Changes in 5.15.36
fs: remove __sync_filesystem
block: remove __sync_blockdev
block: simplify the block device syncing code
vfs: make sync_filesystem return errors from ->sync_fs
xfs: return errors in xfs_fs_sync_fs
dma-mapping: remove bogus test for pfn_valid from dma_map_resource
arm64/mm: drop HAVE_ARCH_PFN_VALID
etherdevice: Adjust ether_addr* prototypes to silence -Wstringop-overead
mm: page_alloc: fix building error on -Werror=array-compare
perf tools: Fix segfault accessing sample_id xyarray
mm, kfence: support kmem_dump_obj() for KFENCE objects
gfs2: assign rgrp glock before compute_bitstructs
scsi: ufs: core: scsi_get_lba() error fix
net/sched: cls_u32: fix netns refcount changes in u32_change()
ALSA: usb-audio: Clear MIDI port active flag after draining
ALSA: hda/realtek: Add quirk for Clevo NP70PNP
ASoC: atmel: Remove system clock tree configuration for at91sam9g20ek
ASoC: topology: Correct error handling in soc_tplg_dapm_widget_create()
ASoC: rk817: Use devm_clk_get() in rk817_platform_probe
ASoC: msm8916-wcd-digital: Check failure for devm_snd_soc_register_component
ASoC: codecs: wcd934x: do not switch off SIDO Buck when codec is in use
dmaengine: idxd: fix device cleanup on disable
dmaengine: imx-sdma: Fix error checking in sdma_event_remap
dmaengine: mediatek:Fix PM usage reference leak of mtk_uart_apdma_alloc_chan_resources
dmaengine: dw-edma: Fix unaligned 64bit access
spi: spi-mtk-nor: initialize spi controller after resume
esp: limit skb_page_frag_refill use to a single page
spi: cadence-quadspi: fix incorrect supports_op() return value
igc: Fix infinite loop in release_swfw_sync
igc: Fix BUG: scheduling while atomic
igc: Fix suspending when PTM is active
ALSA: hda/hdmi: fix warning about PCM count when used with SOF
rxrpc: Restore removed timer deletion
net/smc: Fix sock leak when release after smc_shutdown()
net/packet: fix packet_sock xmit return value checking
ip6_gre: Avoid updating tunnel->tun_hlen in __gre6_xmit()
ip6_gre: Fix skb_under_panic in __gre6_xmit()
net: restore alpha order to Ethernet devices in config
net/sched: cls_u32: fix possible leak in u32_init_knode()
l3mdev: l3mdev_master_upper_ifindex_by_index_rcu should be using netdev_master_upper_dev_get_rcu
ipv6: make ip6_rt_gc_expire an atomic_t
can: isotp: stop timeout monitoring when no first frame was sent
net: dsa: hellcreek: Calculate checksums in tagger
net: mscc: ocelot: fix broken IP multicast flooding
netlink: reset network and mac headers in netlink_dump()
drm/i915/display/psr: Unset enable_psr2_sel_fetch if other checks in intel_psr2_config_valid() fails
net: stmmac: Use readl_poll_timeout_atomic() in atomic state
dmaengine: idxd: add RO check for wq max_batch_size write
dmaengine: idxd: add RO check for wq max_transfer_size write
dmaengine: idxd: skip clearing device context when device is read-only
selftests: mlxsw: vxlan_flooding: Prevent flooding of unwanted packets
arm64: mm: fix p?d_leaf()
ARM: vexpress/spc: Avoid negative array index when !SMP
reset: renesas: Check return value of reset_control_deassert()
reset: tegra-bpmp: Restore Handle errors in BPMP response
platform/x86: samsung-laptop: Fix an unsigned comparison which can never be negative
ALSA: usb-audio: Fix undefined behavior due to shift overflowing the constant
drm/msm/disp: check the return value of kzalloc()
arm64: dts: imx: Fix imx8*-var-som touchscreen property sizes
vxlan: fix error return code in vxlan_fdb_append
cifs: Check the IOCB_DIRECT flag, not O_DIRECT
net: atlantic: Avoid out-of-bounds indexing
mt76: Fix undefined behavior due to shift overflowing the constant
brcmfmac: sdio: Fix undefined behavior due to shift overflowing the constant
dpaa_eth: Fix missing of_node_put in dpaa_get_ts_info()
drm/msm/mdp5: check the return of kzalloc()
net: macb: Restart tx only if queue pointer is lagging
scsi: iscsi: Release endpoint ID when its freed
scsi: iscsi: Merge suspend fields
scsi: iscsi: Fix NOP handling during conn recovery
scsi: qedi: Fix failed disconnect handling
stat: fix inconsistency between struct stat and struct compat_stat
VFS: filename_create(): fix incorrect intent.
nvme: add a quirk to disable namespace identifiers
nvme-pci: disable namespace identifiers for the MAXIO MAP1002/1202
nvme-pci: disable namespace identifiers for Qemu controllers
EDAC/synopsys: Read the error count from the correct register
mm/memory-failure.c: skip huge_zero_page in memory_failure()
memcg: sync flush only if periodic flush is delayed
mm, hugetlb: allow for "high" userspace addresses
oom_kill.c: futex: delay the OOM reaper to allow time for proper futex cleanup
mm/mmu_notifier.c: fix race in mmu_interval_notifier_remove()
ata: pata_marvell: Check the 'bmdma_addr' beforing reading
dma: at_xdmac: fix a missing check on list iterator
dmaengine: imx-sdma: fix init of uart scripts
net: atlantic: invert deep par in pm functions, preventing null derefs
Input: omap4-keypad - fix pm_runtime_get_sync() error checking
scsi: sr: Do not leak information in ioctl
sched/pelt: Fix attach_entity_load_avg() corner case
perf/core: Fix perf_mmap fail when CONFIG_PERF_USE_VMALLOC enabled
drm/panel/raspberrypi-touchscreen: Avoid NULL deref if not initialised
drm/panel/raspberrypi-touchscreen: Initialise the bridge in prepare
KVM: PPC: Fix TCE handling for VFIO
drm/vc4: Use pm_runtime_resume_and_get to fix pm_runtime_get_sync() usage
powerpc/perf: Fix power9 event alternatives
powerpc/perf: Fix power10 event alternatives
perf script: Always allow field 'data_src' for auxtrace
perf report: Set PERF_SAMPLE_DATA_SRC bit for Arm SPE event
xtensa: patch_text: Fixup last cpu should be master
xtensa: fix a7 clobbering in coprocessor context load/store
openvswitch: fix OOB access in reserve_sfa_size()
gpio: Request interrupts after IRQ is initialized
ASoC: soc-dapm: fix two incorrect uses of list iterator
e1000e: Fix possible overflow in LTR decoding
ARC: entry: fix syscall_trace_exit argument
arm_pmu: Validate single/group leader events
KVM: x86/pmu: Update AMD PMC sample period to fix guest NMI-watchdog
KVM: x86: Pend KVM_REQ_APICV_UPDATE during vCPU creation to fix a race
KVM: nVMX: Defer APICv updates while L2 is active until L1 is active
KVM: SVM: Flush when freeing encrypted pages even on SME_COHERENT CPUs
netfilter: conntrack: convert to refcount_t api
netfilter: conntrack: avoid useless indirection during conntrack destruction
ext4: fix fallocate to use file_modified to update permissions consistently
ext4: fix symlink file size not match to file content
ext4: fix use-after-free in ext4_search_dir
ext4: limit length to bitmap_maxbytes - blocksize in punch_hole
ext4, doc: fix incorrect h_reserved size
ext4: fix overhead calculation to account for the reserved gdt blocks
ext4: force overhead calculation if the s_overhead_cluster makes no sense
netfilter: nft_ct: fix use after free when attaching zone template
jbd2: fix a potential race while discarding reserved buffers after an abort
spi: atmel-quadspi: Fix the buswidth adjustment between spi-mem and controller
block/compat_ioctl: fix range check in BLKGETSIZE
arm64: dts: qcom: add IPA qcom,qmp property
Linux 5.15.36
Signed-off-by: Greg Kroah-Hartman <gregkh@google.com>
Change-Id: Iba23a60bda8fd07f26fd7f9217f208c2e6ee26c2
commit 2dfe63e61cc31ee59ce951672b0850b5229cd5b0 upstream.
Calling kmem_obj_info() via kmem_dump_obj() on KFENCE objects has been
producing garbage data due to the object not actually being maintained
by SLAB or SLUB.
Fix this by implementing __kfence_obj_info() that copies relevant
information to struct kmem_obj_info when the object was allocated by
KFENCE; this is called by a common kmem_obj_info(), which also calls the
slab/slub/slob specific variant now called __kmem_obj_info().
For completeness, kmem_dump_obj() now displays if the object was
allocated by KFENCE.
Link: https://lore.kernel.org/all/20220323090520.GG16885@xsang-OptiPlex-9020/
Link: https://lkml.kernel.org/r/20220406131558.3558585-1-elver@google.com
Fixes: b89fb5ef0c ("mm, kfence: insert KFENCE hooks for SLUB")
Fixes: d3fb45f370 ("mm, kfence: insert KFENCE hooks for SLAB")
Signed-off-by: Marco Elver <elver@google.com>
Reviewed-by: Hyeonggon Yoo <42.hyeyoo@gmail.com>
Reported-by: kernel test robot <oliver.sang@intel.com>
Acked-by: Vlastimil Babka <vbabka@suse.cz> [slab]
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
(Backport: adjacent lines changed in kmem_cache_destroy.)
Because mm/slab_common.c is not instrumented with software KASAN modes,
it is not possible to detect use-after-free of the kmem_cache passed
into kmem_cache_destroy(). In particular, because of the s->refcount--
and subsequent early return if non-zero, KASAN would never be able to
see the double-free via kmem_cache_free(kmem_cache, s). To be able to
detect a double-kmem_cache_destroy(), check accessibility of the
kmem_cache, and in case of failure return early.
While KASAN_HW_TAGS is able to detect such bugs, by checking
accessibility and returning early we fail more gracefully and also avoid
corrupting reused objects (where tags mismatch).
A recent case of a double-kmem_cache_destroy() was detected by KFENCE:
https://lkml.kernel.org/r/0000000000003f654905c168b09d@google.com, which
was not detectable by software KASAN modes.
Link: https://lkml.kernel.org/r/20211119142219.1519617-1-elver@google.com
Signed-off-by: Marco Elver <elver@google.com>
Acked-by: Vlastimil Babka <vbabka@suse.cz>
Reviewed-by: Andrey Konovalov <andreyknvl@gmail.com>
Cc: Alexander Potapenko <glider@google.com>
Cc: Andrey Ryabinin <ryabinin.a.a@gmail.com>
Cc: Christoph Lameter <cl@linux.com>
Cc: David Rientjes <rientjes@google.com>
Cc: Dmitry Vyukov <dvyukov@google.com>
Cc: Joonsoo Kim <iamjoonsoo.kim@lge.com>
Cc: Pekka Enberg <penberg@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
(cherry picked from commit bed0a9b591492bb285ea88cd221e0412031396ca)
Bug: 217222520
Change-Id: I6a3cbe5b92ea806c7c1e447a64c5f36abd679593
Signed-off-by: Andrey Konovalov <andreyknvl@google.com>
flush_all() flushes a specific SLAB cache on each CPU (where the cache
is present). The deactivate_slab()/__free_slab() invocation happens
within IPI handler and is problematic for PREEMPT_RT.
The flush operation is not a frequent operation or a hot path. The
per-CPU flush operation can be moved to within a workqueue.
Because a workqueue handler, unlike IPI handler, does not disable irqs,
flush_slab() now has to disable them for working with the kmem_cache_cpu
fields. deactivate_slab() is safe to call with irqs enabled.
[vbabka@suse.cz: adapt to new SLUB changes]
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Vlastimil Babka <vbabka@suse.cz>
Pull RCU updates from Paul McKenney:
- Bitmap parsing support for "all" as an alias for all bits
- Documentation updates
- Miscellaneous fixes, including some that overlap into mm and lockdep
- kvfree_rcu() updates
- mem_dump_obj() updates, with acks from one of the slab-allocator
maintainers
- RCU NOCB CPU updates, including limited deoffloading
- SRCU updates
- Tasks-RCU updates
- Torture-test updates
* 'core-rcu-2021.07.04' of git://git.kernel.org/pub/scm/linux/kernel/git/paulmck/linux-rcu: (78 commits)
tasks-rcu: Make show_rcu_tasks_gp_kthreads() be static inline
rcu-tasks: Make ksoftirqd provide RCU Tasks quiescent states
rcu: Add missing __releases() annotation
rcu: Remove obsolete rcu_read_unlock() deadlock commentary
rcu: Improve comments describing RCU read-side critical sections
rcu: Create an unrcu_pointer() to remove __rcu from a pointer
srcu: Early test SRCU polling start
rcu: Fix various typos in comments
rcu/nocb: Unify timers
rcu/nocb: Prepare for fine-grained deferred wakeup
rcu/nocb: Only cancel nocb timer if not polling
rcu/nocb: Delete bypass_timer upon nocb_gp wakeup
rcu/nocb: Cancel nocb_timer upon nocb_gp wakeup
rcu/nocb: Allow de-offloading rdp leader
rcu/nocb: Directly call __wake_nocb_gp() from bypass timer
rcu: Don't penalize priority boosting when there is nothing to boost
rcu: Point to documentation of ordering guarantees
rcu: Make rcu_gp_cleanup() be noinline for tracing
rcu: Restrict RCU_STRICT_GRACE_PERIOD to at most four CPUs
rcu: Make show_rcu_gp_kthreads() dump rcu_node structures blocking GP
...
There are currently two problems in the way the objcg pointer array
(memcg_data) in the page structure is being allocated and freed.
On its allocation, it is possible that the allocated objcg pointer
array comes from the same slab that requires memory accounting. If this
happens, the slab will never become empty again as there is at least
one object left (the obj_cgroup array) in the slab.
When it is freed, the objcg pointer array object may be the last one
in its slab and hence causes kfree() to be called again. With the
right workload, the slab cache may be set up in a way that allows the
recursive kfree() calling loop to nest deep enough to cause a kernel
stack overflow and panic the system.
One way to solve this problem is to split the kmalloc-<n> caches
(KMALLOC_NORMAL) into two separate sets - a new set of kmalloc-<n>
(KMALLOC_NORMAL) caches for unaccounted objects only and a new set of
kmalloc-cg-<n> (KMALLOC_CGROUP) caches for accounted objects only. All
the other caches can still allow a mix of accounted and unaccounted
objects.
With this change, all the objcg pointer array objects will come from
KMALLOC_NORMAL caches which won't have their objcg pointer arrays. So
both the recursive kfree() problem and non-freeable slab problem are
gone.
Since both the KMALLOC_NORMAL and KMALLOC_CGROUP caches no longer have
mixed accounted and unaccounted objects, this will slightly reduce the
number of objcg pointer arrays that need to be allocated and save a bit
of memory. On the other hand, creating a new set of kmalloc caches does
have the effect of reducing cache utilization. So it is properly a wash.
The new KMALLOC_CGROUP is added between KMALLOC_NORMAL and
KMALLOC_RECLAIM so that the first for loop in create_kmalloc_caches()
will include the newly added caches without change.
[vbabka@suse.cz: don't create kmalloc-cg caches with cgroup.memory=nokmem]
Link: https://lkml.kernel.org/r/20210512145107.6208-1-longman@redhat.com
[akpm@linux-foundation.org: un-fat-finger v5 delta creation]
[longman@redhat.com: disable cache merging for KMALLOC_NORMAL caches]
Link: https://lkml.kernel.org/r/20210505200610.13943-4-longman@redhat.com
Link: https://lkml.kernel.org/r/20210512145107.6208-1-longman@redhat.com
Link: https://lkml.kernel.org/r/20210505200610.13943-3-longman@redhat.com
Signed-off-by: Waiman Long <longman@redhat.com>
Signed-off-by: Vlastimil Babka <vbabka@suse.cz>
Suggested-by: Vlastimil Babka <vbabka@suse.cz>
Reviewed-by: Shakeel Butt <shakeelb@google.com>
Acked-by: Roman Gushchin <guro@fb.com>
Cc: Christoph Lameter <cl@linux.com>
Cc: David Rientjes <rientjes@google.com>
Cc: Johannes Weiner <hannes@cmpxchg.org>
Cc: Joonsoo Kim <iamjoonsoo.kim@lge.com>
Cc: Michal Hocko <mhocko@kernel.org>
Cc: Pekka Enberg <penberg@kernel.org>
Cc: Vladimir Davydov <vdavydov.dev@gmail.com>
[longman@redhat.com: fix for CONFIG_ZONE_DMA=n]
Suggested-by: Roman Gushchin <guro@fb.com>
Reviewed-by: Vlastimil Babka <vbabka@suse.cz>
Cc: Vladimir Davydov <vdavydov.dev@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The redzone area for SLUB exists between s->object_size and s->inuse
(which is at least the word-aligned object_size). If a cache were
created with an object_size smaller than sizeof(void *), the in-object
stored freelist pointer would overwrite the redzone (e.g. with boot
param "slub_debug=ZF"):
BUG test (Tainted: G B ): Right Redzone overwritten
-----------------------------------------------------------------------------
INFO: 0xffff957ead1c05de-0xffff957ead1c05df @offset=1502. First byte 0x1a instead of 0xbb
INFO: Slab 0xffffef3950b47000 objects=170 used=170 fp=0x0000000000000000 flags=0x8000000000000200
INFO: Object 0xffff957ead1c05d8 @offset=1496 fp=0xffff957ead1c0620
Redzone (____ptrval____): bb bb bb bb bb bb bb bb ........
Object (____ptrval____): f6 f4 a5 40 1d e8 ...@..
Redzone (____ptrval____): 1a aa ..
Padding (____ptrval____): 00 00 00 00 00 00 00 00 ........
Store the freelist pointer out of line when object_size is smaller than
sizeof(void *) and redzoning is enabled.
Additionally remove the "smaller than sizeof(void *)" check under
CONFIG_DEBUG_VM in kmem_cache_sanity_check() as it is now redundant:
SLAB and SLOB both handle small sizes.
(Note that no caches within this size range are known to exist in the
kernel currently.)
Link: https://lkml.kernel.org/r/20210608183955.280836-3-keescook@chromium.org
Fixes: 81819f0fc8 ("SLUB core")
Signed-off-by: Kees Cook <keescook@chromium.org>
Acked-by: Vlastimil Babka <vbabka@suse.cz>
Cc: Christoph Lameter <cl@linux.com>
Cc: David Rientjes <rientjes@google.com>
Cc: Joonsoo Kim <iamjoonsoo.kim@lge.com>
Cc: "Lin, Zhenpeng" <zplin@psu.edu>
Cc: Marco Elver <elver@google.com>
Cc: Pekka Enberg <penberg@kernel.org>
Cc: Roman Gushchin <guro@fb.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Paul E. McKenney reported [1] that commit 1f0723a4c0 ("mm, slub: enable
slub_debug static key when creating cache with explicit debug flags")
results in the lockdep complaint:
======================================================
WARNING: possible circular locking dependency detected
5.12.0+ #15 Not tainted
------------------------------------------------------
rcu_torture_sta/109 is trying to acquire lock:
ffffffff96063cd0 (cpu_hotplug_lock){++++}-{0:0}, at: static_key_enable+0x9/0x20
but task is already holding lock:
ffffffff96173c28 (slab_mutex){+.+.}-{3:3}, at: kmem_cache_create_usercopy+0x2d/0x250
which lock already depends on the new lock.
the existing dependency chain (in reverse order) is:
-> #1 (slab_mutex){+.+.}-{3:3}:
lock_acquire+0xb9/0x3a0
__mutex_lock+0x8d/0x920
slub_cpu_dead+0x15/0xf0
cpuhp_invoke_callback+0x17a/0x7c0
cpuhp_invoke_callback_range+0x3b/0x80
_cpu_down+0xdf/0x2a0
cpu_down+0x2c/0x50
device_offline+0x82/0xb0
remove_cpu+0x1a/0x30
torture_offline+0x80/0x140
torture_onoff+0x147/0x260
kthread+0x10a/0x140
ret_from_fork+0x22/0x30
-> #0 (cpu_hotplug_lock){++++}-{0:0}:
check_prev_add+0x8f/0xbf0
__lock_acquire+0x13f0/0x1d80
lock_acquire+0xb9/0x3a0
cpus_read_lock+0x21/0xa0
static_key_enable+0x9/0x20
__kmem_cache_create+0x38d/0x430
kmem_cache_create_usercopy+0x146/0x250
kmem_cache_create+0xd/0x10
rcu_torture_stats+0x79/0x280
kthread+0x10a/0x140
ret_from_fork+0x22/0x30
other info that might help us debug this:
Possible unsafe locking scenario:
CPU0 CPU1
---- ----
lock(slab_mutex);
lock(cpu_hotplug_lock);
lock(slab_mutex);
lock(cpu_hotplug_lock);
*** DEADLOCK ***
1 lock held by rcu_torture_sta/109:
#0: ffffffff96173c28 (slab_mutex){+.+.}-{3:3}, at: kmem_cache_create_usercopy+0x2d/0x250
stack backtrace:
CPU: 3 PID: 109 Comm: rcu_torture_sta Not tainted 5.12.0+ #15
Hardware name: QEMU Standard PC (Q35 + ICH9, 2009), BIOS 1.13.0-1ubuntu1.1 04/01/2014
Call Trace:
dump_stack+0x6d/0x89
check_noncircular+0xfe/0x110
? lock_is_held_type+0x98/0x110
check_prev_add+0x8f/0xbf0
__lock_acquire+0x13f0/0x1d80
lock_acquire+0xb9/0x3a0
? static_key_enable+0x9/0x20
? mark_held_locks+0x49/0x70
cpus_read_lock+0x21/0xa0
? static_key_enable+0x9/0x20
static_key_enable+0x9/0x20
__kmem_cache_create+0x38d/0x430
kmem_cache_create_usercopy+0x146/0x250
? rcu_torture_stats_print+0xd0/0xd0
kmem_cache_create+0xd/0x10
rcu_torture_stats+0x79/0x280
? rcu_torture_stats_print+0xd0/0xd0
kthread+0x10a/0x140
? kthread_park+0x80/0x80
ret_from_fork+0x22/0x30
This is because there's one order of locking from the hotplug callbacks:
lock(cpu_hotplug_lock); // from hotplug machinery itself
lock(slab_mutex); // in e.g. slab_mem_going_offline_callback()
And commit 1f0723a4c0 made the reverse sequence possible:
lock(slab_mutex); // in kmem_cache_create_usercopy()
lock(cpu_hotplug_lock); // kmem_cache_open() -> static_key_enable()
The simplest fix is to move static_key_enable() to a place before slab_mutex is
taken. That means kmem_cache_create_usercopy() in mm/slab_common.c which is not
ideal for SLUB-specific code, but the #ifdef CONFIG_SLUB_DEBUG makes it
at least self-contained and obvious.
[1] https://lore.kernel.org/lkml/20210502171827.GA3670492@paulmck-ThinkPad-P17-Gen-1/
Link: https://lkml.kernel.org/r/20210504120019.26791-1-vbabka@suse.cz
Fixes: 1f0723a4c0 ("mm, slub: enable slub_debug static key when creating cache with explicit debug flags")
Signed-off-by: Vlastimil Babka <vbabka@suse.cz>
Reported-by: Paul E. McKenney <paulmck@kernel.org>
Tested-by: Paul E. McKenney <paulmck@kernel.org>
Acked-by: David Rientjes <rientjes@google.com>
Cc: Christoph Lameter <cl@linux.com>
Cc: Pekka Enberg <penberg@kernel.org>
Cc: Joonsoo Kim <iamjoonsoo.kim@lge.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This commit adds a few crude tests for mem_dump_obj() to rcutorture
runs. Just to prevent bitrot, you understand!
Signed-off-by: Paul E. McKenney <paulmck@kernel.org>
The mem_dump_obj() functionality adds a few hundred bytes, which is a
small price to pay. Except on kernels built with CONFIG_PRINTK=n, in
which mem_dump_obj() messages will be suppressed. This commit therefore
makes mem_dump_obj() be a static inline empty function on kernels built
with CONFIG_PRINTK=n and excludes all of its support functions as well.
This avoids kernel bloat on systems that cannot use mem_dump_obj().
Cc: Christoph Lameter <cl@linux.com>
Cc: Pekka Enberg <penberg@kernel.org>
Cc: David Rientjes <rientjes@google.com>
Cc: Joonsoo Kim <iamjoonsoo.kim@lge.com>
Cc: <linux-mm@kvack.org>
Suggested-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Paul E. McKenney <paulmck@kernel.org>
Patch series "kasan: optimizations and fixes for HW_TAGS", v4.
This patchset makes the HW_TAGS mode more efficient, mostly by reworking
poisoning approaches and simplifying/inlining some internal helpers.
With this change, the overhead of HW_TAGS annotations excluding setting
and checking memory tags is ~3%. The performance impact caused by tags
will be unknown until we have hardware that supports MTE.
As a side-effect, this patchset speeds up generic KASAN by ~15%.
This patch (of 13):
Currently KASAN saves allocation stacks in both kasan_slab_alloc() and
kasan_kmalloc() annotations. This patch changes KASAN to save allocation
stacks for slab objects from kmalloc caches in kasan_kmalloc() only, and
stacks for other slab objects in kasan_slab_alloc() only.
This change requires ____kasan_kmalloc() knowing whether the object
belongs to a kmalloc cache. This is implemented by adding a flag field to
the kasan_info structure. That flag is only set for kmalloc caches via a
new kasan_cache_create_kmalloc() annotation.
Link: https://lkml.kernel.org/r/cover.1612546384.git.andreyknvl@google.com
Link: https://lkml.kernel.org/r/7c673ebca8d00f40a7ad6f04ab9a2bddeeae2097.1612546384.git.andreyknvl@google.com
Signed-off-by: Andrey Konovalov <andreyknvl@google.com>
Reviewed-by: Marco Elver <elver@google.com>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Vincenzo Frascino <vincenzo.frascino@arm.com>
Cc: Dmitry Vyukov <dvyukov@google.com>
Cc: Alexander Potapenko <glider@google.com>
Cc: Will Deacon <will.deacon@arm.com>
Cc: Andrey Ryabinin <aryabinin@virtuozzo.com>
Cc: Peter Collingbourne <pcc@google.com>
Cc: Evgenii Stepanov <eugenis@google.com>
Cc: Branislav Rankov <Branislav.Rankov@arm.com>
Cc: Kevin Brodsky <kevin.brodsky@arm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The currently existing kasan_check_read/write() annotations are intended
to be used for kernel modules that have KASAN compiler instrumentation
disabled. Thus, they are only relevant for the software KASAN modes that
rely on compiler instrumentation.
However there's another use case for these annotations: ksize() checks
that the object passed to it is indeed accessible before unpoisoning the
whole object. This is currently done via __kasan_check_read(), which is
compiled away for the hardware tag-based mode that doesn't rely on
compiler instrumentation. This leads to KASAN missing detecting some
memory corruptions.
Provide another annotation called kasan_check_byte() that is available
for all KASAN modes. As the implementation rename and reuse
kasan_check_invalid_free(). Use this new annotation in ksize().
To avoid having ksize() as the top frame in the reported stack trace
pass _RET_IP_ to __kasan_check_byte().
Also add a new ksize_uaf() test that checks that a use-after-free is
detected via ksize() itself, and via plain accesses that happen later.
Link: https://linux-review.googlesource.com/id/Iaabf771881d0f9ce1b969f2a62938e99d3308ec5
Link: https://lkml.kernel.org/r/f32ad74a60b28d8402482a38476f02bb7600f620.1610733117.git.andreyknvl@google.com
Signed-off-by: Andrey Konovalov <andreyknvl@google.com>
Reviewed-by: Marco Elver <elver@google.com>
Reviewed-by: Alexander Potapenko <glider@google.com>
Cc: Andrey Ryabinin <aryabinin@virtuozzo.com>
Cc: Branislav Rankov <Branislav.Rankov@arm.com>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Dmitry Vyukov <dvyukov@google.com>
Cc: Evgenii Stepanov <eugenis@google.com>
Cc: Kevin Brodsky <kevin.brodsky@arm.com>
Cc: Peter Collingbourne <pcc@google.com>
Cc: Vincenzo Frascino <vincenzo.frascino@arm.com>
Cc: Will Deacon <will.deacon@arm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
SLAB has been using get/put_online_cpus() around creating, destroying and
shrinking kmem caches since 95402b3829 ("cpu-hotplug: replace
per-subsystem mutexes with get_online_cpus()") in 2008, which is supposed
to be replacing a private mutex (cache_chain_mutex, called slab_mutex
today) with system-wide mechanism, but in case of SLAB it's in fact used
in addition to the existing mutex, without explanation why.
SLUB appears to have avoided the cpu hotplug lock initially, but gained it
due to common code unification, such as 20cea9683e ("mm, sl[aou]b: Move
kmem_cache_create mutex handling to common code").
Regardless of the history, checking if the hotplug lock is actually needed
today suggests that it's not, and therefore it's better to avoid this
system-wide lock and the ordering this imposes wrt other locks (such as
slab_mutex).
Specifically, in SLAB we have for_each_online_cpu() in do_tune_cpucache()
protected by slab_mutex, and cpu hotplug callbacks that also take the
slab_mutex, which is also taken by the common slab function that currently
also take the hotplug lock. Thus the slab_mutex protection should be
sufficient. Also per-cpu array caches are allocated for each possible
cpu, so not affected by their online/offline state.
In SLUB we have for_each_online_cpu() in functions that show statistics
and are already unprotected today, as racing with hotplug is not harmful.
Otherwise SLUB relies on percpu allocator. The slub_cpu_dead() hotplug
callback takes the slab_mutex.
To sum up, this patch removes get/put_online_cpus() calls from slab as it
should be safe without further adjustments.
Link: https://lkml.kernel.org/r/20210113131634.3671-4-vbabka@suse.cz
Signed-off-by: Vlastimil Babka <vbabka@suse.cz>
Cc: Christoph Lameter <cl@linux.com>
Cc: David Hildenbrand <david@redhat.com>
Cc: David Rientjes <rientjes@google.com>
Cc: Joonsoo Kim <iamjoonsoo.kim@lge.com>
Cc: Michal Hocko <mhocko@kernel.org>
Cc: Pekka Enberg <penberg@kernel.org>
Cc: Qian Cai <cai@redhat.com>
Cc: Vladimir Davydov <vdavydov.dev@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Since commit 03afc0e25f ("slab: get_online_mems for
kmem_cache_{create,destroy,shrink}") we are taking memory hotplug lock for
SLAB and SLUB when creating, destroying or shrinking a cache. It is quite
a heavy lock and it's best to avoid it if possible, as we had several
issues with lockdep complaining about ordering in the past, see e.g.
e4f8e513c3 ("mm/slub: fix a deadlock in show_slab_objects()").
The problem scenario in 03afc0e25f (solved by the memory hotplug lock)
can be summarized as follows: while there's slab_mutex synchronizing new
kmem cache creation and SLUB's MEM_GOING_ONLINE callback
slab_mem_going_online_callback(), we may miss creation of kmem_cache_node
for the hotplugged node in the new kmem cache, because the hotplug
callback doesn't yet see the new cache, and cache creation in
init_kmem_cache_nodes() only inits kmem_cache_node for nodes in the
N_NORMAL_MEMORY nodemask, which however may not yet include the new node,
as that happens only later after the MEM_GOING_ONLINE callback.
Instead of using get/put_online_mems(), the problem can be solved by SLUB
maintaining its own nodemask of nodes for which it has allocated the
per-node kmem_cache_node structures. This nodemask would generally mirror
the N_NORMAL_MEMORY nodemask, but would be updated only in under SLUB's
control in its memory hotplug callbacks under the slab_mutex. This patch
adds such nodemask and its handling.
Commit 03afc0e25f mentiones "issues like [the one above]", but there
don't appear to be further issues. All the paths (shared for SLAB and
SLUB) taking the memory hotplug locks are also taking the slab_mutex,
except kmem_cache_shrink() where 03afc0e25f replaced slab_mutex with
get/put_online_mems().
We however cannot simply restore slab_mutex in kmem_cache_shrink(), as
SLUB can enters the function from a write to sysfs 'shrink' file, thus
holding kernfs lock, and in kmem_cache_create() the kernfs lock is nested
within slab_mutex. But on closer inspection we don't actually need to
protect kmem_cache_shrink() from hotplug callbacks: While SLUB's
__kmem_cache_shrink() does for_each_kmem_cache_node(), missing a new node
added in parallel hotplug is not fatal, and parallel hotremove does not
free kmem_cache_node's anymore after the previous patch, so use-after free
cannot happen. The per-node shrinking itself is protected by
n->list_lock. Same is true for SLAB, and SLOB is no-op.
SLAB also doesn't need the memory hotplug locking, which it only gained by
03afc0e25f through the shared paths in slab_common.c. Its memory
hotplug callbacks are also protected by slab_mutex against races with
these paths. The problem of SLUB relying on N_NORMAL_MEMORY doesn't apply
to SLAB, as its setup_kmem_cache_nodes relies on N_ONLINE, and the new
node is already set there during the MEM_GOING_ONLINE callback, so no
special care is needed for SLAB.
As such, this patch removes all get/put_online_mems() usage by the slab
subsystem.
Link: https://lkml.kernel.org/r/20210113131634.3671-3-vbabka@suse.cz
Signed-off-by: Vlastimil Babka <vbabka@suse.cz>
Cc: Christoph Lameter <cl@linux.com>
Cc: David Hildenbrand <david@redhat.com>
Cc: David Rientjes <rientjes@google.com>
Cc: Joonsoo Kim <iamjoonsoo.kim@lge.com>
Cc: Michal Hocko <mhocko@kernel.org>
Cc: Pekka Enberg <penberg@kernel.org>
Cc: Qian Cai <cai@redhat.com>
Cc: Vladimir Davydov <vdavydov.dev@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
There are kernel facilities such as per-CPU reference counts that give
error messages in generic handlers or callbacks, whose messages are
unenlightening. In the case of per-CPU reference-count underflow, this
is not a problem when creating a new use of this facility because in that
case the bug is almost certainly in the code implementing that new use.
However, trouble arises when deploying across many systems, which might
exercise corner cases that were not seen during development and testing.
Here, it would be really nice to get some kind of hint as to which of
several uses the underflow was caused by.
This commit therefore exposes a mem_dump_obj() function that takes
a pointer to memory (which must still be allocated if it has been
dynamically allocated) and prints available information on where that
memory came from. This pointer can reference the middle of the block as
well as the beginning of the block, as needed by things like RCU callback
functions and timer handlers that might not know where the beginning of
the memory block is. These functions and handlers can use mem_dump_obj()
to print out better hints as to where the problem might lie.
The information printed can depend on kernel configuration. For example,
the allocation return address can be printed only for slab and slub,
and even then only when the necessary debug has been enabled. For slab,
build with CONFIG_DEBUG_SLAB=y, and either use sizes with ample space
to the next power of two or use the SLAB_STORE_USER when creating the
kmem_cache structure. For slub, build with CONFIG_SLUB_DEBUG=y and
boot with slub_debug=U, or pass SLAB_STORE_USER to kmem_cache_create()
if more focused use is desired. Also for slub, use CONFIG_STACKTRACE
to enable printing of the allocation-time stack trace.
Cc: Christoph Lameter <cl@linux.com>
Cc: Pekka Enberg <penberg@kernel.org>
Cc: David Rientjes <rientjes@google.com>
Cc: Joonsoo Kim <iamjoonsoo.kim@lge.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: <linux-mm@kvack.org>
Reported-by: Andrii Nakryiko <andrii@kernel.org>
[ paulmck: Convert to printing and change names per Joonsoo Kim. ]
[ paulmck: Move slab definition per Stephen Rothwell and kbuild test robot. ]
[ paulmck: Handle CONFIG_MMU=n case where vmalloc() is kmalloc(). ]
[ paulmck: Apply Vlastimil Babka feedback on slab.c kmem_provenance(). ]
[ paulmck: Extract more info from !SLUB_DEBUG per Joonsoo Kim. ]
[ paulmck: Explicitly check for small pointers per Naresh Kamboju. ]
Acked-by: Joonsoo Kim <iamjoonsoo.kim@lge.com>
Acked-by: Vlastimil Babka <vbabka@suse.cz>
Tested-by: Naresh Kamboju <naresh.kamboju@linaro.org>
Signed-off-by: Paul E. McKenney <paulmck@kernel.org>
Instead of having two sets of kmem_caches: one for system-wide and
non-accounted allocations and the second one shared by all accounted
allocations, we can use just one.
The idea is simple: space for obj_cgroup metadata can be allocated on
demand and filled only for accounted allocations.
It allows to remove a bunch of code which is required to handle kmem_cache
clones for accounted allocations. There is no more need to create them,
accumulate statistics, propagate attributes, etc. It's a quite
significant simplification.
Also, because the total number of slab_caches is reduced almost twice (not
all kmem_caches have a memcg clone), some additional memory savings are
expected. On my devvm it additionally saves about 3.5% of slab memory.
[guro@fb.com: fix build on MIPS]
Link: http://lkml.kernel.org/r/20200717214810.3733082-1-guro@fb.com
Suggested-by: Johannes Weiner <hannes@cmpxchg.org>
Signed-off-by: Roman Gushchin <guro@fb.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Reviewed-by: Vlastimil Babka <vbabka@suse.cz>
Reviewed-by: Shakeel Butt <shakeelb@google.com>
Cc: Christoph Lameter <cl@linux.com>
Cc: Michal Hocko <mhocko@kernel.org>
Cc: Tejun Heo <tj@kernel.org>
Cc: Naresh Kamboju <naresh.kamboju@linaro.org>
Link: http://lkml.kernel.org/r/20200623174037.3951353-18-guro@fb.com
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Currently there are two lists of kmem_caches:
1) slab_caches, which contains all kmem_caches,
2) slab_root_caches, which contains only root kmem_caches.
And there is some preprocessor magic to have a single list if
CONFIG_MEMCG_KMEM isn't enabled.
It was required earlier because the number of non-root kmem_caches was
proportional to the number of memory cgroups and could reach really big
values. Now, when it cannot exceed the number of root kmem_caches, there
is really no reason to maintain two lists.
We never iterate over the slab_root_caches list on any hot paths, so it's
perfectly fine to iterate over slab_caches and filter out non-root
kmem_caches.
It allows to remove a lot of config-dependent code and two pointers from
the kmem_cache structure.
Signed-off-by: Roman Gushchin <guro@fb.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Reviewed-by: Vlastimil Babka <vbabka@suse.cz>
Reviewed-by: Shakeel Butt <shakeelb@google.com>
Cc: Christoph Lameter <cl@linux.com>
Cc: Johannes Weiner <hannes@cmpxchg.org>
Cc: Michal Hocko <mhocko@kernel.org>
Cc: Tejun Heo <tj@kernel.org>
Link: http://lkml.kernel.org/r/20200623174037.3951353-16-guro@fb.com
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Because the number of non-root kmem_caches doesn't depend on the number of
memory cgroups anymore and is generally not very big, there is no more
need for a dedicated workqueue.
Also, as there is no more need to pass any arguments to the
memcg_create_kmem_cache() except the root kmem_cache, it's possible to
just embed the work structure into the kmem_cache and avoid the dynamic
allocation of the work structure.
This will also simplify the synchronization: for each root kmem_cache
there is only one work. So there will be no more concurrent attempts to
create a non-root kmem_cache for a root kmem_cache: the second and all
following attempts to queue the work will fail.
On the kmem_cache destruction path there is no more need to call the
expensive flush_workqueue() and wait for all pending works to be finished.
Instead, cancel_work_sync() can be used to cancel/wait for only one work.
Signed-off-by: Roman Gushchin <guro@fb.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Reviewed-by: Vlastimil Babka <vbabka@suse.cz>
Reviewed-by: Shakeel Butt <shakeelb@google.com>
Cc: Christoph Lameter <cl@linux.com>
Cc: Johannes Weiner <hannes@cmpxchg.org>
Cc: Michal Hocko <mhocko@kernel.org>
Cc: Tejun Heo <tj@kernel.org>
Link: http://lkml.kernel.org/r/20200623174037.3951353-14-guro@fb.com
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This is fairly big but mostly red patch, which makes all accounted slab
allocations use a single set of kmem_caches instead of creating a separate
set for each memory cgroup.
Because the number of non-root kmem_caches is now capped by the number of
root kmem_caches, there is no need to shrink or destroy them prematurely.
They can be perfectly destroyed together with their root counterparts.
This allows to dramatically simplify the management of non-root
kmem_caches and delete a ton of code.
This patch performs the following changes:
1) introduces memcg_params.memcg_cache pointer to represent the
kmem_cache which will be used for all non-root allocations
2) reuses the existing memcg kmem_cache creation mechanism
to create memcg kmem_cache on the first allocation attempt
3) memcg kmem_caches are named <kmemcache_name>-memcg,
e.g. dentry-memcg
4) simplifies memcg_kmem_get_cache() to just return memcg kmem_cache
or schedule it's creation and return the root cache
5) removes almost all non-root kmem_cache management code
(separate refcounter, reparenting, shrinking, etc)
6) makes slab debugfs to display root_mem_cgroup css id and never
show :dead and :deact flags in the memcg_slabinfo attribute.
Following patches in the series will simplify the kmem_cache creation.
Signed-off-by: Roman Gushchin <guro@fb.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Reviewed-by: Vlastimil Babka <vbabka@suse.cz>
Reviewed-by: Shakeel Butt <shakeelb@google.com>
Cc: Christoph Lameter <cl@linux.com>
Cc: Johannes Weiner <hannes@cmpxchg.org>
Cc: Michal Hocko <mhocko@kernel.org>
Cc: Tejun Heo <tj@kernel.org>
Link: http://lkml.kernel.org/r/20200623174037.3951353-13-guro@fb.com
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Deprecate memory.kmem.slabinfo.
An empty file will be presented if corresponding config options are
enabled.
The interface is implementation dependent, isn't present in cgroup v2, and
is generally useful only for core mm debugging purposes. In other words,
it doesn't provide any value for the absolute majority of users.
A drgn-based replacement can be found in
tools/cgroup/memcg_slabinfo.py. It does support cgroup v1 and v2,
mimics memory.kmem.slabinfo output and also allows to get any
additional information without a need to recompile the kernel.
If a drgn-based solution is too slow for a task, a bpf-based tracing tool
can be used, which can easily keep track of all slab allocations belonging
to a memory cgroup.
Signed-off-by: Roman Gushchin <guro@fb.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Reviewed-by: Vlastimil Babka <vbabka@suse.cz>
Reviewed-by: Shakeel Butt <shakeelb@google.com>
Acked-by: Johannes Weiner <hannes@cmpxchg.org>
Cc: Christoph Lameter <cl@linux.com>
Cc: Michal Hocko <mhocko@kernel.org>
Cc: Tejun Heo <tj@kernel.org>
Link: http://lkml.kernel.org/r/20200623174037.3951353-11-guro@fb.com
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
In order to prepare for per-object slab memory accounting, convert
NR_SLAB_RECLAIMABLE and NR_SLAB_UNRECLAIMABLE vmstat items to bytes.
To make it obvious, rename them to NR_SLAB_RECLAIMABLE_B and
NR_SLAB_UNRECLAIMABLE_B (similar to NR_KERNEL_STACK_KB).
Internally global and per-node counters are stored in pages, however memcg
and lruvec counters are stored in bytes. This scheme may look weird, but
only for now. As soon as slab pages will be shared between multiple
cgroups, global and node counters will reflect the total number of slab
pages. However memcg and lruvec counters will be used for per-memcg slab
memory tracking, which will take separate kernel objects in the account.
Keeping global and node counters in pages helps to avoid additional
overhead.
The size of slab memory shouldn't exceed 4Gb on 32-bit machines, so it
will fit into atomic_long_t we use for vmstats.
Signed-off-by: Roman Gushchin <guro@fb.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Reviewed-by: Shakeel Butt <shakeelb@google.com>
Acked-by: Johannes Weiner <hannes@cmpxchg.org>
Acked-by: Vlastimil Babka <vbabka@suse.cz>
Cc: Christoph Lameter <cl@linux.com>
Cc: Michal Hocko <mhocko@kernel.org>
Cc: Tejun Heo <tj@kernel.org>
Link: http://lkml.kernel.org/r/20200623174037.3951353-4-guro@fb.com
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
As said by Linus:
A symmetric naming is only helpful if it implies symmetries in use.
Otherwise it's actively misleading.
In "kzalloc()", the z is meaningful and an important part of what the
caller wants.
In "kzfree()", the z is actively detrimental, because maybe in the
future we really _might_ want to use that "memfill(0xdeadbeef)" or
something. The "zero" part of the interface isn't even _relevant_.
The main reason that kzfree() exists is to clear sensitive information
that should not be leaked to other future users of the same memory
objects.
Rename kzfree() to kfree_sensitive() to follow the example of the recently
added kvfree_sensitive() and make the intention of the API more explicit.
In addition, memzero_explicit() is used to clear the memory to make sure
that it won't get optimized away by the compiler.
The renaming is done by using the command sequence:
git grep -w --name-only kzfree |\
xargs sed -i 's/kzfree/kfree_sensitive/'
followed by some editing of the kfree_sensitive() kerneldoc and adding
a kzfree backward compatibility macro in slab.h.
[akpm@linux-foundation.org: fs/crypto/inline_crypt.c needs linux/slab.h]
[akpm@linux-foundation.org: fix fs/crypto/inline_crypt.c some more]
Suggested-by: Joe Perches <joe@perches.com>
Signed-off-by: Waiman Long <longman@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Acked-by: David Howells <dhowells@redhat.com>
Acked-by: Michal Hocko <mhocko@suse.com>
Acked-by: Johannes Weiner <hannes@cmpxchg.org>
Cc: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Cc: James Morris <jmorris@namei.org>
Cc: "Serge E. Hallyn" <serge@hallyn.com>
Cc: Joe Perches <joe@perches.com>
Cc: Matthew Wilcox <willy@infradead.org>
Cc: David Rientjes <rientjes@google.com>
Cc: Dan Carpenter <dan.carpenter@oracle.com>
Cc: "Jason A . Donenfeld" <Jason@zx2c4.com>
Link: http://lkml.kernel.org/r/20200616154311.12314-3-longman@redhat.com
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
If the kmem_cache refcount is greater than one, we should not mark the
root kmem_cache as dying. If we mark the root kmem_cache dying
incorrectly, the non-root kmem_cache can never be destroyed. It
resulted in memory leak when memcg was destroyed. We can use the
following steps to reproduce.
1) Use kmem_cache_create() to create a new kmem_cache named A.
2) Coincidentally, the kmem_cache A is an alias for kmem_cache B,
so the refcount of B is just increased.
3) Use kmem_cache_destroy() to destroy the kmem_cache A, just
decrease the B's refcount but mark the B as dying.
4) Create a new memory cgroup and alloc memory from the kmem_cache
B. It leads to create a non-root kmem_cache for allocating memory.
5) When destroy the memory cgroup created in the step 4), the
non-root kmem_cache can never be destroyed.
If we repeat steps 4) and 5), this will cause a lot of memory leak. So
only when refcount reach zero, we mark the root kmem_cache as dying.
Fixes: 92ee383f6d ("mm: fix race between kmem_cache destroy, create and deactivate")
Signed-off-by: Muchun Song <songmuchun@bytedance.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Reviewed-by: Shakeel Butt <shakeelb@google.com>
Acked-by: Roman Gushchin <guro@fb.com>
Cc: Vlastimil Babka <vbabka@suse.cz>
Cc: Christoph Lameter <cl@linux.com>
Cc: Pekka Enberg <penberg@kernel.org>
Cc: David Rientjes <rientjes@google.com>
Cc: Joonsoo Kim <iamjoonsoo.kim@lge.com>
Cc: Shakeel Butt <shakeelb@google.com>
Cc: <stable@vger.kernel.org>
Link: http://lkml.kernel.org/r/20200716165103.83462-1-songmuchun@bytedance.com
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Now that "struct proc_ops" exist we can start putting there stuff which
could not fly with VFS "struct file_operations"...
Most of fs/proc/inode.c file is dedicated to make open/read/.../close
reliable in the event of disappearing /proc entries which usually happens
if module is getting removed. Files like /proc/cpuinfo which never
disappear simply do not need such protection.
Save 2 atomic ops, 1 allocation, 1 free per open/read/close sequence for such
"permanent" files.
Enable "permanent" flag for
/proc/cpuinfo
/proc/kmsg
/proc/modules
/proc/slabinfo
/proc/stat
/proc/sysvipc/*
/proc/swaps
More will come once I figure out foolproof way to prevent out module
authors from marking their stuff "permanent" for performance reasons
when it is not.
This should help with scalability: benchmark is "read /proc/cpuinfo R times
by N threads scattered over the system".
N R t, s (before) t, s (after)
-----------------------------------------------------
64 4096 1.582458 1.530502 -3.2%
256 4096 6.371926 6.125168 -3.9%
1024 4096 25.64888 24.47528 -4.6%
Benchmark source:
#include <chrono>
#include <iostream>
#include <thread>
#include <vector>
#include <sys/types.h>
#include <sys/stat.h>
#include <fcntl.h>
#include <unistd.h>
const int NR_CPUS = sysconf(_SC_NPROCESSORS_ONLN);
int N;
const char *filename;
int R;
int xxx = 0;
int glue(int n)
{
cpu_set_t m;
CPU_ZERO(&m);
CPU_SET(n, &m);
return sched_setaffinity(0, sizeof(cpu_set_t), &m);
}
void f(int n)
{
glue(n % NR_CPUS);
while (*(volatile int *)&xxx == 0) {
}
for (int i = 0; i < R; i++) {
int fd = open(filename, O_RDONLY);
char buf[4096];
ssize_t rv = read(fd, buf, sizeof(buf));
asm volatile ("" :: "g" (rv));
close(fd);
}
}
int main(int argc, char *argv[])
{
if (argc < 4) {
std::cerr << "usage: " << argv[0] << ' ' << "N /proc/filename R
";
return 1;
}
N = atoi(argv[1]);
filename = argv[2];
R = atoi(argv[3]);
for (int i = 0; i < NR_CPUS; i++) {
if (glue(i) == 0)
break;
}
std::vector<std::thread> T;
T.reserve(N);
for (int i = 0; i < N; i++) {
T.emplace_back(f, i);
}
auto t0 = std::chrono::system_clock::now();
{
*(volatile int *)&xxx = 1;
for (auto& t: T) {
t.join();
}
}
auto t1 = std::chrono::system_clock::now();
std::chrono::duration<double> dt = t1 - t0;
std::cout << dt.count() << '
';
return 0;
}
P.S.:
Explicit randomization marker is added because adding non-function pointer
will silently disable structure layout randomization.
[akpm@linux-foundation.org: coding style fixes]
Reported-by: kbuild test robot <lkp@intel.com>
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Cc: Joe Perches <joe@perches.com>
Link: http://lkml.kernel.org/r/20200222201539.GA22576@avx2
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
When I manually set default n to MEMCG_KMEM in init/Kconfig, bellow error
occurs,
mm/slab_common.c: In function 'memcg_slab_start':
mm/slab_common.c:1530:30: error: 'struct mem_cgroup' has no member named
'kmem_caches'
return seq_list_start(&memcg->kmem_caches, *pos);
^
mm/slab_common.c: In function 'memcg_slab_next':
mm/slab_common.c:1537:32: error: 'struct mem_cgroup' has no member named
'kmem_caches'
return seq_list_next(p, &memcg->kmem_caches, pos);
^
mm/slab_common.c: In function 'memcg_slab_show':
mm/slab_common.c:1551:16: error: 'struct mem_cgroup' has no member named
'kmem_caches'
if (p == memcg->kmem_caches.next)
^
CC arch/x86/xen/smp.o
mm/slab_common.c: In function 'memcg_slab_start':
mm/slab_common.c:1531:1: warning: control reaches end of non-void function
[-Wreturn-type]
}
^
mm/slab_common.c: In function 'memcg_slab_next':
mm/slab_common.c:1538:1: warning: control reaches end of non-void function
[-Wreturn-type]
}
^
That's because kmem_caches is defined only when CONFIG_MEMCG_KMEM is set,
while memcg_slab_start() will use it no matter CONFIG_MEMCG_KMEM is defined
or not.
By the way, the reason I mannuly undefined CONFIG_MEMCG_KMEM is to verify
whether my some other code change is still stable when CONFIG_MEMCG_KMEM is
not set. Unfortunately, the existing code has been already unstable since
v4.11.
Fixes: bc2791f857 ("slab: link memcg kmem_caches on their associated memory cgroup")
Signed-off-by: Yafang Shao <laoar.shao@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Acked-by: Andrew Morton <akpm@linux-foundation.org>
Cc: Tejun Heo <tj@kernel.org>
Cc: Vladimir Davydov <vdavydov.dev@gmail.com>
Cc: Johannes Weiner <hannes@cmpxchg.org>
Cc: Michal Hocko <mhocko@kernel.org>
Link: http://lkml.kernel.org/r/1580970260-2045-1-git-send-email-laoar.shao@gmail.com
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
