Use the recently introduced helper to replace the pattern of
skb_put() && memset(), this transformation was done with the
following spatch:
@@
identifier p;
expression len;
expression skb;
@@
-p = skb_put(skb, len);
-memset(p, 0, len);
+p = skb_put_zero(skb, len);
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Johannes Berg says:
====================
A couple of weeks worth of updates - looks like things are quiet:
* merged net-next back to get a patch from net that another patch
here depends on
* various small improvements/cleanups across the board
* 4-way handshake offload (many thanks to Arend for shepherding that)
* mesh CSA/DFS support in mac80211
* the skb_put_zero() we discussed previously
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Now struct spi_master is used for both SPI master and slave controllers,
it makes sense to rename it to struct spi_controller, and replace
"master" by "controller" where appropriate.
For now this conversion is done for SPI core infrastructure only.
Wrappers are provided for backwards compatibility, until all SPI drivers
have been converted.
Noteworthy details:
- SPI_MASTER_GPIO_SS is retained, as it only makes sense for SPI
master controllers,
- spi_busnum_to_master() is retained, as it looks up masters only,
- A new field spi_device.controller is added, but spi_device.master is
retained for compatibility (both are always initialized by
spi_alloc_device()),
- spi_flash_read() is used by SPI masters only.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Mark Brown <broonie@kernel.org>
Simon Wunderlich says:
====================
This feature/cleanup patchset includes the following patches:
- bump version strings, by Simon Wunderlich
- decrease maximum fragment size, by Matthias Schiffer
- Clean up seqfile writing, by Markus Elfring (2 patches)
- use __func__ in debug messages, by Sven Eckelmann
- Mark tpmeter initializers with __init, by Antonio Quartulli
- ignore loop detection MAC addresses, by Simon Wunderlich
- clean up some return handling, by Simon Wunderlich
- improve ELP throughput value handling for WiFi neighbors
in BATMAN V/ELP, by Sven Eckelmann (2 patches)
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Check TPS65910_NUM_REGS at build time instead of silently registering
not all regulators at runtime.
Signed-off-by: Michał Mirosław <mirq-linux@rere.qmqm.pl>
Signed-off-by: Mark Brown <broonie@kernel.org>
Simon Wunderlich says:
====================
Here are two batman-adv bugfixes:
- fix rx packet counters for local ARP replies, by Sven Eckelmann
- fix memory leaks for unicast packetes received from another gateway
in bridge loop avoidance, by Andreas Pape
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, when looking up a regulator supply, the regulator name
takes priority over the consumer mappings. As there are a lot of
regulator names that are in fairly common use (VDD, MICVDD, etc.) this
can easily lead to obtaining the wrong supply, when a system contains
two regulators that share a name.
The explicit consumer mappings contain much less ambiguity as they
specify both a name and a consumer device. As such prioritise those if
one exists and only fall back to the regulator name if there are no
matching explicit mappings.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Johannes Berg says:
====================
Some fixes:
* Avi fixes some fallout from my mac80211 RX flags changes
* Emmanuel fixes an issue with adhering to the spec, and
an oversight in the SMPS management code
* Jason's patch makes mac80211 use constant-time memory
comparisons for message authentication, to avoid having
potentially observable timing differences
* my fix makes mac80211 set the basic rates bitmap before
the channel so the next update to the driver has more
consistent data - this required another rework patch to
remove some useless 5/10 MHz code that can never be hit
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently when dumping a context data only word number '1' is read for the
entire context.
Fixes: c965db4446 ("qed: Add support for debug data collection")
Signed-off-by: Tomer Tayar <Tomer.Tayar@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix the position of arguments so camif->colorfx_cb, camif->colorfx_cr
are passed in proper order to the camif_hw_set_effect() function.
Addresses-Coverity-ID: 1248800
Addresses-Coverity-ID: 1269141
[s.nawrocki@samsung.com: edited commit message ]
Signed-off-by: Gustavo A. R. Silva <garsilva@embeddedor.com>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
As this is not in atomic context and it does not seem like a critical
timing setting a range of 1ms allows the timer subsystem to optimize
the hrtimer here.
Signed-off-by: Nicholas Mc Guire <hofrat@osadl.org>
Acked-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
A new Sierra Wireless EM7305 device ID used in a Toshiba laptop,
and two Longcheer device IDs entries used by Telewell TW-3G HSPA+
branded modems.
Reported-by: Petr Kloc <petr_kloc@yahoo.com>
Reported-by: Teemu Likonen <tlikonen@iki.fi>
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use colorspace provided by the user as we are only doing scaling and
color encoding conversion, we won't be able to transform the colorspace
itself and the colorspace won't mater in that operation.
Also always use output colorspace on the capture side.
If the user does not provide a colorspace do not make it up, we might
later while processing need to figure out the colorspace, which
is possible depending on the frame size but do not ever guess and
leak that guess to the userspace.
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Thibault Saunier <thibault.saunier@osg.samsung.com>
Reviewed-by: Andrzej Hajda <a.hajda@samsung.com>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The function flush_signals clears all pending signals for the process. It
may be used by kernel threads when we need to prepare a kernel thread for
responding to signals. However using this function for an userspaces
processes is incorrect - clearing signals without the program expecting it
can cause misbehavior.
The raid1 and raid5 code uses flush_signals in its request routine because
it wants to prepare for an interruptible wait. This patch drops
flush_signals and uses sigprocmask instead to block all signals (including
SIGKILL) around the schedule() call. The signals are not lost, but the
schedule() call won't respond to them.
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Cc: stable@vger.kernel.org
Acked-by: NeilBrown <neilb@suse.com>
Signed-off-by: Shaohua Li <shli@fb.com>
If mddev_suspend() races with md_write_start() we can deadlock
with mddev_suspend() waiting for the request that is currently
in md_write_start() to complete the ->make_request() call,
and md_write_start() waiting for the metadata to be updated
to mark the array as 'dirty'.
As metadata updates done by md_check_recovery() only happen then
the mddev_lock() can be claimed, and as mddev_suspend() is often
called with the lock held, these threads wait indefinitely for each
other.
We fix this by having md_write_start() abort if mddev_suspend()
is happening, and ->make_request() aborts if md_write_start()
aborted.
md_make_request() can detect this abort, decrease the ->active_io
count, and wait for mddev_suspend().
Reported-by: Nix <nix@esperi.org.uk>
Fix: 68866e425be2(MD: no sync IO while suspended)
Cc: stable@vger.kernel.org
Signed-off-by: NeilBrown <neilb@suse.com>
Signed-off-by: Shaohua Li <shli@fb.com>
After commit 90eff9096c ("net: phy: Allow splitting MDIO
bus/device support from PHYs") we could create a configuration where
MDIO_DEVICE=y and PHYLIB=m which leads to the following undefined
references:
drivers/built-in.o: In function `thunder_mdiobus_pci_remove':
>> mdio-thunder.c:(.text+0x2a212f): undefined reference to
>> `mdiobus_unregister'
>> mdio-thunder.c:(.text+0x2a2138): undefined reference to
>> `mdiobus_free'
drivers/built-in.o: In function `thunder_mdiobus_pci_probe':
mdio-thunder.c:(.text+0x2a22e7): undefined reference to
`devm_mdiobus_alloc_size'
mdio-thunder.c:(.text+0x2a236f): undefined reference to
`of_mdiobus_register'
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Fixes: 90eff9096c ("net: phy: Allow splitting MDIO bus/device support from PHYs")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Tested-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
It's already added by pr_fmt so remove the explicit use.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
v4l2_m2m_job_finish(), which is called from the interrupt handler with
slock acquired, can call the device_run() hook immediately if another
context was in the queue. This hook also acquires slock, resulting in
a deadlock for this scenario.
Fix this by releasing slock right before calling v4l2_m2m_job_finish().
This is safe to do as the state of the hardware cannot change before
v4l2_m2m_job_finish() is called anyway.
Signed-off-by: Alexandre Courbot <acourbot@chromium.org>
Acked-by: Jacek Anaszewski <jacek.anaszewski@gmail.com>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Sergei Shtylyov says:
====================
MDIO bus reset GPIO cleanups
Commit 4c5e7a2c05 ("dt-bindings: mdio: Clarify binding document")
declared that a MDIO reset GPIO property should have only a single GPIO
reference/specifier, however the supporting code was left intact...
Here's a couple of the obvious cleanups to that code:
[1/2] mdio_bus: handle only single PHY reset GPIO
[2/2] mdio_bus: use devm_gpiod_get_optional()
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
The MDIO reset GPIO is really a classical optional GPIO property case,
so devm_gpiod_get_optional() should have been used, not devm_gpiod_get().
Doing this saves several LoCs...
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 4c5e7a2c05 ("dt-bindings: mdio: Clarify binding document")
declared that a MDIO reset GPIO property should have only a single GPIO
reference/specifier, however the supporting code was left intact, still
burdening the kernel with now apparently useless loops -- get rid of them.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Now that rc_register_device() is reorganised, the dev->initialized
hack can be removed. Any driver which calls rc_register_device()
must be prepared for the device to go live immediately.
The dev->initialized commits that are relevant are commit c73bbaa4ec
("[media] rc-core: don't lock device at rc_register_device()") and
commit 08aeb7c9a4 ("[media] rc: add locking to fix register/show race").
The original problem was that show_protocols() would access
dev->rc_map.* and various other bits which are now properly
initialized before device_add() is called.
At the same time, remove the bogus "device is being removed" check.
Signed-off-by: David Härdeman <david@hardeman.nu>
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The device core infrastructure is based on the presumption that
once a driver calls device_add(), it must be ready to accept
userspace interaction.
This requires splitting rc_setup_rx_device() into two functions
and reorganizing rc_register_device() so that as much work
as possible is performed before calling device_add().
Signed-off-by: David Härdeman <david@hardeman.nu>
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
When handling a driver reset due to a failover of the backing
server on the vios, doing the netdev_notify_peers() can cause
network traffic to stall or halt. Remove the netdev notify call
for failover resets.
Signed-off-by: Nathan Fontenot <nfont@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The IBM vNIC protocol provides support for the user to initiate
a failover from the client LPAR in case the current backing infrastructure
is deemed inadequate or in an error state.
Support for two H_VIOCTL sub-commands for vNIC devices are required
to implement this function. These commands are H_GET_SESSION_TOKEN
and H_SESSION_ERR_DETECTED.
"[H_GET_SESSION_TOKEN] is used to obtain a session token from a VNIC client
adapter. This token is opaque to the caller and is intended to be used in
tandem with the SESSION_ERROR_DETECTED vioctl subfunction."
"[H_SESSION_ERR_DETECTED] is used to report that the currently active
backing device for a VNIC client adapter is behaving poorly, and that
the hypervisor should attempt to fail over to a different backing device,
if one is available."
To provide tools access to this functionality the vNIC driver creates a
sysfs file that, when written to, will send a request to pHyp to failover
to a different backing device.
Signed-off-by: Thomas Falcon <tlfalcon@linux.vnet.ibm.com>
Reviewed-by: Nathan Fontenot <nfont@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Andrey reported a use-after-free in add_grec():
for (psf = *psf_list; psf; psf = psf_next) {
...
psf_next = psf->sf_next;
where the struct ip_sf_list's were already freed by:
kfree+0xe8/0x2b0 mm/slub.c:3882
ip_mc_clear_src+0x69/0x1c0 net/ipv4/igmp.c:2078
ip_mc_dec_group+0x19a/0x470 net/ipv4/igmp.c:1618
ip_mc_drop_socket+0x145/0x230 net/ipv4/igmp.c:2609
inet_release+0x4e/0x1c0 net/ipv4/af_inet.c:411
sock_release+0x8d/0x1e0 net/socket.c:597
sock_close+0x16/0x20 net/socket.c:1072
This happens because we don't hold pmc->lock in ip_mc_clear_src()
and a parallel mr_ifc_timer timer could jump in and access them.
The RCU lock is there but it is merely for pmc itself, this
spinlock could actually ensure we don't access them in parallel.
Thanks to Eric and Long for discussion on this bug.
Reported-by: Andrey Konovalov <andreyknvl@google.com>
Cc: Eric Dumazet <edumazet@google.com>
Cc: Xin Long <lucien.xin@gmail.com>
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Reviewed-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
On GOP port 0 two MAC modes are available: GMAC and XLG. The XLG MAC is
used for 10G connectivity. This patch adds a basic 10G support by
allowing to use the XLG MAC on port 0 and by reworking the
port_enable/disable functions so that the XLG MAC is configured when
using 10G.
Signed-off-by: Antoine Tenart <antoine.tenart@free-electrons.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Getting the device version out of the driver really aids debugging.
Signed-off-by: Oliver Neukum <oneukum@suse.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This module was merged after commit 5a8fc6a3ce ("Annotate hardware
config module parameters in drivers/media/"), so add add the missing
hardware annotations.
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
This patch add cec driver for STM32 platforms.
cec hardware block isn't not always used with hdmi so
cec notifier is not implemented. That will be done later
when STM32 DSI driver will be available.
Driver compliance has been tested with cec-ctl and cec-compliance
tools.
Signed-off-by: Benjamin Gaignard <benjamin.gaignard@linaro.org>
Signed-off-by: Yannick Fertre <yannick.fertre@st.com>
[hans.verkuil@cisco.com: modified platform/Makefile to use obj-y]
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The function find_smbios_instance_string() does not consider the
PCI domain number. As a result, SMBIOS type 41 device type instance
would be exported to sysfs for all the PCI domains which have a
PCI device with same bus/device/function, though PCI bus/device/func
from a specific PCI domain has SMBIOS type 41 device type instance
defined.
Address the issue by making find_smbios_instance_string() check PCI domain
number as well.
Reported-by: Shai Fultheim <Shai@ScaleMP.com>
Suggested-by: Shai Fultheim <Shai@ScaleMP.com>
Tested-by: Shai Fultheim <Shai@ScaleMP.com>
Signed-off-by: Sujith Pandel <sujithpshankar@gmail.com>
Signed-off-by: Narendra K <Narendra_K@Dell.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Remove the space from "PCI :" to make the message consistent with other PCI
messages.
Signed-off-by: Vincent Legoll <vincent.legoll@gmail.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
PCI_STD_RESOURCE_END is (confusingly) the index of the last valid BAR, not
the *number* of BARs. To iterate through all possible BARs, we need to
include PCI_STD_RESOURCE_END.
Fixes: 9fe373f999 ("PCI: Increase IBM ipr SAS Crocodile BARs to at least system page size")
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
PCI_STD_RESOURCE_END is (confusingly) the index of the last valid BAR, not
the *number* of BARs. To iterate through all possible BARs, we need to
include PCI_STD_RESOURCE_END.
Fixes: 55d728a40d ("efi/fb: Avoid reconfiguration of BAR that covers the framebuffer")
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
The APQ8060 Dragonboard has an Atmel AT24c128 EEPROM and a
Wolfson Micro WM8903 codec connected to its GSBI8 I2C bus.
Add entries for these to the device tree. The interrupt line
from the WM8903 chip is not routed anywhere on this design
so it can not be used.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
This patch fixes uninitialized symbol warning that
got introduced by the following commit
773fc8f6e8 ("net: rps: send out pending IPI's on CPU hotplug")
Signed-off-by: Ashwanth Goli <ashwanth@codeaurora.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Vivien Didelot says:
====================
net: dsa: mv88e6xxx: port macros cosmetics
This patch series brings no functional changes.
It prefixes all common port registers macros with MV88E6XXX_PORT.
If registers or some bits differs between switch models, a reference
model is chosen (e.g. MV88E6390_PORT_MAC_CTL_SPEED_10000.)
The register names are documented as found in the datasheets.
Avoid BIT() and shifts defines and prefer a better representation of the
Marvell switch registers with ordered, hexadecimal, 16-bit values.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
For implicit namespacing and clarity, prefix the remaining common Port
Registers macros with MV88E6XXX_PORT.
Document the register and prefer ordered hex masks values for all
Marvell 16-bit registers.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
For implicit namespacing and clarity, prefix the common Port IEEE
Priority Remapping registers macros with MV88E6095_PORT_IEEE_PRIO.
The 88E6390 family turned the 0x18 register into a single indirect
table, document that at the same time.
Document the register and prefer ordered hex masks values for all
Marvell 16-bit registers.
Also fix the following checkpatch checks with a temporary variable:
CHECK: Alignment should match open parenthesis
#65: FILE: drivers/net/dsa/mv88e6xxx/port.c:932:
+ err = mv88e6xxx_port_ieeepmt_write(chip, port,
+ MV88E6390_PORT_IEEE_PRIO_MAP_TABLE_INGRESS_PCP,
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
For implicit namespacing and clarity, prefix the common Port Association
Vector Register macros with MV88E6XXX_PORT_ASSOC_VECTOR.
Document the register and prefer ordered hex masks values for all
Marvell 16-bit registers.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
For implicit namespacing and clarity, prefix the common Port Egress Rate
Control and Port Egress Rate Control 2 registers macros with
MV88E6XXX_PORT_EGRESS_RATE_CTL1 and MV88E6XXX_PORT_EGRESS_RATE_CTL2.
Document the register and prefer ordered hex masks values for all
Marvell 16-bit registers.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
