* fix write+read when write has more than one byte
* remove lock, not needed on that case
* remove useless i2c msg send loop, as we support only write, read and
write+read as one go and nothing more
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Use regmap for register access. Own low level i2c read and write
routines for regmap is still needed because chip uses single command
byte in addition to typical i2c register access.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
We can simplify logging as we now have a proper i2c client
to pass for kernel dev_* logging functions.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Replace own binary division with 64-bit multiply and division.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
It shorten, as typed chars, access to config values as there is one
pointer less. Also, when config/platform data is passed to driver there
could be some values that are not relevant to store state as such or
not needed to store at all.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Driver was using wrong "8-bit" i2c addresses for demods and tuners.
Internal demod i2c address was not set at all. These are needed
to be fixed before proper i2c client binding is used.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Return EAGAIN if any of the following checks fail
+ i_rwsem is not lockable
+ NODATACOW or PREALLOC is not set
+ Cannot nocow at the desired location
+ Writing beyond end of file which is not allocated
Acked-by: David Sterba <dsterba@suse.com>
Signed-off-by: Goldwyn Rodrigues <rgoldwyn@suse.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
If IOCB_NOWAIT is set, bail if the i_rwsem is not lockable
immediately.
IF IOMAP_NOWAIT is set, return EAGAIN in xfs_file_iomap_begin
if it needs allocation either due to file extension, writing to a hole,
or COW or waiting for other DIOs to finish.
Return -EAGAIN if we don't have extent list in memory.
Signed-off-by: Goldwyn Rodrigues <rgoldwyn@suse.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Darrick J. Wong <darrick.wong@oracle.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Return EAGAIN if any of the following checks fail for direct I/O:
+ i_rwsem is lockable
+ Writing beyond end of file (will trigger allocation)
+ Blocks are not allocated at the write location
Signed-off-by: Goldwyn Rodrigues <rgoldwyn@suse.com>
Reviewed-by: Jan Kara <jack@suse.cz>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
A new bio operation flag REQ_NOWAIT is introduced to identify bio's
orignating from iocb with IOCB_NOWAIT. This flag indicates
to return immediately if a request cannot be made instead
of retrying.
Stacked devices such as md (the ones with make_request_fn hooks)
currently are not supported because it may block for housekeeping.
For example, an md can have a part of the device suspended.
For this reason, only request based devices are supported.
In the future, this feature will be expanded to stacked devices
by teaching them how to handle the REQ_NOWAIT flags.
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Goldwyn Rodrigues <rgoldwyn@suse.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
IOCB_NOWAIT translates to IOMAP_NOWAIT for iomaps.
This is used by XFS in the XFS patch.
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Jan Kara <jack@suse.cz>
Signed-off-by: Goldwyn Rodrigues <rgoldwyn@suse.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Find out if the I/O will trigger a wait due to writeback. If yes,
return -EAGAIN.
Return -EINVAL for buffered AIO: there are multiple causes of
delay such as page locks, dirty throttling logic, page loading
from disk etc. which cannot be taken care of.
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Jan Kara <jack@suse.cz>
Signed-off-by: Goldwyn Rodrigues <rgoldwyn@suse.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
RWF_NOWAIT informs kernel to bail out if an AIO request will block
for reasons such as file allocations, or a writeback triggered,
or would block while allocating requests while performing
direct I/O.
RWF_NOWAIT is translated to IOCB_NOWAIT for iocb->ki_flags.
FMODE_AIO_NOWAIT is a flag which identifies the file opened is capable
of returning -EAGAIN if the AIO call will block. This must be set by
supporting filesystems in the ->open() call.
Filesystems xfs, btrfs and ext4 would be supported in the following patches.
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Jan Kara <jack@suse.cz>
Signed-off-by: Goldwyn Rodrigues <rgoldwyn@suse.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
aio_rw_flags is introduced in struct iocb (using aio_reserved1) which will
carry the RWF_* flags. We cannot use aio_flags because they are not
checked for validity which may break existing applications.
Note, the only place RWF_HIPRI comes in effect is dio_await_one().
All the rest of the locations, aio code return -EIOCBQUEUED before the
checks for RWF_HIPRI.
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Jan Kara <jack@suse.cz>
Signed-off-by: Goldwyn Rodrigues <rgoldwyn@suse.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
filemap_range_has_page() return true if the file's mapping has
a page within the range mentioned. This function will be used
to check if a write() call will cause a writeback of previous
writes.
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Jan Kara <jack@suse.cz>
Signed-off-by: Goldwyn Rodrigues <rgoldwyn@suse.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Also added RWF_SUPPORTED to encompass all flags.
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Jan Kara <jack@suse.cz>
Signed-off-by: Goldwyn Rodrigues <rgoldwyn@suse.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Check return value from call to af9013_wr_regs(), so in case of
error print debug message and return.
Addresses-Coverity-ID: 1227035
Signed-off-by: Gustavo A. R. Silva <garsilva@embeddedor.com>
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Adds hardware IDs for all Sony CXD-based Cine-cards and MaxA8 devices, also
adds some other yet missing IDs like the Octopus V3, Octopus OEM and
Octopus Mini, as well as cards with unknown/deleted sub-ids.
Signed-off-by: Daniel Scheller <d.scheller@gmx.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Properly detect and attach Ports and Flex modules with the Sony CXD28xxER
series demods. This makes newer Cine cards and most DuoFlex C/C2/T/T2 (or
any combination of these systems) work, PCI IDs need to be added though.
Note: This utilises the CXD2841ER demod driver, which requires the changes
from this patch series to properly work. Without those changes, it won't
function properly (if at all).
Signed-off-by: Daniel Scheller <d.scheller@gmx.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Some Flex modules (mostly with anyof C/C2/T/T2 demods based on the Sony
CXD28xxER series) are equipped with an interface named XO2 (which
appears to be the Lattice MachXO2). Add functionality to detect such
links and initialise them, so any tuner module with such an interface can
be used.
This also adds dummy detection for any possible connected module, telling
the user it isn't supported at this very moment.
Also adds i2c_io(), i2c_write() and i2c_write_reg(), all required for the
XO2 handling functionality.
Signed-off-by: Daniel Scheller <d.scheller@gmx.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
This is a backport of the board control setup from the vendor provided
dddvb driver package, which does additional device initialisation based
on the board_control device info values. Also backports the TS quirk
flags which is used to control setup and usage of the tuner modules
soldered on the bridge cards (e.g. CineCTv7, CineS2 V7, MaxA8 and the
likes).
Functionality originates from ddbridge vendor driver. Permission for
reuse and kernel inclusion was formally granted by Ralph Metzler
<rjkm@metzlerbros.de>.
Cc: Ralph Metzler <rjkm@metzlerbros.de>
Signed-off-by: Daniel Scheller <d.scheller@gmx.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
On DVB-T/T2 at least, SNR might be reported as >2500dB, which not only is
just wrong but also ridiculous, so fix this by improving the conversion
of the register value.
The INTLOG10X100 function/macro and the way the values are converted were
both taken from DD's cxd2843 driver.
Signed-off-by: Daniel Scheller <d.scheller@gmx.net>
Acked-by: Abylay Ospan <aospan@netup.ru>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Bits 3 and 4 of the TSCONFIG register are important for certain hardware
constellations, in that they need to be zeroed. Add a configuration flag
to toggle this.
Signed-off-by: Daniel Scheller <d.scheller@gmx.net>
Acked-by: Abylay Ospan <aospan@netup.ru>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Adds a flag to enable or disable the IFAGCNEG bit in cxd2841er_init_tc().
Signed-off-by: Daniel Scheller <d.scheller@gmx.net>
Acked-by: Abylay Ospan <aospan@netup.ru>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Don't wait for FE_HAS_LOCK in set_frontend_tc() and thus don't hammer the
lock status register with inquiries when CXD2841ER_NO_WAIT_LOCK is set
in the configuration, which also unneccessarily blocks applications until
a TS LOCK has been acquired. Rather, API and applications will check for
a TS LOCK by utilising the tune fe_op, read_status and get_frontend ops,
which is sufficient.
Signed-off-by: Daniel Scheller <d.scheller@gmx.net>
Acked-by: Abylay Ospan <aospan@netup.ru>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
When AUTO_IFHZ is set and the tuner is supposed to provide proper IF speed
values, it should be possible to have the tuner setup take place before
the demod is configured, else the demod might be configured with either
wrong (old), or even no values at all, which obviously will cause issues.
To set this behaviour in the most flexible way, this is done with a
separate flag instead of making this depend on AUTO_IFHZ.
It should be evaluated if tuning shouldn't take place earlier in all cases
and hardware constellations.
Signed-off-by: Daniel Scheller <d.scheller@gmx.net>
Acked-by: Abylay Ospan <aospan@netup.ru>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The Sony CXD28xx demods may have other tuner types attached to them (e.g.
NXP TDA18212), so don't mandatorily configure and enable the ASCOT
functionality, but make this conditional by a config flag.
Signed-off-by: Daniel Scheller <d.scheller@gmx.net>
Acked-by: Abylay Ospan <aospan@netup.ru>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Some constellations work/need a serial TS transport mode. This adds a flag
that will toggle set up of such mode.
Signed-off-by: Daniel Scheller <d.scheller@gmx.net>
Acked-by: Abylay Ospan <aospan@netup.ru>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Add a AUTO_IFHZ flag and a function that will read IF speed values from any
attached tuner if the tuner supports this and if AUTO_IFHZ is enabled, and
else the passed default value (which probably matches Sony ASCOT tuners)
will be passed back. The returned value is then used to calculate the iffeq
which the demod will be programmed with.
Signed-off-by: Daniel Scheller <d.scheller@gmx.net>
Acked-by: Abylay Ospan <aospan@netup.ru>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Some cards/bridges wrap i2c_gate_ctrl handling with a mutex_lock(). This is
e.g. done in ddbridge to protect against concurrent tuner access with
regards to the dual tuner HW, where concurrent tuner reconfiguration can
result in tuning fails or bad reception quality. When the tuner driver
additionally tries to open the I2C gate (which e.g. the tda18212 driver
does) when the demod already did this, this will lead to a deadlock. This
makes the calls to i2c_gatectrl from the demod driver optional when the
flag is set, leaving this to the tuner driver. For readability reasons and
to not have the check duplicated multiple times, the setup is factored
into cxd2841er_tuner_set().
This commit also updates the netup card driver (which seems to be the only
consumer of the cxd2841er as of now).
Signed-off-by: Daniel Scheller <d.scheller@gmx.net>
Acked-by: Abylay Ospan <aospan@netup.ru>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Throughout the patch series some configuration flags will be added to the
demod driver. This patch prepares this by adding the flags var to
struct cxd2841er_config, which will serve as a bitmask to toggle various
options and behaviour in the driver.
Signed-off-by: Daniel Scheller <d.scheller@gmx.net>
Acked-by: Abylay Ospan <aospan@netup.ru>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The way the MAKE_IFFREQ_CONFIG macros are written make it impossible to
pass regular integers for iffreq calculation, since this will cause "SSE
register return with SSE disabled" compile errors. This changes the
calculation into C functions which also might help when debugging. Also,
expand all passed frequencies from MHz to Hz scale.
Signed-off-by: Daniel Scheller <d.scheller@gmx.net>
Acked-by: Abylay Ospan <aospan@netup.ru>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Those demods are programmed in the same way as the CXD2841ER/54ER and can
be handled by this driver. Support added in a way matching the existing
code, supported delivery systems are set according to what each demod
supports.
Updates the type string setting used for printing the "attaching..." log
line aswell.
Signed-off-by: Daniel Scheller <d.scheller@gmx.net>
Acked-by: Abylay Ospan <aospan@netup.ru>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Do unfreeze_regs() directly when accessing the demod registers is done,
and don't have multiple unfreeze's on different conditions, which even
can get prone to errors.
Signed-off-by: Daniel Scheller <d.scheller@gmx.net>
Acked-by: Abylay Ospan <aospan@netup.ru>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Doing the I2C read operation with two calls to i2c_transfer() causes the
exclusive I2C bus lock of the underlying adapter to be released. While this
isn't an issue if only one demodulator is attached to the bus, having two
or even more causes troubles in that concurrent accesses to the different
demods will cause all kinds of issues due to wrong data being returned on
read operations (for example, the TS config register will be set wrong).
This changes the read_regs() function to do the operation in one go (by
calling i2c_transfer with the whole msg list instead of one by one) to not
loose the I2C bus lock, fixing all sorts of random runtime failures.
Signed-off-by: Daniel Scheller <d.scheller@gmx.net>
Acked-by: Abylay Ospan <aospan@netup.ru>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
This moves the I2C debug dump into the preceding dev_dbg() call by
utilising the %*ph format macro and removes the call to
print_hex_debug_bytes().
Signed-off-by: Daniel Scheller <d.scheller@gmx.net>
Acked-by: Abylay Ospan <aospan@netup.ru>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The latest documentation reveals that initial voltage range that is
supported is starting from 0.6V for all the PMICs belonging to lp87565
family. Fix the same.
Signed-off-by: Keerthy <j-keerthy@ti.com>
Fixes: f0168a9bf ("regulator: lp87565: Add support for lp87565 PMIC regulators")
Signed-off-by: Mark Brown <broonie@kernel.org>
* fix problems that could cause hangs or crashes in the host on POWER9
* fix problems that could allow guests to potentially affect or disrupt
the execution of the controlling userspace
This adds detection and activation for STV0367-based tuner hardware (namely
CineCTv6 bridge cards and older DuoFlex CT addon modules). Utilises the
extended stv0367 demod driver.
TDA18212 i2c_client/regmap-api code was originally implemented by
Antti Palosaari <crope@iki.fi> in a variant to update the ddbridge code
from the vendor dddvb package (formal ack for these parts received).
Original patch at [1].
When boards with STV0367 are cold-started, there might be issues with the
I2C gate, causing the TDA18212 detection/probe to fail. For these demods,
a workaround (tuner_tda18212_ping) is implemented which probes the tuner
twice on this hardware constellation which will resolve the problem and
put all components into a working state. Other demod/port types won't be
retried.
[1] https://patchwork.linuxtv.org/patch/25146/
Signed-off-by: Daniel Scheller <d.scheller@gmx.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Adds new i2c_read_regs() function and make i2c_read_reg() wrap into this
with len=1. Required for the tuner_tda18212_ping() and XO2 handling
functions (part of the Sony CXD28xx support patch series).
Signed-off-by: Daniel Scheller <d.scheller@gmx.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
This - in conjunction with the previous changes - makes it possible to use
the STV0367 DVB-C/T demodulator driver with Digital Devices hardware having
this demodulator soldered on them (namely CineCTv6 bridges and some earlier
DuoFlex CT addon modules).
The changes do the following:
- add a third *_attach function which will make use of a third frontend_ops
struct which announces both -C and -T support (the same as with DD's own
driver stv0367dd). This is necessary to support both delivery systems
on one FE without having to do large conversions to VB2 or the need to
select either -C or -T mode via modparams and the like. Additionally,
the frontend_ops point to new "glue" functions which will then call into
the existing functionality depending on the active delivery system/demod
state (all used functionality works almost OOTB).
- Demod initialisation has been ported from stv0367dd. DD's driver always
does a full init of both OFDM and QAM cores, with some additional things.
The active delivery system is remembered and upon switch, the Demod will
be reconfigured to work in OFDM or QAM mode (that's what the ddb_setup_XX
functions are used for). Note that in QAM mode, the DD demods work with
an IC speed of 58Mhz. It's not very good to perform full reinits upon
Demod mode changes since in very rare occasions this can lead to the I2C
interface or the whole Demod to crash, requiring a powercycle, thus the
flag to perform full reinit is set to disabled.
- A little enum is added for named identifiers of the current Demod state.
Initialisation code/register writes originate from stv0367dd. Permission
to reuse was formally granted by Ralph Metzler <rjkm@metzlerbros.de>.
Signed-off-by: Daniel Scheller <d.scheller@gmx.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Digital Devices uses defaults tables in their stv0367dd demod driver
variant which differ in a few registers, at least enough that no stable
operation can be provided with the tables already present in the driver
(init succeeds and DVB reception works but at least when the driver is
reloaded using rmmod/modprobe, the demod goes into a crashed state in a
way it doesn't react on any I2C command anymore, while even more
side-effects may occur), so there's a good reason to better have another
set of defaults.
Defaults originating from the stv0367dd driver. Permission to reuse them
was formally granted by Ralph Metzler <rjkm@metzlerbros.de>.
Signed-off-by: Daniel Scheller <d.scheller@gmx.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The values used for comparing symbol rates and the resulting conditional
reg writes seem wrong (rates multiplied by ten), so fix those values.
While this doesn't seem to influence operation, it should be fixed anyway.
Signed-off-by: Daniel Scheller <d.scheller@gmx.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
In some configurations (due to different PIN config, wiring or so), the
QAM FECLock might be signalled using a different register than
F367CAB_QAMFEC_LOCK (e.g. F367CAB_DESCR_SYNCSTATE on Digital Devices hw),
so make that register selectable.
Signed-off-by: Daniel Scheller <d.scheller@gmx.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
