Needed for boards that wire the CEC pin in such a way that it
is unavailable when the HPD is low.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
If the mdp_* nodes are under an mdp sub-node, their corresponding
platform device does not automatically get its iommu assigned properly.
Fix this by moving the mdp component nodes up a level such that they are
siblings of mdp and all other SoC subsystems. This also simplifies the
device tree.
Although it fixes iommu assignment issue, it also break compatibility
with old device tree. So, the patch in driver is needed to iterate over
sibling mdp device nodes, not child ones, to keep driver work properly.
Signed-off-by: Minghsiu Tsai <minghsiu.tsai@mediatek.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The original bindings documentation was incomplete (missing pinctrl-names,
missing endpoint node properties) and the example was out of date.
Add the missing information and tidy up the text.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Acked-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
It turned out that all versions of MFC v6+ hardware doesn't have a strict
requirement for ALL buffers to be allocated on higher addresses than the
firmware base like it was documented for MFC v5. This requirement is true
only for the device and per-context buffers. All video data buffers can be
allocated anywhere for all MFC v6+ versions. Basing on this fact, the
special DMA configuration based on two reserved memory regions is not
really needed for MFC v6+ devices, because the memory requirements for the
firmware, device and per-context buffers can be fulfilled by the simple
probe-time pre-allocated block allocator introduced in previous patch.
This patch enables support for such pre-allocated block based allocator
always for MFC v6+ devices. Due to the limitations of the memory management
subsystem the largest supported size of the pre-allocated buffer when no
CMA (Contiguous Memory Allocator) is enabled is 4 MiB.
This patch also removes the requirement to provide two reserved memory
regions for MFC v6+ devices in device tree. Now the driver is fully
functional without them.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Reviewed-by: Javier Martinez Canillas <javier@osg.samsung.com>
Tested-by: Javier Martinez Canillas <javier@osg.samsung.com>
Acked-by: Andrzej Hajda <a.hajda@samsung.com>
Tested-by: Smitha T Murthy <smitha.t@samsung.com>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The driver already parses the "linux,rc-map-name" property. Add this
information to the documentation so .dts maintainers don't have to look
it up in the source-code.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Add a DT binding documentation for the Video Data Order Adapter (VDOA)
of the Freescale i.MX6 SoC.
Also, add the compatible property and correct clock to the device tree
to match the documentation.
Signed-off-by: Philipp Zabel <philipp.zabel@gmail.com>
Signed-off-by: Michael Tretter <m.tretter@pengutronix.de>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Most IR drivers uses the same label to identify the
scancode/key table they used by multiple bindings and lack
explanation well. So move the shared property into a common
place and give better explanation.
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Pull media updates from Mauro Carvalho Chehab:
- new Mediatek drivers: mtk-mdp and mtk-vcodec
- some additions at the media documentation
- the CEC core and drivers were promoted from staging to mainstream
- some cleanups at the DVB core
- the LIRC serial driver got promoted from staging to mainstream
- added a driver for Renesas R-Car FDP1 driver
- add DVBv5 statistics support to mn88473 driver
- several fixes related to printk continuation lines
- add support for HSV encoding formats
- lots of other cleanups, fixups and driver improvements.
* tag 'media/v4.10-1' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media: (496 commits)
[media] v4l: tvp5150: Add missing break in set control handler
[media] v4l: tvp5150: Don't inline the tvp5150_selmux() function
[media] v4l: tvp5150: Compile tvp5150_link_setup out if !CONFIG_MEDIA_CONTROLLER
[media] em28xx: don't store usb_device at struct em28xx
[media] em28xx: use usb_interface for dev_foo() calls
[media] em28xx: don't change the device's name
[media] mn88472: fix chip id check on probe
[media] mn88473: fix chip id check on probe
[media] lirc: fix error paths in lirc_cdev_add()
[media] s5p-mfc: Add support for MFC v8 available in Exynos 5433 SoCs
[media] s5p-mfc: Rework clock handling
[media] s5p-mfc: Don't keep clock prepared all the time
[media] s5p-mfc: Kill all IS_ERR_OR_NULL in clocks management code
[media] s5p-mfc: Remove dead conditional code
[media] s5p-mfc: Ensure that clock is disabled before turning power off
[media] s5p-mfc: Remove special clock rate management
[media] s5p-mfc: Use printk_ratelimited for reporting ioctl errors
[media] s5p-mfc: Set DMA_ATTR_ALLOC_SINGLE_PAGES
[media] vivid: Set color_enc on HSV formats
[media] v4l2-tpg: Init hv_enc field with a valid value
...
Exynos5433 SoC has MFC v8 hardware module, but it has more
complex clock hierarchy, so a new compatible is added.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
This patch adds support for Exynos5433 specific version of the GScaler
module. The main difference between Exynos 5433 and earlier is addition
of new clocks that have to be controlled.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Reviewed-by: Javier Martinez Canillas <javier@osg.samsung.com>
Tested-by: Javier Martinez Canillas <javier@osg.samsung.com>
Acked-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The text states that default-input is an endpoint property, but in the
example it is a device property.
The default input is a property of the chip, not of a particular port, so
the example makes more sense.
Signed-off-by: Ulrich Hecht <ulrich.hecht+renesas@gmail.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Pull media updates from Mauro Carvalho Chehab:
- Documentation improvements: conversion of all non-DocBook documents
to Sphinx and lots of fixes to the uAPI media book
- New PCI driver for Techwell TW5864 media grabber boards
- New SoC driver for ATMEL Image Sensor Controller
- Removal of some obsolete SoC drivers (s5p-tv driver and soc_camera
drivers)
- Addition of ST CEC driver
- Lots of drivers fixes, improvements and additions
* tag 'media/v4.9-1' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media: (464 commits)
[media] ttusb_dec: avoid the risk of go past buffer
[media] cx23885: Fix some smatch warnings
[media] si2165: switch to regmap
[media] si2165: use i2c_client->dev instead of i2c_adapter->dev for logging
[media] si2165: Remove legacy attach
[media] cx231xx: attach si2165 driver via i2c_client
[media] cx231xx: Prepare for attaching new style i2c_client DVB demod drivers
[media] cx23885: attach si2165 driver via i2c_client
[media] si2165: support i2c_client attach
[media] si2165: avoid division by zero
[media] rcar-vin: add R-Car gen2 fallback compatibility string
[media] lgdt3306a: remove 20*50 msec unnecessary timeout
[media] cx25821: Remove deprecated create_singlethread_workqueue
[media] cx25821: Drop Freeing of Workqueue
[media] cxd2841er: force 8MHz bandwidth for DVB-C if specified bw not supported
[media] redrat3: hardware-specific parameters
[media] redrat3: remove hw_timeout member
[media] cxd2841er: BER and SNR reading for ISDB-T
[media] dvb-usb: avoid link error with dib3000m{b,c|
[media] dvb-usb: split out common parts of dibusb
...
This patch adds 3 more clocks to Exynos4 ISP driver. Enabling them is
needed to make the hardware operational. Till now it worked only because
those clocks were registered with IGNORE_UNUSED flag and were enabled
by default after SoC reset.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Acked-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
