commit 6cca13de26eea6d32a98d96d916a048d16a12822 upstream.
Fix the circular lock dependency and unbalanced unlock of addess0_mutex
introduced when fixing an address0_mutex enumeration retry race in commit
ae6dc22d2d1 ("usb: hub: Fix usb enumeration issue due to address0 race")
Make sure locking order between port_dev->status_lock and address0_mutex
is correct, and that address0_mutex is not unlocked in hub_port_connect
"done:" codepath which may be reached without locking address0_mutex
Fixes: 6ae6dc22d2d1 ("usb: hub: Fix usb enumeration issue due to address0 race")
Cc: <stable@vger.kernel.org>
Reported-by: Marek Szyprowski <m.szyprowski@samsung.com>
Tested-by: Hans de Goede <hdegoede@redhat.com>
Tested-by: Marek Szyprowski <m.szyprowski@samsung.com>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20211123101656.1113518-1-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 6ae6dc22d2d1ce6aa77a6da8a761e61aca216f8b upstream.
xHC hardware can only have one slot in default state with address 0
waiting for a unique address at a time, otherwise "undefined behavior
may occur" according to xhci spec 5.4.3.4
The address0_mutex exists to prevent this across both xhci roothubs.
If hub_port_init() fails, it may unlock the mutex and exit with a xhci
slot in default state. If the other xhci roothub calls hub_port_init()
at this point we end up with two slots in default state.
Make sure the address0_mutex protects the slot default state across
hub_port_init() retries, until slot is addressed or disabled.
Note, one known minor case is not fixed by this patch.
If device needs to be reset during resume, but fails all hub_port_init()
retries in usb_reset_and_verify_device(), then it's possible the slot is
still left in default state when address0_mutex is unlocked.
Cc: <stable@vger.kernel.org>
Fixes: 638139eb95 ("usb: hub: allow to process more usb hub events in parallel")
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20211115221630.871204-1-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 362468830dd5bea8bf6ad5203b2ea61f8a4e8288 upstream.
The code that enables either BC_LVL or COMP_CHNG interrupt in tcpm_set_cc
wrongly assumes that the interrupt is unmasked by writing 1 to the apropriate
bit in the mask register. In fact, interrupts are enabled when the mask
is 0, so the tcpm_set_cc enables interrupt for COMP_CHNG when it expects
BC_LVL interrupt to be enabled.
This causes inability of the driver to recognize cable unplug events
in host mode (unplug is recognized only via a COMP_CHNG interrupt).
In device mode this bug was masked by simultaneous triggering of the VBUS
change interrupt, because of loss of VBUS when the port peer is providing
power.
Fixes: 48242e3053 ("usb: typec: fusb302: Revert "Resolve fixed power role contract setup"")
Cc: stable <stable@vger.kernel.org>
Cc: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Ondrej Jirman <megous@megous.com>
Link: https://lore.kernel.org/r/20211108102833.2793803-1-megous@megous.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit d4d2e5329ae9dfd6742c84d79f7d143d10410f1b upstream.
If the first call to devm_usb_get_phy_by_phandle(dev, "fsl,usbphy", 0)
fails with something other than -ENODEV then it leads to an error
pointer dereference. For those errors we should just jump directly to
the error handling.
Fixes: 8253a34bfa ("usb: chipidea: ci_hdrc_imx: Also search for 'phys' phandle")
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Link: https://lore.kernel.org/r/20211117074923.GF5237@kili
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 26288448120b28af1dfd85a6fa6b6d55a16c7f2f upstream.
In the endpoint interrupt functions
dwc3_gadget_endpoint_transfer_in_progress() and
dwc3_gadget_endpoint_trbs_complete() will dereference the endpoint
descriptor. But it could be cleared in __dwc3_gadget_ep_disable()
when accessory disconnected. So we need to check whether it is null
or not before dereferencing it.
Fixes: f09ddcfcb8 ("usb: dwc3: gadget: Prevent EP queuing while stopping transfers")
Cc: stable <stable@vger.kernel.org>
Reviewed-by: Jack Pham <quic_jackp@quicinc.com>
Signed-off-by: Albert Wang <albertccwang@google.com>
Link: https://lore.kernel.org/r/20211109092642.3507692-1-albertccwang@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 63c4c320ccf77074ffe9019ac596603133c1b517 upstream.
The programming guide noted that the driver needs to verify if the link
state is in U0 before executing the Start Transfer command. If it's not
in U0, the driver needs to perform remote wakeup. This is not accurate.
If the link state is in U1/U2, then the controller will not respond to
link recovery request from DCTL.ULSTCHNGREQ. The Start Transfer command
will trigger a link recovery if it is in U1/U2. A clarification will be
added to the programming guide for all controller versions.
The current implementation shouldn't cause any functional issue. It may
occasionally report an invalid time out warning from failed link
recovery request. The driver will still go ahead with the Start Transfer
command if the remote wakeup fails. The new change only initiates remote
wakeup where it is needed, which is when the link state is in L1/L2/U3.
Fixes: c36d8e947a ("usb: dwc3: gadget: put link to U0 before Start Transfer")
Cc: <stable@vger.kernel.org>
Signed-off-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Link: https://lore.kernel.org/r/05b4a5fbfbd0863fc9b1d7af934a366219e3d0b4.1635204761.git.Thinh.Nguyen@synopsys.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit d74dc3e9f58c28689cef1faccf918e06587367d3 upstream.
The End Transfer command from a stream endpoint will generate a NoStream
event, and we should ignore it. Currently we set the flag
DWC3_EP_IGNORE_NEXT_NOSTREAM to track this prior to sending the command,
and it will be cleared on the next stream event. However, a stream event
may be generated before the End Transfer command completion and
prematurely clear the flag. Fix this by setting the flag on End Transfer
completion instead.
Fixes: 140ca4cfea ("usb: dwc3: gadget: Handle stream transfers")
Cc: <stable@vger.kernel.org>
Signed-off-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Link: https://lore.kernel.org/r/cee1253af4c3600edb878d11c9c08b040817ae23.1635203975.git.Thinh.Nguyen@synopsys.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 310780e825f3ffd211b479b8f828885a6faedd63 upstream.
A new commit in LLVM causes an error on the use of 'long double' when
'-mno-x87' is used, which the kernel does through an alias,
'-mno-80387' (see the LLVM commit below for more details around why it
does this).
drivers/usb/dwc2/hcd_queue.c:1744:25: error: expression requires 'long double' type support, but target 'x86_64-unknown-linux-gnu' does not support it
delay = ktime_set(0, DWC2_RETRY_WAIT_DELAY);
^
drivers/usb/dwc2/hcd_queue.c:62:34: note: expanded from macro 'DWC2_RETRY_WAIT_DELAY'
#define DWC2_RETRY_WAIT_DELAY (1 * 1E6L)
^
1 error generated.
This happens due to the use of a 'long double' literal. The 'E6' part of
'1E6L' causes the literal to be a 'double' then the 'L' suffix promotes
it to 'long double'.
There is no visible reason for a floating point value in this driver, as
the value is only used as a parameter to a function that expects an
integer type. Use NSEC_PER_MSEC, which is the same integer value as
'1E6L', to avoid changing functionality but fix the error.
Link: https://github.com/ClangBuiltLinux/linux/issues/1497
Link: a8083d42b1
Fixes: 6ed30a7d8e ("usb: dwc2: host: use hrtimer for NAK retries")
Cc: stable <stable@vger.kernel.org>
Reviewed-by: Nick Desaulniers <ndesaulniers@google.com>
Reviewed-by: John Keeping <john@metanate.com>
Acked-by: Minas Harutyunyan <Minas.Harutyunyan@synopsys.com>
Signed-off-by: Nathan Chancellor <nathan@kernel.org>
Link: https://lore.kernel.org/r/20211105145802.2520658-1-nathan@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 7ad4a0b1d46b2612f4429a72afd8f137d7efa9a9 upstream.
Added updating of request frame number for elapsed frames,
otherwise frame number will remain as previous use of request.
This will allow function driver to correctly track frames in
case of Missed ISOC occurs.
Added setting request actual length to 0 for elapsed frames.
In Slave mode when pushing data to RxFIFO by dwords, request
actual length incrementing accordingly. But before whole packet
will be pushed into RxFIFO and send to host can occurs Missed
ISOC and data will not send to host. So, in this case request
actual length should be reset to 0.
Fixes: 91bb163e1e ("usb: dwc2: gadget: Fix ISOC flow for BDMA and Slave")
Cc: stable <stable@vger.kernel.org>
Reviewed-by: John Keeping <john@metanate.com>
Signed-off-by: Minas Harutyunyan <Minas.Harutyunyan@synopsys.com>
Link: https://lore.kernel.org/r/c356baade6e9716d312d43df08d53ae557cb8037.1636011277.git.Minas.Harutyunyan@synopsys.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit fc153aba3ef371d0d76eb88230ed4e0dee5b38f2 upstream.
Instead of maintaining a single-linked list of devices that must be
searched linearly in .remove() just use spi_set_drvdata() to remember the
link between the spi device and the driver struct. Then the global list
and the next member can be dropped.
This simplifies the driver, reduces the memory footprint and the time to
search the list. Also it makes obvious that there is always a corresponding
driver struct for a given device in .remove(), so the error path for
!max3421_hcd can be dropped, too.
As a side effect this fixes a data inconsistency when .probe() races with
itself for a second max3421 device in manipulating max3421_hcd_list. A
similar race is fixed in .remove(), too.
Fixes: 2d53139f31 ("Add support for using a MAX3421E chip as a host driver.")
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Link: https://lore.kernel.org/r/20211018204028.2914597-1-u.kleine-koenig@pengutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 876a75cb520f5869533a30a6ca01545ec817b7a0 ]
Some functions may dynamically enable and disable their endpoints
regularly throughout their operation, particularly when Set Interface
is employed to switch between Alternate Settings. For instance the
UAC2 function has its respective endpoints for playback & capture
associated with AltSetting 1, in which case those endpoints would not
get enabled until the host activates the AltSetting. And they
conversely become disabled when the interfaces' AltSetting 0 is
chosen.
With the DWC3 FIFO resizing algorithm recently added, every
usb_ep_enable() call results in a call to resize that EP's TXFIFO,
but if the same endpoint is enabled again and again, this incorrectly
leads to FIFO RAM allocation exhaustion as the mechanism did not
account for the possibility that endpoints can be re-enabled many
times.
Example log splat:
dwc3 a600000.dwc3: Fifosize(3717) > RAM size(3462) ep3in depth:217973127
configfs-gadget gadget: u_audio_start_capture:521 Error!
dwc3 a600000.dwc3: request 000000000be13e18 was not queued to ep3in
Add another bit DWC3_EP_TXFIFO_RESIZED to dep->flags to keep track of
whether an EP had already been resized in the current configuration.
If so, bail out of dwc3_gadget_resize_tx_fifos() to avoid the
calculation error resulting from accumulating the EP's FIFO depth
repeatedly. This flag is retained across multiple ep_disable() and
ep_enable() calls and is cleared when GTXFIFOSIZn is reset in
dwc3_gadget_clear_tx_fifos() upon receiving the next Set Config.
Fixes: 9f607a309f ("usb: dwc3: Resize TX FIFOs to meet EP bursting requirements")
Reviewed-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Signed-off-by: Jack Pham <jackp@codeaurora.org>
Link: https://lore.kernel.org/r/20211021180129.27938-1-jackp@codeaurora.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 1ad707f559f7cb12c64f3d7cb37f0b1ea27c1058 ]
If role is changed without the "none" step, A- and B- valid session could
be set at the same time. It is an issue.
This patch resets A-session if role switch sets B-session, and resets
B-session if role switch sets A-session.
Then, it is possible to change the role without the "none" step.
Fixes: 17f934024e ("usb: dwc2: override PHY input signals with usb role switch support")
Acked-by: Minas Harutyunyan <Minas.Harutyunyan@synopsys.com>
Signed-off-by: Amelie Delaunay <amelie.delaunay@foss.st.com>
Link: https://lore.kernel.org/r/20211005095305.66397-4-amelie.delaunay@foss.st.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 8d387f61b0240854e81450c261beb775065bad5d ]
In case of USB_DR_MODE_PERIPHERAL, the OTG clock is disabled at the end of
the probe (it is not the case if USB_DR_MODE_HOST or USB_DR_MODE_OTG).
The clock is then enabled on udc_start.
If dwc2_drd_role_sw_set is called before udc_start (it is the case if the
usb cable is plugged at boot), GOTGCTL and GUSBCFG registers cannot be
read/written, so session cannot be overridden.
To avoid this case, check the ll_hw_enabled value and enable the clock if
it is available, and disable it after the override.
Fixes: 17f934024e ("usb: dwc2: override PHY input signals with usb role switch support")
Acked-by: Minas Harutyunyan <Minas.Harutyunyan@synopsys.com>
Signed-off-by: Amelie Delaunay <amelie.delaunay@foss.st.com>
Link: https://lore.kernel.org/r/20211005095305.66397-3-amelie.delaunay@foss.st.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b2cab2a24fb5d13ce1d384ecfb6de827fa08a048 ]
Instead of forcing the role to Device, check the dr_mode configuration.
If the core is Host only, force the mode to Host, this to avoid the
dwc2_force_mode warning:
WARNING: CPU: 1 PID: 21 at drivers/usb/dwc2/core.c:615 dwc2_drd_init+0x104/0x17c
When forcing mode to Host, dwc2_force_mode may sleep the time the host
role is applied. To avoid sleeping while atomic context, move the call
to dwc2_force_mode after spin_unlock_irqrestore. It is safe, as
interrupts are not yet unmasked here.
Fixes: 17f934024e ("usb: dwc2: override PHY input signals with usb role switch support")
Acked-by: Minas Harutyunyan <Minas.Harutyunyan@synopsys.com>
Signed-off-by: Amelie Delaunay <amelie.delaunay@foss.st.com>
Link: https://lore.kernel.org/r/20211005095305.66397-2-amelie.delaunay@foss.st.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 9aaa81c3366e8393a62374e3a1c67c69edc07b8a upstream.
Chipidea core was calling the interrupt handler from non-IRQ context
with interrupts enabled, something which can lead to a deadlock if
there's an actual interrupt trying to take a lock that's already held
(e.g. the controller lock in udc_irq()).
Add a wrapper that can be used to fake interrupts instead of calling the
handler directly.
Fixes: 3ecb3e09b0 ("usb: chipidea: Use extcon framework for VBUS and ID detect")
Fixes: 876d4e1e82 ("usb: chipidea: core: add wakeup support for extcon")
Cc: Peter Chen <peter.chen@kernel.org>
Cc: stable@vger.kernel.org # 4.4
Signed-off-by: Johan Hovold <johan@kernel.org>
Link: https://lore.kernel.org/r/20211021083447.20078-1-johan@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit e1959faf085b004e6c3afaaaa743381f00e7c015 upstream.
Some USB 3.1 enumeration issues were reported after the hub driver removed
the minimum 100ms limit for the power-on-good delay.
Since commit 90d28fb53d ("usb: core: reduce power-on-good delay time of
root hub") the hub driver sets the power-on-delay based on the
bPwrOn2PwrGood value in the hub descriptor.
xhci driver has a 20ms bPwrOn2PwrGood value for both roothubs based
on xhci spec section 5.4.8, but it's clearly not enough for the
USB 3.1 devices, causing enumeration issues.
Tests indicate full 100ms delay is needed.
Reported-by: Walt Jr. Brake <mr.yming81@gmail.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Fixes: 90d28fb53d ("usb: core: reduce power-on-good delay time of root hub")
Cc: stable <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20211105160036.549516-1-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 21b5fcdccb32ff09b6b63d4a83c037150665a83f upstream.
musb_gadget_queue() adds the passed request to musb_ep::req_list. If the
endpoint is idle and it is the first request then it invokes
musb_queue_resume_work(). If the function returns an error then the
error is passed to the caller without any clean-up and the request
remains enqueued on the list. If the caller enqueues the request again
then the list corrupts.
Remove the request from the list on error.
Fixes: ea2f35c01d ("usb: musb: Fix sleeping function called from invalid context for hdrc glue")
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Viraj Shah <viraj.shah@linutronix.de>
Link: https://lore.kernel.org/r/20211021093644.4734-1-viraj.shah@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit a0548b26901f082684ad1fb3ba397d2de3a1406a upstream.
On 64-bit:
drivers/usb/gadget/udc/fsl_qe_udc.c: In function ‘qe_ep0_rx’:
drivers/usb/gadget/udc/fsl_qe_udc.c:842:13: error: cast from pointer to integer of different size [-Werror=pointer-to-int-cast]
842 | vaddr = (u32)phys_to_virt(in_be32(&bd->buf));
| ^
In file included from drivers/usb/gadget/udc/fsl_qe_udc.c:41:
drivers/usb/gadget/udc/fsl_qe_udc.c:843:28: error: cast to pointer from integer of different size [-Werror=int-to-pointer-cast]
843 | frame_set_data(pframe, (u8 *)vaddr);
| ^
The driver assumes physical and virtual addresses are 32-bit, hence it
cannot work on 64-bit platforms.
Acked-by: Li Yang <leoyang.li@nxp.com>
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Link: https://lore.kernel.org/r/20211027080849.3276289-1-geert@linux-m68k.org
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Johan writes:
USB-serial fixes for 5.15-rc6
Here are some new modem device ids.
All have been in linux-next with no reported issues.
* tag 'usb-serial-5.15-rc6' of https://git.kernel.org/pub/scm/linux/kernel/git/johan/usb-serial:
USB: serial: qcserial: add EM9191 QDL support
USB: serial: option: add Quectel EC200S-CN module support
USB: serial: option: add prod. id for Quectel EG91
USB: serial: option: add Telit LE910Cx composition 0x1204
Commit 7c75bde329 ("usb: musb: musb_dsps: request_irq() after
initializing musb") has inverted the calls to
dsps_setup_optional_vbus_irq() and dsps_create_musb_pdev() without
updating correctly the error path. dsps_create_musb_pdev() allocates and
registers a new platform device which must be unregistered and freed
with platform_device_unregister(), and this is missing upon
dsps_setup_optional_vbus_irq() error.
While on the master branch it seems not to trigger any issue, I observed
a kernel crash because of a NULL pointer dereference with a v5.10.70
stable kernel where the patch mentioned above was backported. With this
kernel version, -EPROBE_DEFER is returned the first time
dsps_setup_optional_vbus_irq() is called which triggers the probe to
error out without unregistering the platform device. Unfortunately, on
the Beagle Bone Black Wireless, the platform device still living in the
system is being used by the USB Ethernet gadget driver, which during the
boot phase triggers the crash.
My limited knowledge of the musb world prevents me to revert this commit
which was sent to silence a robot warning which, as far as I understand,
does not make sense. The goal of this patch was to prevent an IRQ to
fire before the platform device being registered. I think this cannot
ever happen due to the fact that enabling the interrupts is done by the
->enable() callback of the platform musb device, and this platform
device must be already registered in order for the core or any other
user to use this callback.
Hence, I decided to fix the error path, which might prevent future
errors on mainline kernels while also fixing older ones.
Fixes: 7c75bde329 ("usb: musb: musb_dsps: request_irq() after initializing musb")
Cc: stable@vger.kernel.org
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/r/20211005221631.1529448-1-miquel.raynal@bootlin.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The command ring pointer is located at [6:63] bits of the command
ring control register (CRCR). All the control bits like command stop,
abort are located at [0:3] bits. While aborting a command, we read the
CRCR and set the abort bit and write to the CRCR. The read will always
give command ring pointer as all zeros. So we essentially write only
the control bits. Since we split the 64 bit write into two 32 bit writes,
there is a possibility of xHC command ring stopped before the upper
dword (all zeros) is written. If that happens, xHC updates the upper
dword of its internal command ring pointer with all zeros. Next time,
when the command ring is restarted, we see xHC memory access failures.
Fix this issue by only writing to the lower dword of CRCR where all
control bits are located.
Cc: stable@vger.kernel.org
Signed-off-by: Pavankumar Kondeti <pkondeti@codeaurora.org>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20211008092547.3996295-5-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Pull USB fixes from Greg KH:
"Here are some small USB fixes for 5.15-rc5 that resolve a number of
reported issues:
- gadget driver fixes
- xhci build warning fixes
- build configuration fix
- cdc-acm tty handling fixes
- cdc-wdm fix
- typec fixes
All of these have been in linux-next for a while with no reported
issues"
* tag 'usb-5.15-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb:
USB: cdc-acm: fix break reporting
USB: cdc-acm: fix racy tty buffer accesses
usb: gadget: f_uac2: fixed EP-IN wMaxPacketSize
usb: cdc-wdm: Fix check for WWAN
usb: chipidea: ci_hdrc_imx: Also search for 'phys' phandle
usb: typec: tcpm: handle SRC_STARTUP state if cc changes
usb: typec: tcpci: don't handle vSafe0V event if it's not enabled
usb: typec: tipd: Remove dependency on "connector" child fwnode
Partially revert "usb: Kconfig: using select for USB_COMMON dependency"
usb: dwc3: gadget: Revert "set gadgets parent to the right controller"
usb: xhci: tegra: mark PM functions as __maybe_unused
Pull ARM SoC fixes from Arnd Bergmann:
"This is a larger than normal update for Arm SoC specific code, most of
it in device trees, but also drivers and the omap and at91/sama7
platforms:
- There are four new entries to the MAINTAINERS file: Sven Peter and
Alyssa Rosenzweig for Apple M1, Romain Perier for Mstar/sigmastar,
and Vignesh Raghavendra for TI K3
- Build fixes to address randconfig warnings in sharpsl, dove, omap1,
and qcom platforms as well as the scmi and op-tee subsystems
- Regression fixes for missing CONFIG_FB and other options for
several defconfigs
- Several bug fixes for the newly added Microchip SAMA7 platform,
mostly regarding power management
- Missing SMP barriers to protect accesses to SCMI virtio device
- Regression fixes for TI OMAP, including a boot-time hang on am335x.
- Lots of bug fixes for NXP i.MX, mostly addressing incorrect
settings in devicetree files, and one revert for broken suspend.
- Fixes for ARM Juno/Vexpress devicetree files, addressing a couple
of schema warnings.
- Regression fixes for qualcomm SoC specific drivers and devicetree
files, reverting an mdt_loader change and at least pastially
reverting some of the 5.15 DTS changes, plus some minor bugfixes"
* tag 'armsoc-fixes-5.15' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (64 commits)
MAINTAINERS: Add Sven Peter as ARM/APPLE MACHINE maintainer
MAINTAINERS: Add Alyssa Rosenzweig as M1 reviewer
firmware: arm_scmi: Add proper barriers to scmi virtio device
firmware: arm_scmi: Simplify spinlocks in virtio transport
ARM: dts: omap3430-sdp: Fix NAND device node
bus: ti-sysc: Use CLKDM_NOAUTO for dra7 dcan1 for errata i893
ARM: sharpsl_param: work around -Wstringop-overread warning
ARM: defconfig: gemini: Restore framebuffer
ARM: dove: mark 'putc' as inline
ARM: omap1: move omap15xx local bus handling to usb.c
MAINTAINERS: Add Vignesh to TI K3 platform maintainership
arm64: dts: imx8m*-venice-gw7902: fix M2_RST# gpio
ARM: imx6: disable the GIC CPU interface before calling stby-poweroff sequence
arm64: dts: ls1028a: fix eSDHC2 node
arm64: dts: imx8mm-kontron-n801x-som: do not allow to switch off buck2
ARM: dts: at91: sama7g5ek: to not touch slew-rate for SDMMC pins
ARM: dts: at91: sama7g5ek: use proper slew-rate settings for GMACs
ARM: at91: pm: preload base address of controllers in tlb
ARM: at91: pm: group constants and addresses loading
ARM: dts: at91: sama7g5ek: add suspend voltage for ddr3l rail
...
