On emulation systems, the EMAC's internal PHY ("SGMII") is not present,
but is not needed for network functionality. So just display a warning
message and ignore the SGMII.
Tested-by: Philip Elcan <pelcan@codeaurora.org>
Tested-by: Adam Wallis <awallis@codeaurora.org>
Signed-off-by: Timur Tabi <timur@codeaurora.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
On ACPI systems, the driver depends on firmware pre-initializing the
EMAC because we don't have access to the clocks, and the EMAC has specific
clock programming requirements. Therefore, we don't want to reset the
EMAC while we are completing the initialization.
Tested-by: Richard Ruigrok <rruigrok@codeaurora.org>
Signed-off-by: Timur Tabi <timur@codeaurora.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The shutdown function halts all DMA and interrupts, so that all
operations are discontinued when the system shuts down, e.g. via
kexec or a forced reboot.
Tested-by: Tyler Baicar <tbaicar@codeaurora.org>
Signed-off-by: Timur Tabi <timur@codeaurora.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Verify that the caller-provided sockaddr structure is large enough to
contain the sa_family field, before accessing it in bind() and connect()
handlers of the AF_IUCV socket. Since neither syscall enforces a minimum
size of the corresponding memory region, very short sockaddrs (zero or
one byte long) result in operating on uninitialized memory while
referencing .sa_family.
Fixes: 52a82e23b9 ("af_iucv: Validate socket address length in iucv_sock_bind()")
Signed-off-by: Mateusz Jurczyk <mjurczyk@google.com>
[jwi: removed unneeded null-check for addr]
Signed-off-by: Julian Wiedmann <jwi@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use proper endianness conversion for an skb protocol assignment. Given
that IUCV is only available on big endian systems (s390), this simply
avoids an endianness warning reported by sparse.
Signed-off-by: Hans Wippel <hwippel@linux.vnet.ibm.com>
Reviewed-by: Julian Wiedmann <jwi@linux.vnet.ibm.com>
Reviewed-by: Ursula Braun <ubraun@linux.vnet.ibm.com>
Signed-off-by: Julian Wiedmann <jwi@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We're accidentally returning the wrong variable. "cmode" is
uninitialized at this point so it causes a static checker warning.
Fixes: 6335e9f244 ("net: dsa: mv88e6xxx: mv88e6390X SERDES support")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Simon Horman says:
====================
nfp: add flower app with representors
this series adds a flower app to the NFP driver.
It initialises four types of netdevs:
* PF netdev - lower-device for communication of packets to device
* PF representor netdev
* VF representor netdevs
* Phys port representor netdevs
The PF netdev acts as a lower-device which sends and receives packets to
and from the firmware. The representors act as upper-devices. For TX
representors attach a metadata dst to the skb which is used by the PF
netdev to prepend metadata to the packet before forwarding the firmware. On
RX the PF netdev looks up the representor based on the prepended metadata
received from the firmware and forwards the skb to the representor after
removing the metadata.
Control queues are used to send and receive control messages which are
used to communicate configuration information with the firmware. These
are in separate vNIC to the queues belonging to the PF netdev. The control
queues are not exposed to use-space via a netdev or any other means.
The first 9 patches of this series provide app-independent infrastructure
to instantiate representors and the remaining 3 patches provide an app
which uses this infrastructure.
As the name implies this app is targeted at providing offload of TC flower.
Flower offload - allowing classifiers to be attached to representor netdevs
- is intended to be provided by follow-up patches at which point it will
become the dominant feature of the app.
Minor changes since v2 noted in changelogs of individual patches.
Review of v1 and v2 of this patchset have been addressed either
through discussion on-list or changes in this patchset.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Initialise VF and PF representors in flower app.
Based in part on work by Benjamin LaHaise, Bert van Leeuwen and
Jakub Kicinski.
Signed-off-by: Simon Horman <simon.horman@netronome.com>
Reviewed-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add app for flower offload. At this point the PF netdev and phys port
representor netdevs are initialised. Follow-up work will add support for
VF and PF representors and beyond that offloading the flower classifier.
Based in part on work by Benjamin LaHaise and Bert van Leeuwen.
Signed-off-by: Simon Horman <simon.horman@netronome.com>
Reviewed-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In preparation for adding a new flower app - targeted at offloading
the flower classifier - provide support for control message that it will
use to communicate with the NFP.
Based in part on work by Bert van Leeuwen.
Signed-off-by: Simon Horman <simon.horman@netronome.com>
Reviewed-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Allow tx/rx with metadata port id. This will be used for tx/rx of
representor netdevs acting as upper-devices while a pf netdev acts
as a lower-device.
Signed-off-by: Simon Horman <simon.horman@netronome.com>
Reviewed-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Provide port rather than vNIC as parameter of nfp_net_get_mac_addr.
This is to allow this function to be used by representor netdevs where
a vNIC may have more than one physical port none of which are associated
with the vNIC.
Signed-off-by: Simon Horman <simon.horman@netronome.com>
Reviewed-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add app-callbacks for app-specific initialisation of SRIOV.
Disabling SRIOV is brought forward in nfp_pci_remove()
so that nfp_app_sriov_disable is called while the app still exists.
This is intended to be used to implement representor netdevs for virtual
ports.
Signed-off-by: Simon Horman <simon.horman@netronome.com>
Reviewed-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Provide helpers for stats and xmit on representor netdevs.
Parts based on work by Bert van Leeuwen, Benjamin LaHaise and
Jakub Kicinski.
Signed-off-by: Simon Horman <simon.horman@netronome.com>
Reviewed-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Provide infrastructure to create and destroy representors of a given type.
Parts based on work by Bert van Leeuwen, Benjamin LaHaise,
and Jakub Kicinski.
Signed-off-by: Simon Horman <simon.horman@netronome.com>
Reviewed-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If present map mac_stats and vf_cfg BARs. These will be used by
representor netdevs to read statistics for phys port and vf representors.
Also provide defines describing the layout of the mac_stats area.
Similar defines are already present for the cf_cfg area.
Based in part on work by Jakub Kicinski.
Signed-off-by: Simon Horman <simon.horman@netronome.com>
Reviewed-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add app callback for reporting eswitch mode. Non-SRIOV apps
should not implement this callback, nfp_app code will then
respond with -EOPNOTSUPP.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: Simon Horman <simon.horman@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Switches and modern SR-IOV enabled NICs may multiplex traffic from Port
representators and control messages over single set of hardware queues.
Control messages and muxed traffic may need ordered delivery.
Those requirements make it hard to comfortably use TC infrastructure today
unless we have a way of attaching metadata to skbs at the upper device.
Because single set of queues is used for many netdevs stopping TC/sched
queues of all of them reliably is impossible and lower device has to
retreat to returning NETDEV_TX_BUSY and usually has to take extra locks on
the fastpath.
This patch attempts to enable port/representative devs to attach metadata
to skbs which carry port id. This way representatives can be queueless and
all queuing can be performed at the lower netdev in the usual way.
Traffic arriving on the port/representative interfaces will be have
metadata attached and will subsequently be queued to the lower device for
transmission. The lower device should recognize the metadata and translate
it to HW specific format which is most likely either a special header
inserted before the network headers or descriptor/metadata fields.
Metadata is associated with the lower device by storing the netdev pointer
along with port id so that if TC decides to redirect or mirror the new
netdev will not try to interpret it.
This is mostly for SR-IOV devices since switches don't have lower netdevs
today.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: Sridhar Samudrala <sridhar.samudrala@intel.com>
Signed-off-by: Simon Horman <horms@verge.net.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
When mc configuration changes bnx2x_config_mcast() can return 0 for
success, negative for failure and positive for benign reason preventing
its immediate work, e.g., when the command awaits the completion of
a previously sent command.
When removing all configured macs on a 578xx adapter, if a positive
value would be returned driver would errneously log it as an error.
Fixes: c7b7b483cc ("bnx2x: Don't flush multicast MACs")
Signed-off-by: Yuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, we use the fixed ACC timing 0x10804211. This is not the best
setting for each case. Actually, MTK NAND controller can adapt ACC timings
dynamically according to nfi clock frequence.
Implement the ->setup_data_interface() hook to optimize driver performance.
Signed-off-by: Xiaolei Li <xiaolei.li@mediatek.com>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
There is no need to add mtk_ecc_hw_init during ecc resume, because there
always takes mtk_ecc_wait_idle in the function mtk_ecc_enable.
Signed-off-by: Xiaolei Li <xiaolei.li@mediatek.com>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Currently, ecc encode irq is enabled when writing page with hwecc, but
we actually do not wait for this irq done. Because NFI and ECC work in
parallel, nfi irq and ecc irq almost come together.
Now, there are two steps to check whether page data are totally written.
First, wait for nfi irq INTR_AHB_DONE. This is to ensure all data
in RAM are received by NFI.
Second, polling the register NFI_ADDRCNTR till all data include ecc
parity data runtime generated by ECC are sent to NAND device.
So, it is redunant to enable ecc irq without waiting for it.
Signed-off-by: Xiaolei Li <xiaolei.li@mediatek.com>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Currently, we trigger ECC HW before setting ecc irq. It is incorrect.
Because ECC starts working once the register ECC_CTL_REG is set as
ECC_OP_ENABLE. And this may lead an abnormal behavior of ecc irq.
So, should enable ecc irq at first, then trigger ECC.
Fixes: 1d6b1e4649 ("mtd: mediatek: driver for MTK Smart Device")
Signed-off-by: Xiaolei Li <xiaolei.li@mediatek.com>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
This patch adds definition of tty_open_by_driver when CONFIG_TTY is not
defined. This was supposed to have been included in commit
12e84c71b7 ("tty: export
tty_open_by_driver"). The patch follows convention for other such
functions and returns NULL.
Signed-off-by: Okash Khawaja <okash.khawaja@gmail.com>
Reviewed-by: Samuel Thibault <samuel.thibault@ens-lyon.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
synths[] array caches currently loaded synths. synth_add checks
synths[] before adding a new one. It however ignores the result of
do_synth_init. So when do_synth_init fails, the failed synth is still
cached. Since, as a result module loading fails too, synth_remove -
which is responsible for removing the cached synth - is never called.
Next time the failing synth is added again it succeeds because
synth_add finds it cached inside synths[].
This patch fixes this by caching a synth only after do_synth_init
succeeds.
Signed-off-by: Okash Khawaja <okash.khawaja@gmail.com>
Reviewed-by: Samuel Thibault <samuel.thibault@ens-lyon.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fix checkpatch.pl warnings of the form "function definition argument
'foo' should also have an identifier name" in header files.
Signed-off-by: Derek Robson <robsonde@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fixed checkpatch.pl warnings of "function definition argument FOO should
also have an identifier name"
Found using checkpatch
Signed-off-by: Derek Robson <robsonde@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fixed checkpatch.pl warnings of the form "function definition argument
'foo' should also have an identifier name" in header files.
Signed-off-by: Derek Robson <robsonde@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We were waiting for a completion notification of HW DMA
operation using an interruptible wait which can result
in data corruption if a signal interrupted us while
DMA was not yet completed.
Fix this by moving to uninterrupted wait.
Fixes: abefd6741d ("staging: ccree: introduce CryptoCell HW driver").
Signed-off-by: Gilad Ben-Yossef <gilad@benyossef.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The ccree driver has build time configurable support
to work on top of coherent (e.g. ACP) vs. none coherent bus
connections. Turn it to run-time configurable option
based on device tree.
Signed-off-by: Gilad Ben-Yossef <gilad@benyossef.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Some SoC which implement CryptoCell have a dedicated clock
tied to it, some do not. Implement clock support if exists
based on device tree data and tie power management to it.
Signed-off-by: Gilad Ben-Yossef <gilad@benyossef.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The original ccree driver was registering a useless setkey
method even for non-MAC hash transformations. Somewhere
around v4.9 a check was added that failed hash operations
if a setkey method was registered but was not called,
so during the initial upstream port code was added to
only register the setkey method for MAC type hash transform.
Unfortunately, the ccree driver also registers non-hash based
MAC transforms and the code had a logic error that stopped
it registering a setkey callback even for those, thus rendering
them useless.
This commit fixes the logic mistake, thus correctly registering
a setkey method only for MAC transformations, leaving it out
for non-MAC ones, whether they are hash based on not.
Fixes: 50cfbbb7e6 ("staging: ccree: add ahash support").
Signed-off-by: Gilad Ben-Yossef <gilad@benyossef.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Hash import and export was saving and restoring the wrong context
and therefore disabled. Fix it by restoring intermediate digest
and additional state needed.
The hash and mac transform now pass testmgr partial hash tests.
Signed-off-by: Gilad Ben-Yossef <gilad@benyossef.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In a HVM guest the kernel allocates the page for mapping the shared
info structure via extend_brk() today. This will lead to a drop of
performance as the underlying EPT entry will have to be split up into
4kB entries as the single shared info page is located in hypervisor
memory.
The issue has been detected by using the libmicro munmap test:
unmapping 8kB of memory was faster by nearly a factor of two when no
pv interfaces were active in the HVM guest.
So instead of taking a page from memory which might be mapped via
large EPT entries use a page which is already mapped via a 4kB EPT
entry: we can take a page from the first 1MB of memory as the video
memory at 640kB disallows using larger EPT entries.
Signed-off-by: Juergen Gross <jgross@suse.com>
Reviewed-by: Boris Ostrovsky <boris.ostrovsky@oracle.com>
Signed-off-by: Juergen Gross <jgross@suse.com>
"cgroup.subtree_control" determines which resource types a cgroup
wants to control. Unlike actual resource knobs, this is an attribute
which belongs to the cgroup itself instead of its parent and thus
should be writeable by the delegatee in a delegated cgroup.
Update delegation documentation accordingly.
Signed-off-by: Tejun Heo <tj@kernel.org>
For gcc stack alignment is configured with -mpreferred-stack-boundary=N,
clang has the option -mstack-alignment=N for that purpose. Use the same
alignment as with gcc.
If the alignment is not specified clang assumes an alignment of
16 bytes, as required by the standard ABI. However as mentioned in
d9b0cde91c ("x86-64, gcc: Use -mpreferred-stack-boundary=3 if
supported") the standard kernel entry on x86-64 leaves the stack
on an 8-byte boundary, as a consequence clang will keep the stack
misaligned.
Signed-off-by: Matthias Kaehlcke <mka@chromium.org>
Acked-by: Ingo Molnar <mingo@kernel.org>
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
cc-option is used to enable compiler options for the boot code if they
are available. The macro uses KBUILD_CFLAGS and KBUILD_CPPFLAGS for the
check, however these flags aren't used to build the boot code, in
consequence cc-option can yield wrong results. For example
-mpreferred-stack-boundary=2 is never set with a 64-bit compiler,
since the setting is only valid for 16 and 32-bit binaries. This
is also the case for 32-bit kernel builds, because the option -m32 is
added to KBUILD_CFLAGS after the assignment of REALMODE_CFLAGS.
Use __cc-option instead of cc-option for the boot mode options.
The macro receives the compiler options as parameter instead of using
KBUILD_C*FLAGS, for the boot code we pass REALMODE_CFLAGS.
Also use separate statements for the __cc-option checks instead
of performing them in the initial assignment of REALMODE_CFLAGS since
the variable is an input of the macro.
Signed-off-by: Matthias Kaehlcke <mka@chromium.org>
Acked-by: Ingo Molnar <mingo@kernel.org>
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
cc-option uses KBUILD_CFLAGS and KBUILD_CPPFLAGS when it determines
whether an option is supported or not. This is fine for options used to
build the kernel itself, however some components like the x86 boot code
use a different set of flags.
Add the new macro __cc-option which is a more generic version of
cc-option with additional parameters. One parameter is the compiler
with which the check should be performed, the other the compiler options
to be used instead KBUILD_C*FLAGS.
Refactor cc-option and hostcc-option to use __cc-option and move
hostcc-option to scripts/Kbuild.include.
Suggested-by: Arnd Bergmann <arnd@arndb.de>
Suggested-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Matthias Kaehlcke <mka@chromium.org>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Michal Marek <mmarek@suse.com>
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Documentation/kbuild/makefiles.txt says the change for align options
occurred at GCC 3.0, and Documentation/process/changes.rst says the
minimal supported GCC version is 3.2, so it should be safe to hard-code
-falign* options.
Fix the only user arch/x86/Makefile_32.cpu and remove cc-option-align.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Acked-by: Ingo Molnar <mingo@kernel.org>
Turbostat has the capability to set its own affinity to
each CPU so that its MSR accesses are on the local CPU.
However, using the in-kernel cross-call in the msr driver
tends to be less invasive, so do that -- by-default.
'-m' remains to get the old behaviour.
Signed-off-by: Len Brown <len.brown@intel.com>
