MDA_ADDR is one of those macros which could be an inline function. So
convert MDA_ADDR to mda_addr.
Note that we take x and y as unsigned now. But they are absolute
coordinates, so this is no problem.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Cc: Tomi Valkeinen <tomi.valkeinen@ti.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Given every user of mda_vram_base expects a pointer, let
mda_vram_base be a pointer to u16.
The offset calculation in mda_detect had to be adjusted by / 2 (due to
different pointer arithmetic now).
We introduce a cast to a value returned from VGA_MAP_MEM. But I will
change VGA_MAP_MEM to return a pointer later too. But vgacon needs a
similar change first.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Cc: Tomi Valkeinen <tomi.valkeinen@ti.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
This is just a whitespace cleanup. The code was a mess having multiple
commands on one line like:
scr_writew(0xAA55, p); if (scr_readw(p) == 0xAA55) count++;
Indent that properly and make it nicer for reading.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Cc: Tomi Valkeinen <tomi.valkeinen@ti.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
There are a bunch of error paths were we don't unlock the bpmp->threaded
lock. Also if __tegra_bpmp_channel_write() fails then we returned
success instead of an error code.
Fixes: 983de5f971 ("firmware: tegra: Add BPMP support")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Enables the ADV7180 decoder sensor. The ADV7180 connects to the
parallel-bus mux input on ipu1_csi0_mux.
The ADV7180 power pin is via max7310_b port expander.
Changes from Tim Harvey:
- Use IRQ_TYPE_LEVEL_LOW instead of 0x8 for interrupt type for clarity.
- For 8-bit parallel IPU1-CSI0 bus connection only data[12-19] are used.
Signed-off-by: Steve Longerbeam <steve_longerbeam@mentor.com>
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The reset pin to the port expander chip (MAX7310) is controlled by a gpio,
so define a reset-gpios property to control it. There are three MAX7310's
on the SabreAuto CPU card (max7310_[abc]), but all use the same pin for
their reset. Since all can't acquire the same pin, assign it to max7310_b,
that chip is needed by more functions (usb and adv7180).
Signed-off-by: Steve Longerbeam <steve_longerbeam@mentor.com>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The sabreauto uses a steering pin to select between the SDA signal on
i2c3 bus, and a data-in pin for an SPI NOR chip. Use i2cmux to control
this steering pin. Idle state of the i2cmux selects SPI NOR. This is not
a classic way to use i2cmux, since one side of the mux selects something
other than an i2c bus, but it works and is probably the cleanest
solution. Note that if one thread is attempting to access SPI NOR while
another thread is accessing i2c3, the SPI NOR access will fail since the
i2cmux has selected the SDA pin rather than SPI NOR data-in. This couldn't
be avoided in any case, the board is not designed to allow concurrent
i2c3 and SPI NOR functions (and the default device-tree does not enable
SPI NOR anyway).
Devices hanging off i2c3 should now be defined under i2cmux, so
that the steering pin can be properly controlled to access those
devices. The port expanders (MAX7310) are thus moved into i2cmux.
Signed-off-by: Steve Longerbeam <steve_longerbeam@mentor.com>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Enables the OV5642 parallel-bus sensor, and the OV5640 MIPI CSI-2 sensor.
The OV5642 connects to the parallel-bus mux input port on ipu1_csi0_mux.
The OV5640 connects to the input port on the MIPI CSI-2 receiver on
mipi_csi.
Until the OV5652 sensor module compatible with the SabreSD becomes
available for testing, the ov5642 node is currently disabled.
Signed-off-by: Steve Longerbeam <steve_longerbeam@mentor.com>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Adds the OV5642 parallel-bus sensor, and the OV5640 MIPI CSI-2 sensor.
Both hang off the same i2c2 bus, so they require different (and non-
default) i2c slave addresses.
The OV5642 connects to the parallel-bus mux input port on ipu1_csi0_mux.
The OV5640 connects to the input port on the MIPI CSI-2 receiver on
mipi_csi.
The OV5642 node is disabled temporarily while the subdev driver is
cleaned up and submitted later.
Signed-off-by: Steve Longerbeam <steve_longerbeam@mentor.com>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
There is a pin conflict with GPIO_6. This pin functions as a power
input pin to the OV5642 camera sensor, but ENET uses it as the h/w
workaround for erratum ERR006687, to wake-up the ARM cores on normal
RX and TX packet done events. So we need to remove the h/w workaround
to support the OV5642. The result is that the CPUidle driver will no
longer allow entering the deep idle states on the sabrelite.
This is a partial revert of
commit 6261c4c8f1 ("ARM: dts: imx6qdl-sabrelite: use GPIO_6 for FEC
interrupt.")
commit a28eeb43ee ("ARM: dts: imx6: tag boards that have the HW workaround
for ERR006687")
Signed-off-by: Steve Longerbeam <steve_longerbeam@mentor.com>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
This patch adds the device tree graph connecting the input multiplexers
to the IPU CSIs and the MIPI-CSI2 gasket on i.MX6. The MIPI_IPU
multiplexers are added as children of the iomuxc-gpr syscon device node.
On i.MX6Q/D two two-input multiplexers in front of IPU1 CSI0 and IPU2
CSI1 allow to select between CSI0/1 parallel input pads and the MIPI
CSI-2 virtual channels 0/3.
On i.MX6DL/S two five-input multiplexers in front of IPU1 CSI0 and IPU1
CSI1 allow to select between CSI0/1 parallel input pads and any of the
four MIPI CSI-2 virtual channels.
Changes from Steve Longerbeam:
- Removed some dangling/unused endpoints (ipu2_csi0_from_csi2ipu)
- Renamed the mipi virtual channel endpoint labels, from "mipi_csiX_..."
to "mipi_vcX...".
- Added input endpoint anchors to the video muxes for the connections
from parallel sensors.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Steve Longerbeam <steve_longerbeam@mentor.com>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The IOMUXC General Purpose Register space contains various bitfields
that control video bus multiplexers. Describe them using a mmio-mux
node. The placement of the IPU CSI video mux controls differs between
i.MX6D/Q and i.MX6S/DL.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
his used to be a fall through case, but we shifted code around and I
think we want a break here now.
Fixes: 4e4cbee93d ("block: switch bios to blk_status_t")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
The standard PCM chmap helper callbacks treat the NULL info->chmap as
a fatal error and spews the kernel warning with stack trace when
CONFIG_SND_DEBUG is on. This was OK, originally it was supposed to be
always static and non-NULL. But, as the recent addition of Intel LPE
audio driver shows, the chmap content may vary dynamically, and it can
be even NULL when disconnected. The user still sees the kernel
warning unnecessarily.
For clearing such a confusion, this patch simply removes the
snd_BUG_ON() in each place, just returns an error without warning.
Cc: <stable@vger.kernel.org> # v4.11+
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This reverts the two commits
7afbeb6df2 ("s390/ipl: always use load normal for CCW-type re-IPL")
0f7451ff3a ("s390/ipl: use load normal for LPAR re-ipl")
The two commits did not take into account that behavior of standby
memory changes fundamentally if the re-IPL method is changed from
Load Clear to Load Normal.
In case of the old re-IPL clear method all memory that was initially
in standby state will be put into standby state again within the
re-IPL process. Or in other words: memory that was brought online
before a re-IPL will be offline again after a reboot.
Given that we use different re-IPL methods depending on the hypervisor
and CCW-type vs SCSI re-IPL it is not easy to tell in advance when and
why memory will stay online or will be offline after a re-IPL.
This does also have other side effects, since memory that is online
from the beginning will be in ZONE_NORMAL by default vs ZONE_MOVABLE
for memory that is offline.
Therefore, before the change, a user could online and offline memory
easily since standby memory was always in ZONE_NORMAL. After the
change, and a re-IPL, this depended on which memory parts were online
before the re-IPL.
From a usability point of view the current behavior is more than
suboptimal. Therefore revert these changes until we have a better
solution and get back to a consistent behavior. The bad thing about
this is that the time required for a re-IPL will be significantly
increased for configurations with several 100GB or 1TB of memory.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
The current implementation of F_SETOWN doesn't properly vet the argument
passed in and only returns an error if INT_MIN is passed in. If the
argument doesn't specify a valid pid/pgid, then we just end up cleaning
out the file->f_owner structure.
What we really want is to only clean that out only in the case where
userland passed in an argument of 0. For anything else, we want to
return ESRCH if it doesn't refer to a valid pid.
The relevant POSIX spec page is here:
http://pubs.opengroup.org/onlinepubs/9699919799/functions/fcntl.html
Cc: Jiri Slaby <jslaby@suse.cz>
Cc: zhong jiang <zhongjiang@huawei.com>
Signed-off-by: Jeff Layton <jlayton@redhat.com>
fcntl(0, F_SETOWN, 0x80000000) triggers:
UBSAN: Undefined behaviour in fs/fcntl.c:118:7
negation of -2147483648 cannot be represented in type 'int':
CPU: 1 PID: 18261 Comm: syz-executor Not tainted 4.8.1-0-syzkaller #1
...
Call Trace:
...
[<ffffffffad8f0868>] ? f_setown+0x1d8/0x200
[<ffffffffad8f19a9>] ? SyS_fcntl+0x999/0xf30
[<ffffffffaed1fb00>] ? entry_SYSCALL_64_fastpath+0x23/0xc1
Fix that by checking the arg parameter properly (against INT_MAX) before
"who = -who". And return immediatelly with -EINVAL in case it is wrong.
Note that according to POSIX we can return EINVAL:
http://pubs.opengroup.org/onlinepubs/9699919799/functions/fcntl.html
[EINVAL]
The cmd argument is F_SETOWN and the value of the argument
is not valid as a process or process group identifier.
[v2] returns an error, v1 used to fail silently
[v3] implement proper check for the bad value INT_MIN
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Cc: Jeff Layton <jlayton@poochiereds.net>
Cc: "J. Bruce Fields" <bfields@fieldses.org>
Cc: Alexander Viro <viro@zeniv.linux.org.uk>
Cc: linux-fsdevel@vger.kernel.org
Signed-off-by: Jeff Layton <jlayton@redhat.com>
This implements a driver that exposes the IPC bits found in the APCS
Global block in various Qualcomm platforms. The bits are used to signal
inter-processor communication signals from the application CPU to other
masters.
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Jassi Brar <jaswinder.singh@linaro.org>
Introduce a binding for the Qualcomm APCS global block, exposing a
mailbox for invoking interrupts on remote processors in the system.
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Jassi Brar <jaswinder.singh@linaro.org>
Some mailbox hardware doesn't have to perform any additional operations
on startup of shutdown, so make these optional.
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Jassi Brar <jaswinder.singh@linaro.org>
Unfortunately, struct iwreq isn't a proper subset of struct ifreq,
but is still handled by the same code path. Robert reported that
then applications may (randomly) fault if the struct iwreq they
pass happens to land within 8 bytes of the end of a mapping (the
struct is only 32 bytes, vs. struct ifreq's 40 bytes).
To fix this, pull out the code handling wireless extension ioctls
and copy only the smaller structure in this case.
This bug goes back a long time, I tracked that it was introduced
into mainline in 2.1.15, over 20 years ago!
This fixes https://bugzilla.kernel.org/show_bug.cgi?id=195869
Reported-by: Robert O'Callahan <robert@ocallahan.org>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
To make it clear that we never use struct ifreq, cast from it
directly in the wext entrypoint and use struct iwreq from there
on. The next patch will remove the cast again and pass the
correct struct from the beginning.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
SNDRV_PCM_IOCTL1_GSTATE was firstly introduced in v0.9.0, however never
be used and the purpose is missing.
This commit removes the long-abandoned command, bye.
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Drivers can implement 'struct snd_pcm_ops.ioctl' to handle some requests
from ALSA PCM core. These requests are internal purpose in kernel land.
Usually common set of operations are used for it.
SNDRV_PCM_IOCTL1_INFO is one of the requests. According to code comment,
it has been obsoleted in the old days.
We can see old releases in ftp.alsa-project.org. The command was firstly
introduced in v0.5.0 release as SND_PCM_IOCTL1_INFO, to allow drivers to
fill data of 'struct snd_pcm_channel_info' type. In v0.9.0 release,
this was obsoleted by the other commands for ioctl(2) such as
SNDRV_PCM_IOCTL_CHANNEL_INFO.
This commit removes the long-abandoned command, bye.
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Now that AVR32 is gone, platform_data are not used to initialize the driver
anymore, remove that path from the driver. Also remove the now unused
struct atmel_uart_data.
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Acked-by: Richard Genoud <richard.genoud@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The caller only cares about zero vs non-zero so this code actually works
fine but we should be returning a negative error code instead of a valid
pointer casted to int.
Fixes: 554c0a3abf ("staging: Add rtl8723bs sdio wifi driver")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The default error code in pfkey_msg2xfrm_state() is -ENOBUFS. We
added a new call to security_xfrm_state_alloc() which sets "err" to zero
so there several places where we can return ERR_PTR(0) if kmalloc()
fails. The caller is expecting error pointers so it leads to a NULL
dereference.
Fixes: df71837d50 ("[LSM-IPSec]: Security association restriction.")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
There are some missing error codes here so we accidentally return NULL
instead of an error pointer. It results in a NULL pointer dereference.
Fixes: df71837d50 ("[LSM-IPSec]: Security association restriction.")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
Drop log level for blanking from info to debug. Xorg likes to habitually
unblank when already unblanked and this can fill up logs over a long period
of time.
Signed-off-by: Mike Gerow <gerow@google.com>
Cc: bernie@plugable.com
Signed-off-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
When CONFIG_PROC_FS is disabled, we get warnings about unused variables
as remove_proc_entry() evaluates to an empty macro.
drivers/video/fbdev/via/viafbdev.c: In function 'viafb_remove_proc':
drivers/video/fbdev/via/viafbdev.c:1635:4: error: unused variable 'iga2_entry' [-Werror=unused-variable]
drivers/video/fbdev/via/viafbdev.c:1634:4: error: unused variable 'iga1_entry' [-Werror=unused-variable]
These are easy to avoid by using the pointer from the structure.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Cc: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
Signed-off-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
gcc-7 suspects this code might be wrong because we use the
result of a multiplication as a bool:
drivers/video/fbdev/core/fbmon.c: In function 'fb_edid_add_monspecs':
drivers/video/fbdev/core/fbmon.c:1051:84: error: '*' in boolean context, suggest '&&' instead [-Werror=int-in-bool-context]
It's actually fine, so let's add a comparison to zero to make
that clear to the compiler too.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Cc: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Use variable name instead of structure name to get size
of memory to allocate as proposed by checkpatch.pl
Signed-off-by: Aliaksei Karaliou <akaraliou.dev@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
