <1>; @@ -522,8 +535,8 @@ msi-controller; msi-parent = <&pcie0>; - ranges = <0x02000000 0x0 0xf8000000 0x6 0x00000000 - 0x0 0x04000000>; + ranges = <0x02000000 0x0 0xc0000000 0x6 0x00000000 + 0x0 0x40000000>; /* * The wrapper around the PCIe block has a bug * preventing it from accessing beyond the first 3GB of @@ -536,7 +549,7 @@ genet: ethernet@7d580000 { compatible = "brcm,bcm2711-genet-v5"; - reg = <0x0 0x7d580000 0x10000>; + reg = <0x0 0x7d580000 0x0 0x10000>; #address-cells = <0x1>; #size-cells = <0x1>; interrupts = , @@ -1046,7 +1059,7 @@ alloc-ranges = <0x0 0x00000000 0x40000000>; }; -&i2c0 { +&i2c0if { compatible = "brcm,bcm2711-i2c", "brcm,bcm2835-i2c"; interrupts = ; }; @@ -1102,8 +1115,3 @@ &usb { interrupts = ; }; - -&vec { - compatible = "brcm,bcm2711-vec"; - interrupts = ; -}; diff --git a/arch/arm/boot/dts/bcm271x-rpi-bt.dtsi b/arch/arm/boot/dts/bcm271x-rpi-bt.dtsi new file mode 100644 index 000000000000..6b9b79f74cf3 --- /dev/null +++ b/arch/arm/boot/dts/bcm271x-rpi-bt.dtsi @@ -0,0 +1,26 @@ +// SPDX-License-Identifier: GPL-2.0 + +&uart0 { + bt: bluetooth { + compatible = "brcm,bcm43438-bt"; + max-speed = <3000000>; + shutdown-gpios = <&expgpio 0 GPIO_ACTIVE_HIGH>; + status = "disabled"; + }; +}; + +&uart1 { + minibt: bluetooth { + compatible = "brcm,bcm43438-bt"; + max-speed = <460800>; + shutdown-gpios = <&expgpio 0 GPIO_ACTIVE_HIGH>; + status = "disabled"; + }; +}; + +/ { + __overrides__ { + krnbt = <&bt>,"status"; + krnbt_baudrate = <&bt>,"max-speed:0"; + }; +}; diff --git a/arch/arm/boot/dts/bcm2835-common.dtsi b/arch/arm/boot/dts/bcm2835-common.dtsi index c25e797b9060..06d8c3882cb7 100644 --- a/arch/arm/boot/dts/bcm2835-common.dtsi +++ b/arch/arm/boot/dts/bcm2835-common.dtsi @@ -124,12 +124,14 @@ compatible = "brcm,bcm2835-hdmi"; reg = <0x7e902000 0x600>, <0x7e808000 0x100>; + reg-names = "hdmi", + "hd"; interrupts = <2 8>, <2 9>; ddc = <&i2c2>; clocks = <&clocks BCM2835_PLLH_PIX>, <&clocks BCM2835_CLOCK_HSM>; clock-names = "pixel", "hdmi"; - dmas = <&dma 17>; + dmas = <&dma (17|(1<<27)|(1<<24))>; dma-names = "audio-rx"; status = "disabled"; }; diff --git a/arch/arm/boot/dts/bcm2835-rpi-a-plus.dts b/arch/arm/boot/dts/bcm2835-rpi-a-plus.dts index 40b9405f1a8e..d2384d8e8555 100644 --- a/arch/arm/boot/dts/bcm2835-rpi-a-plus.dts +++ b/arch/arm/boot/dts/bcm2835-rpi-a-plus.dts @@ -126,3 +126,8 @@ pinctrl-0 = <&uart0_gpio14>; status = "okay"; }; + +/* i2c on camera/display connector is gpio 28&29 */ +&i2c0mux { + pinctrl-1 = <&i2c0_gpio28>; +}; diff --git a/arch/arm/boot/dts/bcm2835-rpi-a.dts b/arch/arm/boot/dts/bcm2835-rpi-a.dts index 11edb581dbaf..4ceca674b752 100644 --- a/arch/arm/boot/dts/bcm2835-rpi-a.dts +++ b/arch/arm/boot/dts/bcm2835-rpi-a.dts @@ -121,3 +121,10 @@ pinctrl-0 = <&uart0_gpio14>; status = "okay"; }; + +/* i2c0 on camera/display connector is gpio 0&1. Not exposed on header. + * To avoid having to remap everything, map both ports to gpios 0&1 + */ +&i2c0mux { + pinctrl-1 = <&i2c0_gpio0>; +}; diff --git a/arch/arm/boot/dts/bcm2835-rpi-b-plus.dts b/arch/arm/boot/dts/bcm2835-rpi-b-plus.dts index 1b435c64bd9c..8f2d10d82fa1 100644 --- a/arch/arm/boot/dts/bcm2835-rpi-b-plus.dts +++ b/arch/arm/boot/dts/bcm2835-rpi-b-plus.dts @@ -128,3 +128,8 @@ pinctrl-0 = <&uart0_gpio14>; status = "okay"; }; + +/* i2c on camera/display connector is gpio 28&29 */ +&i2c0mux { + pinctrl-1 = <&i2c0_gpio28>; +}; diff --git a/arch/arm/boot/dts/bcm2835-rpi-b-rev2.dts b/arch/arm/boot/dts/bcm2835-rpi-b-rev2.dts index a23c25c00eea..547c88a3ae9f 100644 --- a/arch/arm/boot/dts/bcm2835-rpi-b-rev2.dts +++ b/arch/arm/boot/dts/bcm2835-rpi-b-rev2.dts @@ -121,3 +121,10 @@ pinctrl-0 = <&uart0_gpio14>; status = "okay"; }; + +/* i2c0 on camera/display connector is gpio 0&1. Not exposed on header. + * To avoid having to remap everything, map both ports to gpios 0&1 + */ +&i2c0mux { + pinctrl-1 = <&i2c0_gpio0>; +}; diff --git a/arch/arm/boot/dts/bcm2835-rpi-b.dts b/arch/arm/boot/dts/bcm2835-rpi-b.dts index 1b63d6b19750..073fc99ef8a2 100644 --- a/arch/arm/boot/dts/bcm2835-rpi-b.dts +++ b/arch/arm/boot/dts/bcm2835-rpi-b.dts @@ -116,3 +116,10 @@ pinctrl-0 = <&uart0_gpio14>; status = "okay"; }; + +/* camera/display connector use BSC1 on GPIOS 2&3. + * To avoid having to remap everything, map both ports to gpios 0&1 + */ +&i2c0mux { + pinctrl-1 = <&i2c0_gpio0>; +}; diff --git a/arch/arm/boot/dts/bcm2835-rpi-cm1-io1.dts b/arch/arm/boot/dts/bcm2835-rpi-cm1-io1.dts index a75c882e6575..95564c93a645 100644 --- a/arch/arm/boot/dts/bcm2835-rpi-cm1-io1.dts +++ b/arch/arm/boot/dts/bcm2835-rpi-cm1-io1.dts @@ -95,3 +95,8 @@ pinctrl-0 = <&uart0_gpio14>; status = "okay"; }; + +/* WHAT TO DO HERE? */ +&i2c0mux { + pinctrl-1 = <&i2c0_gpio28>; +}; diff --git a/arch/arm/boot/dts/bcm2835-rpi-zero-w.dts b/arch/arm/boot/dts/bcm2835-rpi-zero-w.dts index 33b2b77aa47d..3ea5c7e6be54 100644 --- a/arch/arm/boot/dts/bcm2835-rpi-zero-w.dts +++ b/arch/arm/boot/dts/bcm2835-rpi-zero-w.dts @@ -149,3 +149,8 @@ pinctrl-0 = <&uart1_gpio14>; status = "okay"; }; + +/* i2c on camera/display connector is gpio 28&29 */ +&i2c0mux { + pinctrl-1 = <&i2c0_gpio28>; +}; diff --git a/arch/arm/boot/dts/bcm2835-rpi-zero.dts b/arch/arm/boot/dts/bcm2835-rpi-zero.dts index 6f9b3a908f28..a0eabab12c99 100644 --- a/arch/arm/boot/dts/bcm2835-rpi-zero.dts +++ b/arch/arm/boot/dts/bcm2835-rpi-zero.dts @@ -117,3 +117,8 @@ pinctrl-0 = <&uart0_gpio14>; status = "okay"; }; + +/* i2c on camera/display connector is gpio 28&29 */ +&i2c0mux { + pinctrl-1 = <&i2c0_gpio28>; +}; diff --git a/arch/arm/boot/dts/bcm2835-rpi.dtsi b/arch/arm/boot/dts/bcm2835-rpi.dtsi index 87ddcad76083..edc55bba5ff4 100644 --- a/arch/arm/boot/dts/bcm2835-rpi.dtsi +++ b/arch/arm/boot/dts/bcm2835-rpi.dtsi @@ -19,6 +19,11 @@ mboxes = <&mailbox>; dma-ranges; + + firmware_clocks: clocks { + compatible = "raspberrypi,firmware-clocks"; + #clock-cells = <1>; + }; }; power: power { @@ -49,13 +54,17 @@ }; }; -&i2c0 { - pinctrl-names = "default"; - pinctrl-0 = <&i2c0_gpio0>; +&i2c0if { status = "okay"; clock-frequency = <100000>; }; +&i2c0mux { + pinctrl-0 = <&i2c0_gpio0>; + /* pinctrl-1 varies based on platform */ + status = "okay"; +}; + &i2c1 { pinctrl-names = "default"; pinctrl-0 = <&i2c1_gpio2>; @@ -67,6 +76,10 @@ power-domains = <&power RPI_POWER_DOMAIN_USB>; }; +&vc4 { + raspberrypi,firmware = <&firmware>; +}; + &vec { power-domains = <&power RPI_POWER_DOMAIN_VEC>; status = "okay"; diff --git a/arch/arm/boot/dts/bcm2835.dtsi b/arch/arm/boot/dts/bcm2835.dtsi index 0549686134ea..2ea891228ea0 100644 --- a/arch/arm/boot/dts/bcm2835.dtsi +++ b/arch/arm/boot/dts/bcm2835.dtsi @@ -19,7 +19,7 @@ soc { ranges = <0x7e000000 0x20000000 0x02000000>; - dma-ranges = <0x40000000 0x00000000 0x20000000>; + dma-ranges = <0x80000000 0x00000000 0x20000000>; }; arm-pmu { diff --git a/arch/arm/boot/dts/bcm2836-rpi-2-b.dts b/arch/arm/boot/dts/bcm2836-rpi-2-b.dts index d8af8eeac7b6..bf22b74359d8 100644 --- a/arch/arm/boot/dts/bcm2836-rpi-2-b.dts +++ b/arch/arm/boot/dts/bcm2836-rpi-2-b.dts @@ -128,3 +128,8 @@ pinctrl-0 = <&uart0_gpio14>; status = "okay"; }; + +/* i2c on camera/display connector is gpio 28&29 */ +&i2c0mux { + pinctrl-1 = <&i2c0_gpio28>; +}; diff --git a/arch/arm/boot/dts/bcm2837-rpi-3-a-plus.dts b/arch/arm/boot/dts/bcm2837-rpi-3-a-plus.dts index 77099a7871b0..9529c0475673 100644 --- a/arch/arm/boot/dts/bcm2837-rpi-3-a-plus.dts +++ b/arch/arm/boot/dts/bcm2837-rpi-3-a-plus.dts @@ -178,3 +178,8 @@ pinctrl-0 = <&uart1_gpio14>; status = "okay"; }; + +/* i2c on camera/display connector is gpio 44&45 */ +&i2c0mux { + pinctrl-1 = <&i2c0_gpio44>; +}; diff --git a/arch/arm/boot/dts/bcm2837-rpi-3-b-plus.dts b/arch/arm/boot/dts/bcm2837-rpi-3-b-plus.dts index 61010266ca9a..40cb269aed0f 100644 --- a/arch/arm/boot/dts/bcm2837-rpi-3-b-plus.dts +++ b/arch/arm/boot/dts/bcm2837-rpi-3-b-plus.dts @@ -181,3 +181,8 @@ pinctrl-0 = <&uart1_gpio14>; status = "okay"; }; + +/* i2c on camera/display connector is gpio 44&45 */ +&i2c0mux { + pinctrl-1 = <&i2c0_gpio44>; +}; diff --git a/arch/arm/boot/dts/bcm2837-rpi-3-b.dts b/arch/arm/boot/dts/bcm2837-rpi-3-b.dts index dd4a48604097..8f16b6b3fe08 100644 --- a/arch/arm/boot/dts/bcm2837-rpi-3-b.dts +++ b/arch/arm/boot/dts/bcm2837-rpi-3-b.dts @@ -174,3 +174,8 @@ status = "okay"; bus-width = <4>; }; + +/* i2c on camera/display connector is gpio 44&45 */ +&i2c0mux { + pinctrl-1 = <&i2c0_gpio44>; +}; diff --git a/arch/arm/boot/dts/bcm2837-rpi-cm3-io3.dts b/arch/arm/boot/dts/bcm2837-rpi-cm3-io3.dts index 588d9411ceb6..dde209ade51b 100644 --- a/arch/arm/boot/dts/bcm2837-rpi-cm3-io3.dts +++ b/arch/arm/boot/dts/bcm2837-rpi-cm3-io3.dts @@ -94,3 +94,8 @@ pinctrl-0 = <&uart0_gpio14>; status = "okay"; }; + +/* WHAT TO DO HERE? */ +&i2c0mux { + pinctrl-1 = <&i2c0_gpio28>; +}; diff --git a/arch/arm/boot/dts/bcm283x-rpi-cam1-regulator.dtsi b/arch/arm/boot/dts/bcm283x-rpi-cam1-regulator.dtsi new file mode 100644 index 000000000000..55237d03ed94 --- /dev/null +++ b/arch/arm/boot/dts/bcm283x-rpi-cam1-regulator.dtsi @@ -0,0 +1,10 @@ +// SPDX-License-Identifier: GPL-2.0 + +/ { + cam1_reg: cam1_reg { + compatible = "regulator-fixed"; + regulator-name = "cam1-reg"; + enable-active-high; + status = "disabled"; + }; +}; diff --git a/arch/arm/boot/dts/bcm283x-rpi-csi0-2lane.dtsi b/arch/arm/boot/dts/bcm283x-rpi-csi0-2lane.dtsi new file mode 100644 index 000000000000..6e4ce8622b47 --- /dev/null +++ b/arch/arm/boot/dts/bcm283x-rpi-csi0-2lane.dtsi @@ -0,0 +1,4 @@ +// SPDX-License-Identifier: GPL-2.0-only +&csi0 { + brcm,num-data-lanes = <2>; +}; diff --git a/arch/arm/boot/dts/bcm283x-rpi-csi1-2lane.dtsi b/arch/arm/boot/dts/bcm283x-rpi-csi1-2lane.dtsi new file mode 100644 index 000000000000..6938f4daacdc --- /dev/null +++ b/arch/arm/boot/dts/bcm283x-rpi-csi1-2lane.dtsi @@ -0,0 +1,4 @@ +// SPDX-License-Identifier: GPL-2.0-only +&csi1 { + brcm,num-data-lanes = <2>; +}; diff --git a/arch/arm/boot/dts/bcm283x-rpi-csi1-4lane.dtsi b/arch/arm/boot/dts/bcm283x-rpi-csi1-4lane.dtsi new file mode 100644 index 000000000000..b37037437bee --- /dev/null +++ b/arch/arm/boot/dts/bcm283x-rpi-csi1-4lane.dtsi @@ -0,0 +1,4 @@ +// SPDX-License-Identifier: GPL-2.0-only +&csi1 { + brcm,num-data-lanes = <4>; +}; diff --git a/arch/arm/boot/dts/bcm283x-rpi-i2c0mux_0_28.dtsi b/arch/arm/boot/dts/bcm283x-rpi-i2c0mux_0_28.dtsi new file mode 100644 index 000000000000..38f0074bce3f --- /dev/null +++ b/arch/arm/boot/dts/bcm283x-rpi-i2c0mux_0_28.dtsi @@ -0,0 +1,4 @@ +&i2c0mux { + pinctrl-0 = <&i2c0_gpio0>; + pinctrl-1 = <&i2c0_gpio28>; +}; diff --git a/arch/arm/boot/dts/bcm283x-rpi-i2c0mux_0_44.dtsi b/arch/arm/boot/dts/bcm283x-rpi-i2c0mux_0_44.dtsi new file mode 100644 index 000000000000..119946d878db --- /dev/null +++ b/arch/arm/boot/dts/bcm283x-rpi-i2c0mux_0_44.dtsi @@ -0,0 +1,4 @@ +&i2c0mux { + pinctrl-0 = <&i2c0_gpio0>; + pinctrl-1 = <&i2c0_gpio44>; +}; diff --git a/arch/arm/boot/dts/bcm283x.dtsi b/arch/arm/boot/dts/bcm283x.dtsi index c113661a6668..62d7ee513549 100644 --- a/arch/arm/boot/dts/bcm283x.dtsi +++ b/arch/arm/boot/dts/bcm283x.dtsi @@ -336,7 +336,7 @@ status = "disabled"; }; - i2c0: i2c@7e205000 { + i2c0if: i2c@7e205000 { compatible = "brcm,bcm2835-i2c"; reg = <0x7e205000 0x200>; interrupts = <2 21>; @@ -346,6 +346,30 @@ status = "disabled"; }; + i2c0mux: i2c0mux { + compatible = "i2c-mux-pinctrl"; + #address-cells = <1>; + #size-cells = <0>; + + i2c-parent = <&i2c0if>; + + pinctrl-names = "i2c0", "i2c_csi_dsi"; + + status = "disabled"; + + i2c0: i2c@0 { + reg = <0>; + #address-cells = <1>; + #size-cells = <0>; + }; + + i2c_csi_dsi: i2c@1 { + reg = <1>; + #address-cells = <1>; + #size-cells = <0>; + }; + }; + dpi: dpi@7e208000 { compatible = "brcm,bcm2835-dpi"; reg = <0x7e208000 0x8c>; diff --git a/arch/arm/boot/dts/overlays/Makefile b/arch/arm/boot/dts/overlays/Makefile new file mode 100644 index 000000000000..44aedc149ff0 --- /dev/null +++ b/arch/arm/boot/dts/overlays/Makefile @@ -0,0 +1,248 @@ +# Overlays for the Raspberry Pi platform + +dtb-$(CONFIG_ARCH_BCM2835) += overlay_map.dtb + +dtbo-$(CONFIG_ARCH_BCM2835) += \ + act-led.dtbo \ + adafruit18.dtbo \ + adau1977-adc.dtbo \ + adau7002-simple.dtbo \ + ads1015.dtbo \ + ads1115.dtbo \ + ads7846.dtbo \ + adv7282m.dtbo \ + adv728x-m.dtbo \ + akkordion-iqdacplus.dtbo \ + allo-boss-dac-pcm512x-audio.dtbo \ + allo-boss2-dac-audio.dtbo \ + allo-digione.dtbo \ + allo-katana-dac-audio.dtbo \ + allo-piano-dac-pcm512x-audio.dtbo \ + allo-piano-dac-plus-pcm512x-audio.dtbo \ + anyspi.dtbo \ + apds9960.dtbo \ + applepi-dac.dtbo \ + at86rf233.dtbo \ + audioinjector-addons.dtbo \ + audioinjector-isolated-soundcard.dtbo \ + audioinjector-ultra.dtbo \ + audioinjector-wm8731-audio.dtbo \ + audiosense-pi.dtbo \ + audremap.dtbo \ + balena-fin.dtbo \ + cap1106.dtbo \ + chipdip-dac.dtbo \ + cma.dtbo \ + dht11.dtbo \ + dionaudio-loco.dtbo \ + dionaudio-loco-v2.dtbo \ + disable-bt.dtbo \ + disable-wifi.dtbo \ + dpi18.dtbo \ + dpi18cpadhi.dtbo \ + dpi24.dtbo \ + draws.dtbo \ + dwc-otg.dtbo \ + dwc2.dtbo \ + edt-ft5406.dtbo \ + enc28j60.dtbo \ + enc28j60-spi2.dtbo \ + exc3000.dtbo \ + fe-pi-audio.dtbo \ + fsm-demo.dtbo \ + ghost-amp.dtbo \ + goodix.dtbo \ + googlevoicehat-soundcard.dtbo \ + gpio-fan.dtbo \ + gpio-ir.dtbo \ + gpio-ir-tx.dtbo \ + gpio-key.dtbo \ + gpio-led.dtbo \ + gpio-no-bank0-irq.dtbo \ + gpio-no-irq.dtbo \ + gpio-poweroff.dtbo \ + gpio-shutdown.dtbo \ + hd44780-lcd.dtbo \ + hdmi-backlight-hwhack-gpio.dtbo \ + hifiberry-amp.dtbo \ + hifiberry-amp100.dtbo \ + hifiberry-dac.dtbo \ + hifiberry-dacplus.dtbo \ + hifiberry-dacplusadc.dtbo \ + hifiberry-dacplusadcpro.dtbo \ + hifiberry-dacplusdsp.dtbo \ + hifiberry-dacplushd.dtbo \ + hifiberry-digi.dtbo \ + hifiberry-digi-pro.dtbo \ + highperi.dtbo \ + hy28a.dtbo \ + hy28b.dtbo \ + hy28b-2017.dtbo \ + i-sabre-q2m.dtbo \ + i2c-bcm2708.dtbo \ + i2c-gpio.dtbo \ + i2c-mux.dtbo \ + i2c-pwm-pca9685a.dtbo \ + i2c-rtc.dtbo \ + i2c-rtc-gpio.dtbo \ + i2c-sensor.dtbo \ + i2c0.dtbo \ + i2c1.dtbo \ + i2c3.dtbo \ + i2c4.dtbo \ + i2c5.dtbo \ + i2c6.dtbo \ + i2s-gpio28-31.dtbo \ + ilitek251x.dtbo \ + imx219.dtbo \ + imx290.dtbo \ + imx378.dtbo \ + imx477.dtbo \ + iqaudio-codec.dtbo \ + iqaudio-dac.dtbo \ + iqaudio-dacplus.dtbo \ + iqaudio-digi-wm8804-audio.dtbo \ + irs1125.dtbo \ + jedec-spi-nor.dtbo \ + justboom-both.dtbo \ + justboom-dac.dtbo \ + justboom-digi.dtbo \ + ltc294x.dtbo \ + max98357a.dtbo \ + maxtherm.dtbo \ + mbed-dac.dtbo \ + mcp23017.dtbo \ + mcp23s17.dtbo \ + mcp2515-can0.dtbo \ + mcp2515-can1.dtbo \ + mcp251xfd.dtbo \ + mcp3008.dtbo \ + mcp3202.dtbo \ + mcp342x.dtbo \ + media-center.dtbo \ + merus-amp.dtbo \ + midi-uart0.dtbo \ + midi-uart1.dtbo \ + midi-uart2.dtbo \ + midi-uart3.dtbo \ + midi-uart4.dtbo \ + midi-uart5.dtbo \ + minipitft13.dtbo \ + miniuart-bt.dtbo \ + mmc.dtbo \ + mpu6050.dtbo \ + mz61581.dtbo \ + ov5647.dtbo \ + ov7251.dtbo \ + ov9281.dtbo \ + papirus.dtbo \ + pca953x.dtbo \ + pcie-32bit-dma.dtbo \ + pibell.dtbo \ + pifacedigital.dtbo \ + pifi-40.dtbo \ + pifi-dac-hd.dtbo \ + pifi-dac-zero.dtbo \ + pifi-mini-210.dtbo \ + piglow.dtbo \ + piscreen.dtbo \ + piscreen2r.dtbo \ + pisound.dtbo \ + pitft22.dtbo \ + pitft28-capacitive.dtbo \ + pitft28-resistive.dtbo \ + pitft35-resistive.dtbo \ + pps-gpio.dtbo \ + pwm.dtbo \ + pwm-2chan.dtbo \ + pwm-ir-tx.dtbo \ + qca7000.dtbo \ + qca7000-uart0.dtbo \ + rotary-encoder.dtbo \ + rpi-backlight.dtbo \ + rpi-cirrus-wm5102.dtbo \ + rpi-dac.dtbo \ + rpi-display.dtbo \ + rpi-ft5406.dtbo \ + rpi-poe.dtbo \ + rpi-poe-plus.dtbo \ + rpi-proto.dtbo \ + rpi-sense.dtbo \ + rpi-tv.dtbo \ + rpivid-v4l2.dtbo \ + rra-digidac1-wm8741-audio.dtbo \ + sainsmart18.dtbo \ + sc16is750-i2c.dtbo \ + sc16is752-i2c.dtbo \ + sc16is752-spi0.dtbo \ + sc16is752-spi1.dtbo \ + sdhost.dtbo \ + sdio.dtbo \ + seeed-can-fd-hat-v1.dtbo \ + seeed-can-fd-hat-v2.dtbo \ + sh1106-spi.dtbo \ + si446x-spi0.dtbo \ + smi.dtbo \ + smi-dev.dtbo \ + smi-nand.dtbo \ + spi-gpio35-39.dtbo \ + spi-gpio40-45.dtbo \ + spi-rtc.dtbo \ + spi0-1cs.dtbo \ + spi0-2cs.dtbo \ + spi1-1cs.dtbo \ + spi1-2cs.dtbo \ + spi1-3cs.dtbo \ + spi2-1cs.dtbo \ + spi2-2cs.dtbo \ + spi2-3cs.dtbo \ + spi3-1cs.dtbo \ + spi3-2cs.dtbo \ + spi4-1cs.dtbo \ + spi4-2cs.dtbo \ + spi5-1cs.dtbo \ + spi5-2cs.dtbo \ + spi6-1cs.dtbo \ + spi6-2cs.dtbo \ + ssd1306.dtbo \ + ssd1306-spi.dtbo \ + ssd1331-spi.dtbo \ + ssd1351-spi.dtbo \ + superaudioboard.dtbo \ + sx150x.dtbo \ + tc358743.dtbo \ + tc358743-audio.dtbo \ + tinylcd35.dtbo \ + tpm-slb9670.dtbo \ + uart0.dtbo \ + uart1.dtbo \ + uart2.dtbo \ + uart3.dtbo \ + uart4.dtbo \ + uart5.dtbo \ + udrc.dtbo \ + ugreen-dabboard.dtbo \ + upstream.dtbo \ + upstream-pi4.dtbo \ + vc4-fkms-v3d.dtbo \ + vc4-fkms-v3d-pi4.dtbo \ + vc4-kms-dpi-at056tn53v1.dtbo \ + vc4-kms-dsi-7inch.dtbo \ + vc4-kms-dsi-lt070me05000.dtbo \ + vc4-kms-dsi-lt070me05000-v2.dtbo \ + vc4-kms-kippah-7inch.dtbo \ + vc4-kms-v3d.dtbo \ + vc4-kms-v3d-pi4.dtbo \ + vc4-kms-vga666.dtbo \ + vga666.dtbo \ + w1-gpio.dtbo \ + w1-gpio-pullup.dtbo \ + w5500.dtbo \ + wittypi.dtbo \ + wm8960-soundcard.dtbo + +targets += dtbs dtbs_install +targets += $(dtbo-y) + +always-y := $(dtbo-y) +clean-files := *.dtbo diff --git a/arch/arm/boot/dts/overlays/README b/arch/arm/boot/dts/overlays/README new file mode 100644 index 000000000000..eb2c9adfb1a8 --- /dev/null +++ b/arch/arm/boot/dts/overlays/README @@ -0,0 +1,3530 @@ +Introduction +============ + +This directory contains Device Tree overlays. Device Tree makes it possible +to support many hardware configurations with a single kernel and without the +need to explicitly load or blacklist kernel modules. Note that this isn't a +"pure" Device Tree configuration (c.f. MACH_BCM2835) - some on-board devices +are still configured by the board support code, but the intention is to +eventually reach that goal. + +On Raspberry Pi, Device Tree usage is controlled from /boot/config.txt. By +default, the Raspberry Pi kernel boots with device tree enabled. You can +completely disable DT usage (for now) by adding: + + device_tree= + +to your config.txt, which should cause your Pi to revert to the old way of +doing things after a reboot. + +In /boot you will find a .dtb for each base platform. This describes the +hardware that is part of the Raspberry Pi board. The loader (start.elf and its +siblings) selects the .dtb file appropriate for the platform by name, and reads +it into memory. At this point, all of the optional interfaces (i2c, i2s, spi) +are disabled, but they can be enabled using Device Tree parameters: + + dtparam=i2c=on,i2s=on,spi=on + +However, this shouldn't be necessary in many use cases because loading an +overlay that requires one of those interfaces will cause it to be enabled +automatically, and it is advisable to only enable interfaces if they are +needed. + +Configuring additional, optional hardware is done using Device Tree overlays +(see below). + +GPIO numbering uses the hardware pin numbering scheme (aka BCM scheme) and +not the physical pin numbers. + +raspi-config +============ + +The Advanced Options section of the raspi-config utility can enable and disable +Device Tree use, as well as toggling the I2C and SPI interfaces. Note that it +is possible to both enable an interface and blacklist the driver, if for some +reason you should want to defer the loading. + +Modules +======= + +As well as describing the hardware, Device Tree also gives enough information +to allow suitable driver modules to be located and loaded, with the corollary +that unneeded modules are not loaded. As a result it should be possible to +remove lines from /etc/modules, and /etc/modprobe.d/raspi-blacklist.conf can +have its contents deleted (or commented out). + +Using Overlays +============== + +Overlays are loaded using the "dtoverlay" config.txt setting. As an example, +consider I2C Real Time Clock drivers. In the pre-DT world these would be loaded +by writing a magic string comprising a device identifier and an I2C address to +a special file in /sys/class/i2c-adapter, having first loaded the driver for +the I2C interface and the RTC device - something like this: + + modprobe i2c-bcm2835 + modprobe rtc-ds1307 + echo ds1307 0x68 > /sys/class/i2c-adapter/i2c-1/new_device + +With DT enabled, this becomes a line in config.txt: + + dtoverlay=i2c-rtc,ds1307 + +This causes the file /boot/overlays/i2c-rtc.dtbo to be loaded and a "node" +describing the DS1307 I2C device to be added to the Device Tree for the Pi. By +default it usees address 0x68, but this can be modified with an additional DT +parameter: + + dtoverlay=i2c-rtc,ds1307,addr=0x68 + +Parameters usually have default values, although certain parameters are +mandatory. See the list of overlays below for a description of the parameters +and their defaults. + +Making new Overlays based on existing Overlays +============================================== + +Recent overlays have been designed in a more general way, so that they can be +adapted to hardware by changing their parameters. When you have additional +hardware with more than one device of a kind, you end up using the same overlay +multiple times with other parameters, e.g. + + # 2 CAN FD interfaces on spi but with different pins + dtoverlay=mcp251xfd,spi0-0,interrupt=25 + dtoverlay=mcp251xfd,spi0-1,interrupt=24 + + # a realtime clock on i2c + dtoverlay=i2c-rtc,pcf85063 + +While this approach does work, it requires knowledge about the hardware design. +It is more feasible to simplify things for the end user by providing a single +overlay as it is done the traditional way. + +A new overlay can be generated by using ovmerge utility. +https://github.com/raspberrypi/utils/blob/master/ovmerge/ovmerge + +To generate an overlay for the above configuration we pass the configuration +to ovmerge and add the -c flag. + + ovmerge -c mcp251xfd-overlay.dts,spi0-0,interrupt=25 \ + mcp251xfd-overlay.dts,spi0-1,interrupt=24 \ + i2c-rtc-overlay.dts,pcf85063 \ + >> merged-overlay.dts + +The -c option writes the command above as a comment into the overlay as +a marker that this overlay is generated and how it was generated. +After compiling the overlay it can be loaded in a single line. + + dtoverlay=merged + +It does the same as the original configuration but without parameters. + +The Overlay and Parameter Reference +=================================== + +N.B. When editing this file, please preserve the indentation levels to make it +simple to parse programmatically. NO HARD TABS. + + +Name: +Info: Configures the base Raspberry Pi hardware +Load: +Params: + ant1 Select antenna 1 (default). CM4 only. + + ant2 Select antenna 2. CM4 only. + + noant Disable both antennas. CM4 only. + + audio Set to "on" to enable the onboard ALSA audio + interface (default "off") + + axiperf Set to "on" to enable the AXI bus performance + monitors. + See /sys/kernel/debug/raspberrypi_axi_monitor + for the results. + + eee Enable Energy Efficient Ethernet support for + compatible devices (default "on"). See also + "tx_lpi_timer". Pi3B+ only. + + eth_downshift_after Set the number of auto-negotiation failures + after which the 1000Mbps modes are disabled. + Legal values are 2, 3, 4, 5 and 0, where + 0 means never downshift (default 2). Pi3B+ only. + + eth_led0 Set mode of LED0 - amber on Pi3B+ (default "1"), + green on Pi4 (default "0"). + The legal values are: + + Pi3B+ + + 0=link/activity 1=link1000/activity + 2=link100/activity 3=link10/activity + 4=link100/1000/activity 5=link10/1000/activity + 6=link10/100/activity 14=off 15=on + + Pi4 + + 0=Speed/Activity 1=Speed + 2=Flash activity 3=FDX + 4=Off 5=On + 6=Alt 7=Speed/Flash + 8=Link 9=Activity + + eth_led1 Set mode of LED1 - green on Pi3B+ (default "6"), + amber on Pi4 (default "8"). See eth_led0 for + legal values. + + eth_max_speed Set the maximum speed a link is allowed + to negotiate. Legal values are 10, 100 and + 1000 (default 1000). Pi3B+ only. + + i2c_arm Set to "on" to enable the ARM's i2c interface + (default "off") + + i2c_vc Set to "on" to enable the i2c interface + usually reserved for the VideoCore processor + (default "off") + + i2c An alias for i2c_arm + + i2c_arm_baudrate Set the baudrate of the ARM's i2c interface + (default "100000") + + i2c_vc_baudrate Set the baudrate of the VideoCore i2c interface + (default "100000") + + i2c_baudrate An alias for i2c_arm_baudrate + + i2s Set to "on" to enable the i2s interface + (default "off") + + krnbt Set to "on" to enable autoprobing of Bluetooth + driver without need of hciattach/btattach + (default "off") + + krnbt_baudrate Set the baudrate of the PL011 UART when used + with krnbt=on + + spi Set to "on" to enable the spi interfaces + (default "off") + + spi_dma4 Use to enable 40-bit DMA on spi interfaces + (the assigned value doesn't matter) + (2711 only) + + random Set to "on" to enable the hardware random + number generator (default "on") + + sd_overclock Clock (in MHz) to use when the MMC framework + requests 50MHz + + sd_poll_once Looks for a card once after booting. Useful + for network booting scenarios to avoid the + overhead of continuous polling. N.B. Using + this option restricts the system to using a + single card per boot (or none at all). + (default off) + + sd_force_pio Disable DMA support for SD driver (default off) + + sd_pio_limit Number of blocks above which to use DMA for + SD card (default 1) + + sd_debug Enable debug output from SD driver (default off) + + sdio_overclock Clock (in MHz) to use when the MMC framework + requests 50MHz for the SDIO/WLAN interface. + + tx_lpi_timer Set the delay in microseconds between going idle + and entering the low power state (default 600). + Requires EEE to be enabled - see "eee". + + uart0 Set to "off" to disable uart0 (default "on") + + uart1 Set to "on" or "off" to enable or disable uart1 + (default varies) + + watchdog Set to "on" to enable the hardware watchdog + (default "off") + + act_led_trigger Choose which activity the LED tracks. + Use "heartbeat" for a nice load indicator. + (default "mmc") + + act_led_activelow Set to "on" to invert the sense of the LED + (default "off") + N.B. For Pi 3B, 3B+, 3A+ and 4B, use the act-led + overlay. + + act_led_gpio Set which GPIO to use for the activity LED + (in case you want to connect it to an external + device) + (default "16" on a non-Plus board, "47" on a + Plus or Pi 2) + N.B. For Pi 3B, 3B+, 3A+ and 4B, use the act-led + overlay. + + pwr_led_trigger + pwr_led_activelow + pwr_led_gpio + As for act_led_*, but using the PWR LED. + Not available on Model A/B boards. + + N.B. It is recommended to only enable those interfaces that are needed. + Leaving all interfaces enabled can lead to unwanted behaviour (i2c_vc + interfering with Pi Camera, I2S and SPI hogging GPIO pins, etc.) + Note also that i2c, i2c_arm and i2c_vc are aliases for the physical + interfaces i2c0 and i2c1. Use of the numeric variants is still possible + but deprecated because the ARM/VC assignments differ between board + revisions. The same board-specific mapping applies to i2c_baudrate, + and the other i2c baudrate parameters. + + +Name: act-led +Info: Pi 3B, 3B+, 3A+ and 4B use a GPIO expander to drive the LEDs which can + only be accessed from the VPU. There is a special driver for this with a + separate DT node, which has the unfortunate consequence of breaking the + act_led_gpio and act_led_activelow dtparams. + This overlay changes the GPIO controller back to the standard one and + restores the dtparams. +Load: dtoverlay=act-led,= +Params: activelow Set to "on" to invert the sense of the LED + (default "off") + + gpio Set which GPIO to use for the activity LED + (in case you want to connect it to an external + device) + REQUIRED + + +Name: adafruit18 +Info: Overlay for the SPI-connected Adafruit 1.8" display (based on the + ST7735R chip). It includes support for the "green tab" version. +Load: dtoverlay=adafruit18,= +Params: green Use the adafruit18_green variant. + rotate Display rotation {0,90,180,270} + speed SPI bus speed in Hz (default 4000000) + fps Display frame rate in Hz + bgr Enable BGR mode (default off) + debug Debug output level {0-7} + dc_pin GPIO pin for D/C (default 24) + reset_pin GPIO pin for RESET (default 25) + led_pin GPIO used to control backlight (default 18) + + +Name: adau1977-adc +Info: Overlay for activation of ADAU1977 ADC codec over I2C for control + and I2S for data. +Load: dtoverlay=adau1977-adc +Params: + + +Name: adau7002-simple +Info: Overlay for the activation of ADAU7002 stereo PDM to I2S converter. +Load: dtoverlay=adau7002-simple,= +Params: card-name Override the default, "adau7002", card name. + + +Name: ads1015 +Info: Overlay for activation of Texas Instruments ADS1015 ADC over I2C +Load: dtoverlay=ads1015,= +Params: addr I2C bus address of device. Set based on how the + addr pin is wired. (default=0x48 assumes addr + is pulled to GND) + cha_enable Enable virtual channel a. (default=true) + cha_cfg Set the configuration for virtual channel a. + (default=4 configures this channel for the + voltage at A0 with respect to GND) + cha_datarate Set the datarate (samples/sec) for this channel. + (default=4 sets 1600 sps) + cha_gain Set the gain of the Programmable Gain + Amplifier for this channel. (default=2 sets the + full scale of the channel to 2.048 Volts) + + Channel (ch) parameters can be set for each enabled channel. + A maximum of 4 channels can be enabled (letters a thru d). + For more information refer to the device datasheet at: + http://www.ti.com/lit/ds/symlink/ads1015.pdf + + +Name: ads1115 +Info: Texas Instruments ADS1115 ADC +Load: dtoverlay=ads1115,[=] +Params: addr I2C bus address of device. Set based on how the + addr pin is wired. (default=0x48 assumes addr + is pulled to GND) + cha_enable Enable virtual channel a. + cha_cfg Set the configuration for virtual channel a. + (default=4 configures this channel for the + voltage at A0 with respect to GND) + cha_datarate Set the datarate (samples/sec) for this channel. + (default=7 sets 860 sps) + cha_gain Set the gain of the Programmable Gain + Amplifier for this channel. (Default 1 sets the + full scale of the channel to 4.096 Volts) + + Channel parameters can be set for each enabled channel. + A maximum of 4 channels can be enabled (letters a thru d). + For more information refer to the device datasheet at: + http://www.ti.com/lit/ds/symlink/ads1115.pdf + + +Name: ads7846 +Info: ADS7846 Touch controller +Load: dtoverlay=ads7846,= +Params: cs SPI bus Chip Select (default 1) + speed SPI bus speed (default 2MHz, max 3.25MHz) + penirq GPIO used for PENIRQ. REQUIRED + penirq_pull Set GPIO pull (default 0=none, 2=pullup) + swapxy Swap x and y axis + xmin Minimum value on the X axis (default 0) + ymin Minimum value on the Y axis (default 0) + xmax Maximum value on the X axis (default 4095) + ymax Maximum value on the Y axis (default 4095) + pmin Minimum reported pressure value (default 0) + pmax Maximum reported pressure value (default 65535) + xohms Touchpanel sensitivity (X-plate resistance) + (default 400) + + penirq is required and usually xohms (60-100) has to be set as well. + Apart from that, pmax (255) and swapxy are also common. + The rest of the calibration can be done with xinput-calibrator. + See: github.com/notro/fbtft/wiki/FBTFT-on-Raspian + Device Tree binding document: + www.kernel.org/doc/Documentation/devicetree/bindings/input/ads7846.txt + + +Name: adv7282m +Info: Analog Devices ADV7282M analogue video to CSI2 bridge. + Uses Unicam1, which is the standard camera connector on most Pi + variants. +Load: dtoverlay=adv7282m,= +Params: addr Overrides the I2C address (default 0x21) + + +Name: adv728x-m +Info: Analog Devices ADV728[0|1|2]-M analogue video to CSI2 bridges. + This is a wrapper for adv7282m, and defaults to ADV7282M. +Load: dtoverlay=adv728x-m,= +Params: addr Overrides the I2C address (default 0x21) + adv7280m Select ADV7280-M. + adv7281m Select ADV7281-M. + adv7281ma Select ADV7281-MA. + + +Name: akkordion-iqdacplus +Info: Configures the Digital Dreamtime Akkordion Music Player (based on the + OEM IQAudIO DAC+ or DAC Zero module). +Load: dtoverlay=akkordion-iqdacplus,= +Params: 24db_digital_gain Allow gain to be applied via the PCM512x codec + Digital volume control. Enable with + dtoverlay=akkordion-iqdacplus,24db_digital_gain + (The default behaviour is that the Digital + volume control is limited to a maximum of + 0dB. ie. it can attenuate but not provide + gain. For most users, this will be desired + as it will prevent clipping. By appending + the 24db_digital_gain parameter, the Digital + volume control will allow up to 24dB of + gain. If this parameter is enabled, it is the + responsibility of the user to ensure that + the Digital volume control is set to a value + that does not result in clipping/distortion!) + + +Name: allo-boss-dac-pcm512x-audio +Info: Configures the Allo Boss DAC audio cards. +Load: dtoverlay=allo-boss-dac-pcm512x-audio, +Params: 24db_digital_gain Allow gain to be applied via the PCM512x codec + Digital volume control. Enable with + "dtoverlay=allo-boss-dac-pcm512x-audio, + 24db_digital_gain" + (The default behaviour is that the Digital + volume control is limited to a maximum of + 0dB. ie. it can attenuate but not provide + gain. For most users, this will be desired + as it will prevent clipping. By appending + the 24db_digital_gain parameter, the Digital + volume control will allow up to 24dB of + gain. If this parameter is enabled, it is the + responsibility of the user to ensure that + the Digital volume control is set to a value + that does not result in clipping/distortion!) + slave Force Boss DAC into slave mode, using Pi a + master for bit clock and frame clock. Enable + with "dtoverlay=allo-boss-dac-pcm512x-audio, + slave" + + +Name: allo-boss2-dac-audio +Info: Configures the Allo Boss2 DAC audio card +Load: dtoverlay=allo-boss2-dac-audio +Params: + + +Name: allo-digione +Info: Configures the Allo Digione audio card +Load: dtoverlay=allo-digione +Params: + + +Name: allo-katana-dac-audio +Info: Configures the Allo Katana DAC audio card +Load: dtoverlay=allo-katana-dac-audio +Params: + + +Name: allo-piano-dac-pcm512x-audio +Info: Configures the Allo Piano DAC (2.0/2.1) audio cards. + (NB. This initial support is for 2.0 channel audio ONLY! ie. stereo. + The subwoofer outputs on the Piano 2.1 are not currently supported!) +Load: dtoverlay=allo-piano-dac-pcm512x-audio, +Params: 24db_digital_gain Allow gain to be applied via the PCM512x codec + Digital volume control. + (The default behaviour is that the Digital + volume control is limited to a maximum of + 0dB. ie. it can attenuate but not provide + gain. For most users, this will be desired + as it will prevent clipping. By appending + the 24db_digital_gain parameter, the Digital + volume control will allow up to 24dB of + gain. If this parameter is enabled, it is the + responsibility of the user to ensure that + the Digital volume control is set to a value + that does not result in clipping/distortion!) + + +Name: allo-piano-dac-plus-pcm512x-audio +Info: Configures the Allo Piano DAC (2.1) audio cards. +Load: dtoverlay=allo-piano-dac-plus-pcm512x-audio, +Params: 24db_digital_gain Allow gain to be applied via the PCM512x codec + Digital volume control. + (The default behaviour is that the Digital + volume control is limited to a maximum of + 0dB. ie. it can attenuate but not provide + gain. For most users, this will be desired + as it will prevent clipping. By appending + the 24db_digital_gain parameter, the Digital + volume control will allow up to 24dB of + gain. If this parameter is enabled, it is the + responsibility of the user to ensure that + the Digital volume control is set to a value + that does not result in clipping/distortion!) + glb_mclk This option is only with Kali board. If enabled, + MCLK for Kali is used and PLL is disabled for + better voice quality. (default Off) + + +Name: anyspi +Info: Universal device tree overlay for SPI devices + + Just specify the SPI address and device name ("compatible" property). + This overlay lacks any device-specific parameter support! + + For devices on spi1 or spi2, the interfaces should be enabled + with one of the spi1-1/2/3cs and/or spi2-1/2/3cs overlays. + + Examples: + 1. SPI NOR flash on spi0.1, maximum SPI clock frequency 45MHz: + dtoverlay=anyspi:spi0-1,dev="jedec,spi-nor",speed=45000000 + 2. MCP3204 ADC on spi1.2, maximum SPI clock frequency 500kHz: + dtoverlay=anyspi:spi1-2,dev="microchip,mcp3204" +Load: dtoverlay=anyspi,= +Params: spi- Configure device at spi, cs + (boolean, required) + dev Set device name to search compatible module + (string, required) + speed Set SPI clock frequency in Hz + (integer, optional, default 500000) + + +Name: apds9960 +Info: Configures the AVAGO APDS9960 digital proximity, ambient light, RGB and + gesture sensor +Load: dtoverlay=apds9960,= +Params: gpiopin GPIO used for INT (default 4) + noints Disable the interrupt GPIO line. + + +Name: applepi-dac +Info: Configures the Orchard Audio ApplePi-DAC audio card +Load: dtoverlay=applepi-dac +Params: + + +Name: at86rf233 +Info: Configures the Atmel AT86RF233 802.15.4 low-power WPAN transceiver, + connected to spi0.0 +Load: dtoverlay=at86rf233,= +Params: interrupt GPIO used for INT (default 23) + reset GPIO used for Reset (default 24) + sleep GPIO used for Sleep (default 25) + speed SPI bus speed in Hz (default 3000000) + trim Fine tuning of the internal capacitance + arrays (0=+0pF, 15=+4.5pF, default 15) + + +Name: audioinjector-addons +Info: Configures the audioinjector.net audio add on soundcards +Load: dtoverlay=audioinjector-addons,= +Params: non-stop-clocks Keeps the clocks running even when the stream + is paused or stopped (default off) + + +Name: audioinjector-isolated-soundcard +Info: Configures the audioinjector.net isolated soundcard +Load: dtoverlay=audioinjector-isolated-soundcard +Params: + + +Name: audioinjector-ultra +Info: Configures the audioinjector.net ultra soundcard +Load: dtoverlay=audioinjector-ultra +Params: + + +Name: audioinjector-wm8731-audio +Info: Configures the audioinjector.net audio add on soundcard +Load: dtoverlay=audioinjector-wm8731-audio +Params: + + +Name: audiosense-pi +Info: Configures the audiosense-pi add on soundcard + For more information refer to + https://gitlab.com/kakar0t/audiosense-pi +Load: dtoverlay=audiosense-pi +Params: + + +Name: audremap +Info: Switches PWM sound output to GPIOs on the 40-pin header +Load: dtoverlay=audremap,= +Params: swap_lr Reverse the channel allocation, which will also + swap the audio jack outputs (default off) + enable_jack Don't switch off the audio jack output + (default off) + pins_12_13 Select GPIOs 12 & 13 (default) + pins_18_19 Select GPIOs 18 & 19 + + +Name: balena-fin +Info: Overlay that enables WLAN, Bluetooth and the GPIO expander on the + balenaFin carrier board for the Raspberry Pi Compute Module 3/3+ Lite. +Load: dtoverlay=balena-fin +Params: + + +Name: bmp085_i2c-sensor +Info: This overlay is now deprecated - see i2c-sensor +Load: + + +Name: cap1106 +Info: Enables the ability to use the cap1106 touch sensor as a keyboard +Load: dtoverlay=cap1106,= +Params: int_pin GPIO pin for interrupt signal (default 23) + + +Name: chipdip-dac +Info: Configures Chip Dip audio cards. +Load: dtoverlay=chipdip-dac +Params: + + +Name: cma +Info: Set custom CMA sizes, only use if you know what you are doing, might + clash with other overlays like vc4-fkms-v3d and vc4-kms-v3d. +Load: dtoverlay=cma,= +Params: cma-512 CMA is 512MB (needs 1GB) + cma-448 CMA is 448MB (needs 1GB) + cma-384 CMA is 384MB (needs 1GB) + cma-320 CMA is 320MB (needs 1GB) + cma-256 CMA is 256MB (needs 1GB) + cma-192 CMA is 192MB (needs 1GB) + cma-128 CMA is 128MB + cma-96 CMA is 96MB + cma-64 CMA is 64MB + cma-size CMA size in bytes, 4MB aligned + cma-default Use upstream's default value + + +Name: dht11 +Info: Overlay for the DHT11/DHT21/DHT22 humidity/temperature sensors + Also sometimes found with the part number(s) AM230x. +Load: dtoverlay=dht11,= +Params: gpiopin GPIO connected to the sensor's DATA output. + (default 4) + + +Name: dionaudio-loco +Info: Configures the Dion Audio LOCO DAC-AMP +Load: dtoverlay=dionaudio-loco +Params: + + +Name: dionaudio-loco-v2 +Info: Configures the Dion Audio LOCO-V2 DAC-AMP +Load: dtoverlay=dionaudio-loco-v2,= +Params: 24db_digital_gain Allow gain to be applied via the PCM512x codec + Digital volume control. Enable with + "dtoverlay=hifiberry-dacplus,24db_digital_gain" + (The default behaviour is that the Digital + volume control is limited to a maximum of + 0dB. ie. it can attenuate but not provide + gain. For most users, this will be desired + as it will prevent clipping. By appending + the 24dB_digital_gain parameter, the Digital + volume control will allow up to 24dB of + gain. If this parameter is enabled, it is the + responsibility of the user to ensure that + the Digital volume control is set to a value + that does not result in clipping/distortion!) + + +Name: disable-bt +Info: Disable onboard Bluetooth on Pi 3B, 3B+, 3A+, 4B and Zero W, restoring + UART0/ttyAMA0 over GPIOs 14 & 15. + N.B. To disable the systemd service that initialises the modem so it + doesn't use the UART, use 'sudo systemctl disable hciuart'. +Load: dtoverlay=disable-bt +Params: + + +Name: disable-wifi +Info: Disable onboard WLAN on Pi 3B, 3B+, 3A+, 4B and Zero W. +Load: dtoverlay=disable-wifi +Params: + + +Name: dpi18 +Info: Overlay for a generic 18-bit DPI display + This uses GPIOs 0-21 (so no I2C, uart etc.), and activates the output + 2-3 seconds after the kernel has started. +Load: dtoverlay=dpi18 +Params: + + +Name: dpi18cpadhi +Info: Overlay for a generic 18-bit DPI display (in 'mode 6' connection scheme) + This uses GPIOs 0-9,12-17,20-25 (so no I2C, uart etc.), and activates + the output 3-3 seconds after the kernel has started. +Load: dtoverlay=dpi18cpadhi +Params: + + +Name: dpi24 +Info: Overlay for a generic 24-bit DPI display + This uses GPIOs 0-27 (so no I2C, uart etc.), and activates the output + 2-3 seconds after the kernel has started. +Load: dtoverlay=dpi24 +Params: + + +Name: draws +Info: Configures the NW Digital Radio DRAWS Hat + + The board includes an ADC to measure various board values and also + provides two analog user inputs on the expansion header. The ADC + can be configured for various sample rates and gain values to adjust + the input range. Tables describing the two parameters follow. + + ADC Gain Values: + 0 = +/- 6.144V + 1 = +/- 4.096V + 2 = +/- 2.048V + 3 = +/- 1.024V + 4 = +/- 0.512V + 5 = +/- 0.256V + 6 = +/- 0.256V + 7 = +/- 0.256V + + ADC Datarate Values: + 0 = 128sps + 1 = 250sps + 2 = 490sps + 3 = 920sps + 4 = 1600sps (default) + 5 = 2400sps + 6 = 3300sps + 7 = 3300sps +Load: dtoverlay=draws,= +Params: draws_adc_ch4_gain Sets the full scale resolution of the ADCs + input voltage sensor (default 1) + + draws_adc_ch4_datarate Sets the datarate of the ADCs input voltage + sensor + + draws_adc_ch5_gain Sets the full scale resolution of the ADCs + 5V rail voltage sensor (default 1) + + draws_adc_ch5_datarate Sets the datarate of the ADCs 4V rail voltage + sensor + + draws_adc_ch6_gain Sets the full scale resolution of the ADCs + AIN2 input (default 2) + + draws_adc_ch6_datarate Sets the datarate of the ADCs AIN2 input + + draws_adc_ch7_gain Sets the full scale resolution of the ADCs + AIN3 input (default 2) + + draws_adc_ch7_datarate Sets the datarate of the ADCs AIN3 input + + alsaname Name of the ALSA audio device (default "draws") + + +Name: dwc-otg +Info: Selects the dwc_otg USB controller driver which has fiq support. This + is the default on all except the Pi Zero which defaults to dwc2. +Load: dtoverlay=dwc-otg +Params: + + +Name: dwc2 +Info: Selects the dwc2 USB controller driver +Load: dtoverlay=dwc2,= +Params: dr_mode Dual role mode: "host", "peripheral" or "otg" + + g-rx-fifo-size Size of rx fifo size in gadget mode + + g-np-tx-fifo-size Size of non-periodic tx fifo size in gadget + mode + + +[ The ds1307-rtc overlay has been deleted. See i2c-rtc. ] + + +Name: edt-ft5406 +Info: Overlay for the EDT FT5406 touchscreen on the CSI/DSI I2C interface. + This works with the Raspberry Pi 7" touchscreen when not being polled + by the firmware. + You MUST use either "disable_touchscreen=1" or "ignore_lcd=1" in + config.txt to stop the firmware polling the touchscreen. +Load: dtoverlay=edt-ft5406,= +Params: sizex Touchscreen size x (default 800) + sizey Touchscreen size y (default 480) + invx Touchscreen inverted x axis + invy Touchscreen inverted y axis + swapxy Touchscreen swapped x y axis + + +Name: enc28j60 +Info: Overlay for the Microchip ENC28J60 Ethernet Controller on SPI0 +Load: dtoverlay=enc28j60,= +Params: int_pin GPIO used for INT (default 25) + + speed SPI bus speed (default 12000000) + + +Name: enc28j60-spi2 +Info: Overlay for the Microchip ENC28J60 Ethernet Controller on SPI2 +Load: dtoverlay=enc28j60-spi2,= +Params: int_pin GPIO used for INT (default 39) + + speed SPI bus speed (default 12000000) + + +Name: exc3000 +Info: Enables I2C connected EETI EXC3000 multiple touch controller using + GPIO 4 (pin 7 on GPIO header) for interrupt. +Load: dtoverlay=exc3000,= +Params: interrupt GPIO used for interrupt (default 4) + sizex Touchscreen size x (default 4096) + sizey Touchscreen size y (default 4096) + invx Touchscreen inverted x axis + invy Touchscreen inverted y axis + swapxy Touchscreen swapped x y axis + + +Name: fe-pi-audio +Info: Configures the Fe-Pi Audio Sound Card +Load: dtoverlay=fe-pi-audio +Params: + + +Name: fsm-demo +Info: A demonstration of the gpio-fsm driver. The GPIOs are chosen to work + nicely with a "traffic-light" display of red, amber and green LEDs on + GPIOs 7, 8 and 25 respectively. +Load: dtoverlay=fsm-demo,= +Params: fsm_debug Enable debug logging (default off) + + +Name: ghost-amp +Info: An overlay for the Ghost amplifier. +Load: dtoverlay=ghost-amp,= +Params: fsm_debug Enable debug logging of the GPIO FSM (default + off) + + +Name: goodix +Info: Enables I2C connected Goodix gt9271 multiple touch controller using + GPIOs 4 and 17 (pins 7 and 11 on GPIO header) for interrupt and reset. +Load: dtoverlay=goodix,= +Params: interrupt GPIO used for interrupt (default 4) + reset GPIO used for reset (default 17) + + +Name: googlevoicehat-soundcard +Info: Configures the Google voiceHAT soundcard +Load: dtoverlay=googlevoicehat-soundcard +Params: + + +Name: gpio-fan +Info: Configure a GPIO pin to control a cooling fan. +Load: dtoverlay=gpio-fan,= +Params: gpiopin GPIO used to control the fan (default 12) + temp Temperature at which the fan switches on, in + millicelcius (default 55000) + + +Name: gpio-ir +Info: Use GPIO pin as rc-core style infrared receiver input. The rc-core- + based gpio_ir_recv driver maps received keys directly to a + /dev/input/event* device, all decoding is done by the kernel - LIRC is + not required! The key mapping and other decoding parameters can be + configured by "ir-keytable" tool. +Load: dtoverlay=gpio-ir,= +Params: gpio_pin Input pin number. Default is 18. + + gpio_pull Desired pull-up/down state (off, down, up) + Default is "up". + + invert "1" = invert the input (active-low signalling). + "0" = non-inverted input (active-high + signalling). Default is "1". + + rc-map-name Default rc keymap (can also be changed by + ir-keytable), defaults to "rc-rc6-mce" + + +Name: gpio-ir-tx +Info: Use GPIO pin as bit-banged infrared transmitter output. + This is an alternative to "pwm-ir-tx". gpio-ir-tx doesn't require + a PWM so it can be used together with onboard analog audio. +Load: dtoverlay=gpio-ir-tx,= +Params: gpio_pin Output GPIO (default 18) + + invert "1" = invert the output (make it active-low). + Default is "0" (active-high). + + +Name: gpio-key +Info: This is a generic overlay for activating GPIO keypresses using + the gpio-keys library and this dtoverlay. Multiple keys can be + set up using multiple calls to the overlay for configuring + additional buttons or joysticks. You can see available keycodes + at https://github.com/torvalds/linux/blob/v4.12/include/uapi/ + linux/input-event-codes.h#L64 +Load: dtoverlay=gpio-key,= +Params: gpio GPIO pin to trigger on (default 3) + active_low When this is 1 (active low), a falling + edge generates a key down event and a + rising edge generates a key up event. + When this is 0 (active high), this is + reversed. The default is 1 (active low) + gpio_pull Desired pull-up/down state (off, down, up) + Default is "up". Note that the default pin + (GPIO3) has an external pullup + label Set a label for the key + keycode Set the key code for the button + + + +Name: gpio-led +Info: This is a generic overlay for activating LEDs (or any other component) + by a GPIO pin. Multiple LEDs can be set up using multiple calls to the + overlay. While there are many existing methods to activate LEDs on the + RPi, this method offers some advantages: + 1) Does not require any userspace programs. + 2) LEDs can be connected to the kernel's led-trigger framework, + and drive the LED based on triggers such as cpu load, heartbeat, + kernel panic, key input, timers and others. + 3) LED can be tied to the input state of another GPIO pin. + 4) The LED is setup early during the kernel boot process (useful + for cpu/heartbeat/panic triggers). + + Typical electrical connection is: + RPI-GPIO.19 -> LED -> 300ohm resister -> RPI-GND + The GPIO pin number can be changed with the 'gpio=' parameter. + + To control an LED from userspace, write a 0 or 1 value: + echo 1 > /sys/class/leds/myled1/brightness + The 'myled1' name can be changed with the 'label=' parameter. + + To connect the LED to a kernel trigger from userspace: + echo cpu > /sys/class/leds/myled1/trigger + echo heartbeat > /sys/class/leds/myled1/trigger + echo none > /sys/class/leds/myled1/trigger + To connect the LED to GPIO.26 pin (physical pin 37): + echo gpio > /sys/class/leds/myled1/trigger + echo 26 > /sys/class/leds/myled1/gpio + Available triggers: + cat /sys/class/leds/myled1/trigger + + More information about the Linux kernel LED/Trigger system: + https://www.kernel.org/doc/Documentation/leds/leds-class.rst + https://www.kernel.org/doc/Documentation/leds/ledtrig-oneshot.rst +Load: dtoverlay=gpio-led,= +Params: gpio GPIO pin connected to the LED (default 19) + label The label for this LED. It will appear under + /sys/class/leds/