[ Upstream commit ddde5412fdaa5048bbca31529d46cb8da882870c ]
The upper 32-bit PHC register is not latched when reading the lower
32-bit PHC register. Current code leaves a small window where we may
not read correct higher order bits if the lower order bits are just about
to wrap around.
This patch fixes this by reading higher order bits twice and makes
sure that final value is correctly paired with its lower 32 bits.
Fixes: 30e96f487f ("bnxt_en: Do not read the PTP PHC during chip reset")
Cc: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: Pavan Chebbi <pavan.chebbi@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 4279414bff8af9898e8c53ae6c5bc17f68ad67b7 ]
bnxt_reinit_after_abort() is called during ifup when a previous
FW reset sequence has aborted or a previous ifup has failed after
detecting FW reset. In all cases, it is safe to assume that a
previous FW reset has completed and the driver may not have fully
reinitialized.
Prior to this patch, it is assumed that the
FUNC_DRV_IF_CHANGE_RESP_FLAGS_HOT_FW_RESET_DONE flag will always be
set by the firmware in bnxt_hwrm_if_change(). This may not be true if
the driver has already attempted to register with the firmware. The
firmware may not set the RESET_DONE flag again after the driver has
registered, assuming that the driver has seen the flag already.
Fix it to always go through the FW reset initialization path if
the BNXT_STATE_FW_RESET_DET flag is set. This flag is always set
by the driver after successfully going through bnxt_reinit_after_abort().
Fixes: 6882c36cf8 ("bnxt_en: attempt to reinitialize after aborted reset")
Reviewed-by: Pavan Chebbi <pavan.chebbi@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 9dec850fd7c210a04b4707df8e6c95bfafdd6a4b ]
GCC 12 currently generates a rather inconsistent warning:
drivers/net/ethernet/broadcom/tg3.c:17795:51: warning: array subscript 5 is above array bounds of ‘struct tg3_napi[5]’ [-Warray-bounds]
17795 | struct tg3_napi *tnapi = &tp->napi[i];
| ~~~~~~~~^~~
i is guaranteed < tp->irq_max which in turn is either 1 or 5.
There are more loops like this one in the driver, but strangely
GCC 12 dislikes only this single one.
Silence this silliness for now.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 6b77c06655b8a749c1a3d9ebc51e9717003f7e5a ]
The interrupt controller supplying the Wake-on-LAN interrupt line maybe
modular on some platforms (irq-bcm7038-l1.c) and might be probed at a
later time than the GENET driver. We need to specifically check for
-EPROBE_DEFER and propagate that error to ensure that we eventually
fetch the interrupt descriptor.
Fixes: 9deb48b53e7f ("bcmgenet: add WOL IRQ check")
Fixes: 5b1f0e6294 ("net: bcmgenet: Avoid touching non-existent interrupt")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Stefan Wahren <stefan.wahren@i2se.com>
Link: https://lore.kernel.org/r/20220511031752.2245566-1-f.fainelli@gmail.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 195af57914d15229186658ed26dab24b9ada4122 upstream.
In bnxt_poll_p5(), we first check cpr->has_more_work. If it is true,
we are in NAPI polling mode and we will call __bnxt_poll_cqs() to
continue polling. It is possible to exhanust the budget again when
__bnxt_poll_cqs() returns.
We then enter the main while loop to check for new entries in the NQ.
If we had previously exhausted the NAPI budget, we may call
__bnxt_poll_work() to process an RX entry with zero budget. This will
cause packets to be dropped unnecessarily, thinking that we are in the
netpoll path. Fix it by breaking out of the while loop if we need
to process an RX NQ entry with no budget left. We will then exit
NAPI and stay in polling mode.
Fixes: 389a877a3b ("bnxt_en: Process the NQ under NAPI continuous polling.")
Reviewed-by: Andy Gospodarek <andrew.gospodarek@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 13ba794397e45e52893cfc21d7a69cb5f341b407 upstream.
bnxt_open() can fail in this code path, especially on a VF when
it fails to reserve default rings:
bnxt_open()
__bnxt_open_nic()
bnxt_clear_int_mode()
bnxt_init_dflt_ring_mode()
RX rings would be set to 0 when we hit this error path.
It is possible for a subsequent bnxt_open() call to potentially succeed
with a code path like this:
bnxt_open()
bnxt_hwrm_if_change()
bnxt_fw_init_one()
bnxt_fw_init_one_p3()
bnxt_set_dflt_rfs()
bnxt_rfs_capable()
bnxt_hwrm_reserve_rings()
On older chips, RFS is capable if we can reserve the number of vnics that
is equal to RX rings + 1. But since RX rings is still set to 0 in this
code path, we may mistakenly think that RFS is supported for 0 RX rings.
Later, when the default RX rings are reserved and we try to enable
RFS, it would fail and cause bnxt_open() to fail unnecessarily.
We fix this in 2 places. bnxt_rfs_capable() will always return false if
RX rings is not yet set. bnxt_init_dflt_ring_mode() will call
bnxt_set_dflt_rfs() which will always clear the RFS flags if RFS is not
supported.
Fixes: 20d7d1c5c9 ("bnxt_en: reliably allocate IRQ table on reset to avoid crash")
Signed-off-by: Somnath Kotur <somnath.kotur@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit acac0541d1d65e81e599ec399d34d184d2424401 ]
The hardware checksum offloading requires use of a transmit
status block inserted before the outgoing frame data, this was
updated in '9a9ba2a4aaaa ("net: bcmgenet: always enable status blocks")'
However, skb_tx_timestamp() assumes that it is passed a raw frame
and PTP parsing chokes on this status block.
Fix this by calling __skb_pull(), which hides the TSB before calling
skb_tx_timestamp(), so an outgoing PTP packet is parsed correctly.
As the data in the skb has already been set up for DMA, and the
dma_unmap_* calls use a separately stored address, there is no
no effective change in the data transmission.
Signed-off-by: Jonathan Lemon <jonathan.lemon@gmail.com>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Link: https://lore.kernel.org/r/20220424165307.591145-1-jonathan.lemon@gmail.com
Fixes: d03825fba4 ("net: bcmgenet: add skb_tx_timestamp call")
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 27d4073f8d9af0340362554414f4961643a4f4de ]
Add checks in the XDP redirect callback to prevent XDP from running when
the TX ring is undergoing shutdown.
Also remove redundant checks in the XDP redirect callback to validate the
txr and the flag that indicates the ring supports XDP. The modulo
arithmetic on 'tx_nr_rings_xdp' already guarantees the derived TX
ring is an XDP ring. txr is also guaranteed to be valid after checking
BNXT_STATE_OPEN and within RCU grace period.
Fixes: f18c2b77b2 ("bnxt_en: optimized XDP_REDIRECT support")
Reviewed-by: Vladimir Olovyannikov <vladimir.olovyannikov@broadcom.com>
Signed-off-by: Ray Jui <ray.jui@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit facc173cf700e55b2ad249ecbd3a7537f7315691 ]
Insufficient space was being reserved in the page used for packet
reception, so the interface MTU could be set too large to still have
room for the contents of the packet when doing XDP redirect. This
resulted in the following message when redirecting a packet between
3520 and 3822 bytes with an MTU of 3822:
[311815.561880] XDP_WARN: xdp_update_frame_from_buff(line:200): Driver BUG: missing reserved tailroom
Fixes: f18c2b77b2 ("bnxt_en: optimized XDP_REDIRECT support")
Reviewed-by: Somnath Kotur <somnath.kotur@broadcom.com>
Reviewed-by: Pavan Chebbi <pavan.chebbi@broadcom.com>
Signed-off-by: Andy Gospodarek <gospo@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 4f81def272de17dc4bbd89ac38f49b2676c9b3d2 ]
If there are more CPUs than the number of TX XDP rings, multiple XDP
redirects can select the same TX ring based on the CPU on which
XDP redirect is called. Add locking when needed and use static
key to decide whether to take the lock.
Fixes: f18c2b77b2 ("bnxt_en: optimized XDP_REDIRECT support")
Signed-off-by: Pavan Chebbi <pavan.chebbi@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 7c492a2530c1f05441da541307c2534230dfd59b ]
If the flow control settings have been changed, a subsequent FW reset
may cause the ethernet link to toggle unnecessarily. This link toggle
will increase the down time by a few seconds.
The problem is caused by bnxt_update_phy_setting() detecting a false
mismatch in the flow control settings between the stored software
settings and the current FW settings after the FW reset. This mismatch
is caused by the AUTONEG bit added to link_info->req_flow_ctrl in an
inconsistent way in bnxt_set_pauseparam() in autoneg mode. The AUTONEG
bit should not be added to link_info->req_flow_ctrl.
Reviewed-by: Colin Winegarden <colin.winegarden@broadcom.com>
Reviewed-by: Pavan Chebbi <pavan.chebbi@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 8d3ea3d402db94b61075617e71b67459a714a502 ]
GCC12 appears to be much smarter about its dependency tracking and is
aware that the relaxed variants are just normal loads and stores and
this is causing problems like:
[ 210.074549] ------------[ cut here ]------------
[ 210.079223] NETDEV WATCHDOG: enabcm6e4ei0 (bcmgenet): transmit queue 1 timed out
[ 210.086717] WARNING: CPU: 1 PID: 0 at net/sched/sch_generic.c:529 dev_watchdog+0x234/0x240
[ 210.095044] Modules linked in: genet(E) nft_fib_inet nft_fib_ipv4 nft_fib_ipv6 nft_fib nft_reject_inet nf_reject_ipv4 nf_reject_ipv6 nft_reject nft_ct nft_chain_nat]
[ 210.146561] ACPI CPPC: PCC check channel failed for ss: 0. ret=-110
[ 210.146927] CPU: 1 PID: 0 Comm: swapper/1 Tainted: G E 5.17.0-rc7G12+ #58
[ 210.153226] CPPC Cpufreq:cppc_scale_freq_workfn: failed to read perf counters
[ 210.161349] Hardware name: Raspberry Pi Foundation Raspberry Pi 4 Model B/Raspberry Pi 4 Model B, BIOS EDK2-DEV 02/08/2022
[ 210.161353] pstate: 80400005 (Nzcv daif +PAN -UAO -TCO -DIT -SSBS BTYPE=--)
[ 210.161358] pc : dev_watchdog+0x234/0x240
[ 210.161364] lr : dev_watchdog+0x234/0x240
[ 210.161368] sp : ffff8000080a3a40
[ 210.161370] x29: ffff8000080a3a40 x28: ffffcd425af87000 x27: ffff8000080a3b20
[ 210.205150] x26: ffffcd425aa00000 x25: 0000000000000001 x24: ffffcd425af8ec08
[ 210.212321] x23: 0000000000000100 x22: ffffcd425af87000 x21: ffff55b142688000
[ 210.219491] x20: 0000000000000001 x19: ffff55b1426884c8 x18: ffffffffffffffff
[ 210.226661] x17: 64656d6974203120 x16: 0000000000000001 x15: 6d736e617274203a
[ 210.233831] x14: 2974656e65676d63 x13: ffffcd4259c300d8 x12: ffffcd425b07d5f0
[ 210.241001] x11: 00000000ffffffff x10: ffffcd425b07d5f0 x9 : ffffcd4258bdad9c
[ 210.248171] x8 : 00000000ffffdfff x7 : 000000000000003f x6 : 0000000000000000
[ 210.255341] x5 : 0000000000000000 x4 : 0000000000000000 x3 : 0000000000001000
[ 210.262511] x2 : 0000000000001000 x1 : 0000000000000005 x0 : 0000000000000044
[ 210.269682] Call trace:
[ 210.272133] dev_watchdog+0x234/0x240
[ 210.275811] call_timer_fn+0x3c/0x15c
[ 210.279489] __run_timers.part.0+0x288/0x310
[ 210.283777] run_timer_softirq+0x48/0x80
[ 210.287716] __do_softirq+0x128/0x360
[ 210.291392] __irq_exit_rcu+0x138/0x140
[ 210.295243] irq_exit_rcu+0x1c/0x30
[ 210.298745] el1_interrupt+0x38/0x54
[ 210.302334] el1h_64_irq_handler+0x18/0x24
[ 210.306445] el1h_64_irq+0x7c/0x80
[ 210.309857] arch_cpu_idle+0x18/0x2c
[ 210.313445] default_idle_call+0x4c/0x140
[ 210.317470] cpuidle_idle_call+0x14c/0x1a0
[ 210.321584] do_idle+0xb0/0x100
[ 210.324737] cpu_startup_entry+0x30/0x8c
[ 210.328675] secondary_start_kernel+0xe4/0x110
[ 210.333138] __secondary_switched+0x94/0x98
The assumption when these were relaxed seems to be that device memory
would be mapped non reordering, and that other constructs
(spinlocks/etc) would provide the barriers to assure that packet data
and in memory rings/queues were ordered with respect to device
register reads/writes. This itself seems a bit sketchy, but the real
problem with GCC12 is that it is moving the actual reads/writes around
at will as though they were independent operations when in truth they
are not, but the compiler can't know that. When looking at the
assembly dumps for many of these routines its possible to see very
clean, but not strictly in program order operations occurring as the
compiler would be free to do if these weren't actually register
reads/write operations.
Its possible to suppress the timeout with a liberal bit of dma_mb()'s
sprinkled around but the device still seems unable to reliably
send/receive data. A better plan is to use the safer readl/writel
everywhere.
Since this partially reverts an older commit, which notes the use of
the relaxed variants for performance reasons. I would suggest that
any performance problems with this commit are targeted at relaxing only
the performance critical code paths after assuring proper barriers.
Fixes: 69d2ea9c79 ("net: bcmgenet: Use correct I/O accessors")
Reported-by: Peter Robinson <pbrobinson@gmail.com>
Signed-off-by: Jeremy Linton <jeremy.linton@arm.com>
Acked-by: Peter Robinson <pbrobinson@gmail.com>
Tested-by: Peter Robinson <pbrobinson@gmail.com>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Link: https://lore.kernel.org/r/20220310045358.224350-1-jeremy.linton@arm.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit dcf500065fabe27676dfe7b4ba521a4f1e0fc8ac upstream.
The Broadcom bnxt_ptp driver does not compile with GCC 11.2.2 when
CONFIG_WERROR is enabled. The following error is generated:
drivers/net/ethernet/broadcom/bnxt/bnxt_ptp.c: In function ‘bnxt_ptp_enable’:
drivers/net/ethernet/broadcom/bnxt/bnxt_ptp.c:400:43: error: array
subscript 255 is above array bounds of ‘struct pps_pin[4]’
[-Werror=array-bounds]
400 | ptp->pps_info.pins[pin_id].event = BNXT_PPS_EVENT_EXTERNAL;
| ~~~~~~~~~~~~~~~~~~^~~~~~~~
In file included from drivers/net/ethernet/broadcom/bnxt/bnxt_ptp.c:20:
drivers/net/ethernet/broadcom/bnxt/bnxt_ptp.h:75:24: note: while
referencing ‘pins’
75 | struct pps_pin pins[BNXT_MAX_TSIO_PINS];
| ^~~~
cc1: all warnings being treated as errors
This is due to the function ptp_find_pin() returning a pin ID of -1 when
a valid pin is not found and this error never being checked.
Change the TSIO_PIN_VALID() function to also check that a pin ID is not
negative and use this macro in bnxt_ptp_enable() to check the result of
the calls to ptp_find_pin() to return an error early for invalid pins.
This fixes the compilation error.
Cc: <stable@vger.kernel.org>
Fixes: 9e518f2580 ("bnxt_en: 1PPS functions to configure TSIO pins")
Signed-off-by: Damien Le Moal <damien.lemoal@opensource.wdc.com>
Reviewed-by: Michael Chan <michael.chan@broadcom.com>
Link: https://lore.kernel.org/r/20220328062708.207079-1-damien.lemoal@opensource.wdc.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 0f643c88c8d240eba0ea25c2e095a46515ff46e9 ]
The RXCHK block will return a partial checksum of 0 if it encounters
a problem while receiving a packet. Since a 1's complement sum can
only produce this result if no bits are set in the received data
stream it is fair to treat it as an invalid partial checksum and
not pass it up the stack.
Fixes: 8101553978 ("net: bcmgenet: use CHECKSUM_COMPLETE for NETIF_F_RXCSUM")
Signed-off-by: Doug Berger <opendmb@gmail.com>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Link: https://lore.kernel.org/r/20220317012812.1313196-1-opendmb@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 424e7834e293936a54fcf05173f2884171adc5a3 ]
Commit b7a49f73059f ("bnx2x: Utilize firmware 7.13.21.0")
added request_firmware() logic in probe() which caused
load failure when firmware file is not present in initrd (below),
as access to firmware file is not feasible during probe.
Direct firmware load for bnx2x/bnx2x-e2-7.13.15.0.fw failed with error -2
Direct firmware load for bnx2x/bnx2x-e2-7.13.21.0.fw failed with error -2
This patch fixes this issue by -
1. Removing request_firmware() logic from the probe()
such that .ndo_open() handle it as it used to handle
it earlier
2. Given request_firmware() is removed from probe(), so
driver has to relax FW version comparisons a bit against
the already loaded FW version (by some other PFs of same
adapter) to allow different compatible/close enough FWs with which
multiple PFs may run with (in different environments), as the
given PF who is in probe flow has no idea now with which firmware
file version it is going to initialize the device in ndo_open()
Link: https://lore.kernel.org/all/46f2d9d9-ae7f-b332-ddeb-b59802be2bab@molgen.mpg.de/
Reported-by: Paul Menzel <pmenzel@molgen.mpg.de>
Tested-by: Paul Menzel <pmenzel@molgen.mpg.de>
Fixes: b7a49f73059f ("bnx2x: Utilize firmware 7.13.21.0")
Signed-off-by: Manish Chopra <manishc@marvell.com>
Signed-off-by: Ariel Elior <aelior@marvell.com>
Link: https://lore.kernel.org/r/20220316214613.6884-1-manishc@marvell.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 8ccffe9ac3239e549beaa0a9d5e1a1eac94e866c ]
Fix an error message and report the correct failing function.
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 00b022f8f876a3a036b0df7f971001bef6398605 ]
Some of the bcmgenet platforms don't correctly support WOL, yet
ethtool returns:
"Supports Wake-on: gsf"
which is false.
Ideally if there isn't a wol_irq, or there is something else that
keeps the device from being able to wakeup it should display:
"Supports Wake-on: d"
This patch checks whether the device can wakup, before using the
hard-coded supported flags. This corrects the ethtool reporting, as
well as the WOL configuration because ethtool verifies that the mode
is supported before attempting it.
Fixes: c51de7f397 ("net: bcmgenet: add Wake-on-LAN support code")
Signed-off-by: Jeremy Linton <jeremy.linton@arm.com>
Tested-by: Peter Robinson <pbrobinson@gmail.com>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Link: https://lore.kernel.org/r/20220310045535.224450-1-jeremy.linton@arm.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit cfcab3b3b61584a02bb523ffa99564eafa761dfe ]
In the current code, we setup the port to PHY or MAC loopback mode
and then transmit a test broadcast packet for the loopback test. This
scheme fails sometime if the port is shared with management firmware
that can also send packets. The driver may receive the management
firmware's packet and the test will fail when the contents don't
match the test packet.
Change the test packet to use it's own MAC address as the destination
and setup the port to only receive it's own MAC address. This should
filter out other packets sent by management firmware.
Fixes: 91725d89b9 ("bnxt_en: Add PHY loopback to ethtool self-test.")
Reviewed-by: Pavan Chebbi <pavan.chebbi@broadcom.com>
Reviewed-by: Edwin Peer <edwin.peer@broadcom.com>
Reviewed-by: Andy Gospodarek <gospo@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b891106da52b2c12dbaf73400f6d225b06a38d80 ]
When polling for the firmware message response, we first poll for the
response message header. Once the valid length is detected in the
header, we poll for the valid bit at the end of the message which
signals DMA completion. Normally, this poll time for DMA completion
is extremely short (0 to a few usec). But on some devices under some
rare conditions, it can be up to about 20 msec.
Increase this delay to 50 msec and use udelay() for the first 10 usec
for the common case, and usleep_range() beyond that.
Also, change the error message to include the above delay time when
printing the timeout value.
Fixes: 3c8c20db76 ("bnxt_en: move HWRM API implementation into separate file")
Reviewed-by: Vladimir Olovyannikov <vladimir.olovyannikov@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 8cdb15924252e27af16c4a8fe0fc606ce5fd04dc upstream.
We should setup multicast only when net_device flags explicitly
has IFF_MULTICAST set. Otherwise we will incorrectly turn it on
even when not asked. Fix it by only passing the multicast table
to the firmware if IFF_MULTICAST is set.
Fixes: 7d2837dd7a ("bnxt_en: Setup multicast properly after resetting device.")
Signed-off-by: Pavan Chebbi <pavan.chebbi@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 6758f937669dba14c6aac7ca004edda42ec1b18d upstream.
For offline (destructive) self tests, we need to stop the RDMA driver
first. Otherwise, the RDMA driver will run into unrecoverable errors
when destructive firmware tests are being performed.
The irq_re_init parameter used in the half close and half open
sequence when preparing the NIC for offline tests should be set to
true because the RDMA driver will free all IRQs before the offline
tests begin.
Fixes: 55fd0cf320 ("bnxt_en: Add external loopback test to ethtool selftest.")
Reviewed-by: Edwin Peer <edwin.peer@broadcom.com>
Reviewed-by: Ben Li <ben.li@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 84d3c83e6ea7d46cf3de3a54578af73eb24a64f2 upstream.
ethtool --show-fec <interface> does not show anything when the Active
FEC setting in the chip is set to None. Fix it to properly return
ETHTOOL_FEC_OFF in that case.
Fixes: 8b2775890a ("bnxt_en: Report FEC settings to ethtool.")
Signed-off-by: Somnath Kotur <somnath.kotur@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit e13ad1443684f7afaff24cf207e85e97885256bd upstream.
Commit b7a49f73059f ("bnx2x: Utilize firmware 7.13.21.0") added
new firmware support in the driver with maintaining older firmware
compatibility. However, older firmware was not added in MODULE_FIRMWARE()
which caused missing firmware files in initrd image leading to driver load
failure from initrd. This patch adds MODULE_FIRMWARE() for older firmware
version to have firmware files included in initrd.
Fixes: b7a49f73059f ("bnx2x: Utilize firmware 7.13.21.0")
Link: https://bugzilla.kernel.org/show_bug.cgi?id=215627
Signed-off-by: Manish Chopra <manishc@marvell.com>
Signed-off-by: Alok Prasad <palok@marvell.com>
Signed-off-by: Ariel Elior <aelior@marvell.com>
Link: https://lore.kernel.org/r/20220223085720.12021-1-manishc@marvell.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 6aba04ee3263669b335458c4cf4c7d97d6940229 upstream.
This reverts commit 3710e80952.
Since idm_base and nicpm_base are still optional resources not present
on all platforms, this breaks the driver for everything except Northstar
2 (which has both).
The same change was already reverted once with 755f5738ff ("net:
broadcom: fix a mistake about ioremap resource").
So let's do it again.
Fixes: 3710e80952 ("net: ethernet: bgmac: Use devm_platform_ioremap_resource_byname")
Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
[florian: Added comments to explain the resources are optional]
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://lore.kernel.org/r/20220216184634.2032460-1-f.fainelli@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 802d4d207e75d7208ff75adb712b556c1e91cf1c upstream
Commit 0a6890b9b4 ("bnx2x: Utilize FW 7.13.15.0.")
added validation for fastpath HSI versions for different
client init which was not meant for SR-IOV VF clients, which
resulted in firmware asserts when running VF clients with
different fastpath HSI version.
This patch along with the new firmware support in patch #1
fixes this behavior in order to not validate fastpath HSI
version for the VFs.
Fixes: 0a6890b9b4 ("bnx2x: Utilize FW 7.13.15.0.")
Signed-off-by: Manish Chopra <manishc@marvell.com>
Signed-off-by: Prabhakar Kushwaha <pkushwaha@marvell.com>
Signed-off-by: Alok Prasad <palok@marvell.com>
Signed-off-by: Ariel Elior <aelior@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit b7a49f73059fe6147b6b78e8f674ce0d21237432 upstream
This new firmware addresses few important issues and enhancements
as mentioned below -
- Support direct invalidation of FP HSI Ver per function ID, required for
invalidating FP HSI Ver prior to each VF start, as there is no VF start
- BRB hardware block parity error detection support for the driver
- Fix the FCOE underrun flow
- Fix PSOD during FCoE BFS over the NIC ports after preboot driver
- Maintains backward compatibility
This patch incorporates this new firmware 7.13.21.0 in bnx2x driver.
Signed-off-by: Manish Chopra <manishc@marvell.com>
Signed-off-by: Prabhakar Kushwaha <pkushwaha@marvell.com>
Signed-off-by: Alok Prasad <palok@marvell.com>
Signed-off-by: Ariel Elior <aelior@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 9deb48b53e7f4056c2eaa2dc2ee3338df619e4f6 upstream.
The driver neglects to check the result of platform_get_irq_optional()'s
call and blithely passes the negative error codes to devm_request_irq()
(which takes *unsigned* IRQ #), causing it to fail with -EINVAL.
Stop calling devm_request_irq() with the invalid IRQ #s.
Fixes: 8562056f26 ("net: bcmgenet: request Wake-on-LAN interrupt")
Signed-off-by: Sergey Shtylyov <s.shtylyov@omp.ru>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit bce9a0b7900836df223ab638090df0cb8430d9e8 ]
Some older devices cannot accommodate the 40 seconds timeout
cap for long running commands (such as NVRAM commands) due to
hardware limitations. Allow these devices to request more time for
these long running commands, but print a warning, since the longer
timeout may cause the hung task watchdog to trigger. In the case of a
firmware update operation, this is preferable to failing outright.
v2: Use bp->hwrm_cmd_max_timeout directly without the constants.
Fixes: 881d8353b0 ("bnxt_en: Add an upper bound for all firmware command timeouts.")
Signed-off-by: Edwin Peer <edwin.peer@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b032228e58ea2477955058ad4d70a636ce1dec51 ]
Change bnxt_get_coredump() and bnxt_get_coredump_length() to non-static
functions.
Signed-off-by: Edwin Peer <edwin.peer@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 9a575c8c25ae2372112db6d6b3e553cd90e9f02b ]
The coredump functionality will be used by devlink health. Refactor
these functions that get coredump and coredump length. There is no
functional change, but the following checkpatch warnings were
addressed:
- strscpy is preferred over strlcpy.
- sscanf results should be checked, with an additional warning.
Signed-off-by: Edwin Peer <edwin.peer@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 8b8e6e782456f1ce02a7ae914bbd5b1053f0b034 ]
The descriptor list is a shared resource across all of the transmit queues, and
the locking mechanism used today only protects concurrency across a given
transmit queue between the transmit and reclaiming. This creates an opportunity
for the SYSTEMPORT hardware to work on corrupted descriptors if we have
multiple producers at once which is the case when using multiple transmit
queues.
This was particularly noticeable when using multiple flows/transmit queues and
it showed up in interesting ways in that UDP packets would get a correct UDP
header checksum being calculated over an incorrect packet length. Similarly TCP
packets would get an equally correct checksum computed by the hardware over an
incorrect packet length.
The SYSTEMPORT hardware maintains an internal descriptor list that it re-arranges
when the driver produces a new descriptor anytime it writes to the
WRITE_PORT_{HI,LO} registers, there is however some delay in the hardware to
re-organize its descriptors and it is possible that concurrent TX queues
eventually break this internal allocation scheme to the point where the
length/status part of the descriptor gets used for an incorrect data buffer.
The fix is to impose a global serialization for all TX queues in the short
section where we are writing to the WRITE_PORT_{HI,LO} registers which solves
the corruption even with multiple concurrent TX queues being used.
Fixes: 80105befdb ("net: systemport: add Broadcom SYSTEMPORT Ethernet MAC driver")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Link: https://lore.kernel.org/r/20211215202450.4086240-1-f.fainelli@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 128f6ec95a282b2d8bc1041e59bf65810703fa44 upstream.
The return value of dma_set_coherent_mask() is not always 0.
To catch the exception in case that dma is not support the mask.
Fixes: 9d61d138ab ("net: broadcom: rename BCM4908 driver & update DT binding")
Signed-off-by: Jiasheng Jiang <jiasheng@iscas.ac.cn>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit b0757491a118ae5727cf9f1c3a11544397d46596 ]
The driver does not check if hw-tc-offload is enabled for the device
before offloading a flow in the context of indirect block callback.
Fix this by checking NETIF_F_HW_TC in the features flag and rejecting
the offload request. This will avoid unnecessary dmesg error logs when
hw-tc-offload is disabled, such as these:
bnxt_en 0000:19:00.1 eno2np1: dev(ifindex=294) not on same switch
bnxt_en 0000:19:00.1 eno2np1: Error: bnxt_tc_add_flow: cookie=0xffff8dace1c88000 error=-22
bnxt_en 0000:19:00.0 eno1np0: dev(ifindex=294) not on same switch
bnxt_en 0000:19:00.0 eno1np0: Error: bnxt_tc_add_flow: cookie=0xffff8dace1c88000 error=-22
Reported-by: Marcelo Ricardo Leitner <mleitner@redhat.com>
Fixes: 627c89d00f ("bnxt_en: flow_offload: offload tunnel decap rules via indirect callbacks")
Signed-off-by: Sriharsha Basavapatna <sriharsha.basavapatna@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f8885ac89ce310570e5391fe0bf0ec9c7c9b4fdc ]
Smatch says:
bnx2x_init_ops.h:640 bnx2x_ilt_client_mem_op()
warn: variable dereferenced before check 'ilt' (see line 638)
Move ilt_cli variable initialization _after_ ilt validation, because
it's unsafe to deref the pointer before validation check.
Fixes: 523224a3b3 ("bnx2x, cnic, bnx2i: use new FW/HSI")
Signed-off-by: Pavel Skripkin <paskripkin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e624c70e1131e145bd0510b8a700b5e2d112e377 ]
devlink is a software interface that doesn't depend on any hardware
capabilities. The failure in SW means memory issues, wrong parameters,
programmer error e.t.c.
Like any other such interface in the kernel, the returned status of
devlink APIs should be checked and propagated further and not ignored.
Fixes: 4ab0c6a8ff ("bnxt_en: add support to enable VF-representors")
Signed-off-by: Leon Romanovsky <leonro@nvidia.com>
Reviewed-by: Edwin Peer <edwin.peer@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
This patch is a replication of Christian Lamparter's "net: bgmac-bcma:
handle deferred probe error due to mac-address" patch for the
bgmac-platform driver [1].
As is the case with the bgmac-bcma driver, this change is to cover the
scenario where the MAC address cannot yet be discovered due to reliance
on an nvmem provider which is yet to be instantiated, resulting in a
random address being assigned that has to be manually overridden.
[1] https://lore.kernel.org/netdev/20210919115725.29064-1-chunkeey@gmail.com
Signed-off-by: Matthew Hagan <mnhagan88@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The smallest TX ring size we support must fit a TX SKB with MAX_SKB_FRAGS
+ 1. Because the first TX BD for a packet is always a long TX BD, we
need an extra TX BD to fit this packet. Define BNXT_MIN_TX_DESC_CNT with
this value to make this more clear. The current code uses a minimum
that is off by 1. Fix it using this constant.
The tx_wake_thresh to determine when to wake up the TX queue is half the
ring size but we must have at least BNXT_MIN_TX_DESC_CNT for the next
packet which may have maximum fragments. So the comparison of the
available TX BDs with tx_wake_thresh should be >= instead of > in the
current code. Otherwise, at the smallest ring size, we will never wake
up the TX queue and will cause TX timeout.
Fixes: c0c050c58d ("bnxt_en: New Broadcom ethernet driver.")
Reviewed-by: Pavan Chebbi <pavan.chebbi@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadocm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Due to the inclusion of nvmem handling into the mac-address getter
function of_get_mac_address() by
commit d01f449c00 ("of_net: add NVMEM support to of_get_mac_address")
it is now possible to get a -EPROBE_DEFER return code. Which did cause
bgmac to assign a random ethernet address.
This exact issue happened on my Meraki MR32. The nvmem provider is
an EEPROM (at24c64) which gets instantiated once the module
driver is loaded... This happens once the filesystem becomes available.
With this patch, bgmac_probe() will propagate the -EPROBE_DEFER error.
Then the driver subsystem will reschedule the probe at a later time.
Cc: Petr Štetiar <ynezz@true.cz>
Cc: Michael Walle <michael@walle.cc>
Fixes: d01f449c00 ("of_net: add NVMEM support to of_get_mac_address")
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove the assert from the callback priv lookup function since it does
not require RTNL lock and is already protected by flow_indr_block_lock.
This will avoid warnings from being emitted to dmesg if the driver
registers its callback after an ingress qdisc was created for a
netdevice.
The warnings started after the following patch was merged:
commit 74fc4f8287 ("net: Fix offloading indirect devices dependency on qdisc order creation")
Signed-off-by: Eli Cohen <elic@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We recently changed the completion ring page arrays to be dynamically
allocated to better support the expanded range of ring depths. The
cleanup path for this was not quite complete. It might cause the
shutdown path to crash if we need to abort before the completion ring
arrays have been allocated and initialized.
Fix it by initializing the ring_mem->pg_arr to NULL after freeing the
completion ring page array. Add a check in bnxt_free_ring() to skip
referencing the rmem->pg_arr if it is NULL.
Fixes: 03c7448790 ("bnxt_en: Don't use static arrays for completion ring pages")
Reviewed-by: Andy Gospodarek <gospo@broadcom.com>
Reviewed-by: Edwin Peer <edwin.peer@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The call to bnxt_free_mem(..., false) in the bnxt_half_open_nic() error
path will deallocate ring descriptor memory via bnxt_free_?x_rings(),
but because irq_re_init is false, the ring info itself is not freed.
To simplify error paths, deallocation functions have generally been
written to be safe when called on unallocated memory. It should always
be safe to call dev_close(), which calls bnxt_free_skbs() a second time,
even in this semi- allocated ring state.
Calling bnxt_free_skbs() a second time with the rings already freed will
cause NULL pointer dereference. Fix it by checking the rings are valid
before proceeding in bnxt_free_tx_skbs() and
bnxt_free_one_rx_ring_skbs().
Fixes: 975bc99a4a ("bnxt_en: Refactor bnxt_free_rx_skbs().")
Signed-off-by: Edwin Peer <edwin.peer@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The recent patch has introduced a regression by not reading the reset
count in the ERROR_RECOVERY async event handler. We may have just
gone through a reset and the reset count has just incremented. If
we don't update the reset count in the ERROR_RECOVERY event handler,
the health check timer will see that the reset count has changed and
will initiate an unintended reset.
Restore the unconditional update of the reset count in
bnxt_async_event_process() if error recovery watchdog is enabled.
Also, update the reset count at the end of the reset sequence to
make it even more robust.
Fixes: 1b2b918319 ("bnxt_en: Fix possible unintended driver initiated error recovery")
Reviewed-by: Edwin Peer <edwin.peer@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If error recovery is already enabled, bnxt_timer() will periodically
check the heartbeat register and the reset counter. If we get an
error recovery async. notification from the firmware (e.g. change in
primary/secondary role), we will immediately read and update the
heartbeat register and the reset counter. If the timer for the next
health check expires soon after this, we may read the heartbeat register
again in quick succession and find that it hasn't changed. This will
trigger error recovery unintentionally.
The likelihood is small because we also reset fw_health->tmr_counter
which will reset the interval for the next health check. But the
update is not protected and bnxt_timer() can miss the update and
perform the health check without waiting for the full interval.
Fix it by only reading the heartbeat register and reset counter in
bnxt_async_event_process() if error recovery is trasitioning to the
enabled state. Also add proper memory barriers so that when enabling
for the first time, bnxt_timer() will see the tmr_counter interval and
perform the health check after the full interval has elapsed.
Fixes: 7e914027f7 ("bnxt_en: Enable health monitoring.")
Reviewed-by: Edwin Peer <edwin.peer@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
