[ Upstream commit fed0d9f13266a22ce1fc9a97521ef9cdc6271a23 ]
Clear VF MAC from parent PF and remove VF filter from VSI when both
conditions are true:
-VIRTCHNL_VF_OFFLOAD_USO is not used
-VM MAC was not set from PF level
It affects older version of IAVF and it allow them to change MAC
Address on VM, newer IAVF won't change their behaviour.
Previously it wasn't possible to change VF's MAC Address on VM
because there is flag on IAVF driver that won't allow to
change MAC Address if this address is given from PF driver.
Fixes: 155f0ac2c9 ("iavf: allow permanent MAC address to change")
Signed-off-by: Norbert Zulinski <norbertx.zulinski@intel.com>
Signed-off-by: Jan Sokolowski <jan.sokolowski@intel.com>
Tested-by: Konrad Jankowski <konrad0.jankowski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 1adb1563e7b7ec659379a18e607e8bc3522d8a78 ]
Dropped packets caused by too large frames were not included in
dropped RX packets statistics.
Issue was caused by not reading the GL_RXERR1 register. That register
stores count of packet which was have been dropped due to too large
size.
Fix it by reading GL_RXERR1 register for each interface.
Repro steps:
Send a packet larger than the set MTU to SUT
Observe rx statists: ethtool -S <interface> | grep rx | grep -v ": 0"
Fixes: 41a9e55c89 ("i40e: add missing VSI statistics")
Signed-off-by: Lukasz Cieplicki <lukaszx.cieplicki@intel.com>
Signed-off-by: Jedrzej Jagielski <jedrzej.jagielski@intel.com>
Tested-by: Gurucharan <gurucharanx.g@intel.com> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 4e0effd9007ea0be31f7488611eb3824b4541554 ]
Intel I210 on some Intel Alder Lake platforms can only achieve ~750Mbps
Tx speed via iperf. The RR2DCDELAY shows around 0x2xxx DMA delay, which
will be significantly lower when 1) ASPM is disabled or 2) SoC package
c-state stays above PC3. When the RR2DCDELAY is around 0x1xxx the Tx
speed can reach to ~950Mbps.
According to the I210 datasheet "8.26.1 PCIe Misc. Register - PCIEMISC",
"DMA Idle Indication" doesn't seem to tie to DMA coalesce anymore, so
set it to 1b for "DMA is considered idle when there is no Rx or Tx AND
when there are no TLPs indicating that CPU is active detected on the
PCIe link (such as the host executes CSR or Configuration register read
or write operation)" and performing Tx should also fall under "active
CPU on PCIe link" case.
In addition to that, commit b6e0c419f0 ("igb: Move DMA Coalescing init
code to separate function.") seems to wrongly changed from enabling
E1000_PCIEMISC_LX_DECISION to disabling it, also fix that.
Fixes: b6e0c419f0 ("igb: Move DMA Coalescing init code to separate function.")
Signed-off-by: Kai-Heng Feng <kai.heng.feng@canonical.com>
Tested-by: Gurucharan <gurucharanx.g@intel.com> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Link: https://lore.kernel.org/r/20220621221056.604304-1-anthony.l.nguyen@intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c3d184c83ff4b80167e34edfc3d21df424bf27ff ]
In current implementation ice_update_phy_type enables all link modes
for selected speed. This approach doesn't work for 1000M speeds,
because both copper (1000baseT) and optical (1000baseX) standards
cannot be enabled at once.
Fix this, by adding the function `ice_set_phy_type_from_speed()`
for 1000M speeds.
Fixes: 48cb27f2fd ("ice: Implement handlers for ethtool PHY/link operations")
Signed-off-by: Anatolii Gerasymenko <anatolii.gerasymenko@intel.com>
Tested-by: Gurucharan <gurucharanx.g@intel.com> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit fd5855e6b1358e816710afee68a1d2bc685176ca ]
After PF reset and ethtool -t there was call trace in dmesg
sometimes leading to panic. When there was some time, around 5
seconds, between reset and test there were no errors.
Problem was that pf reset calls i40e_vsi_close in prep_for_reset
and ethtool -t calls i40e_vsi_close in diag_test. If there was not
enough time between those commands the second i40e_vsi_close starts
before previous i40e_vsi_close was done which leads to crash.
Add check to diag_test if pf is in reset and don't start offline
tests if it is true.
Add netif_info("testing failed") into unhappy path of i40e_diag_test()
Fixes: e17bc411ae ("i40e: Disable offline diagnostics if VFs are enabled")
Fixes: 510efb2682 ("i40e: Fix ethtool offline diagnostic with netqueues")
Signed-off-by: Michal Jaron <michalx.jaron@intel.com>
Signed-off-by: Aleksandr Loktionov <aleksandr.loktionov@intel.com>
Tested-by: Gurucharan <gurucharanx.g@intel.com> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 0bb050670ac90a167ecfa3f9590f92966c9a3677 ]
If ADQ is enabled for a VF, then actual number of queue pair
is a number of currently available traffic classes for this VF.
Without this change the configuration of the Rx/Tx queues
fails with error.
Fixes: d29e0d233e ("i40e: missing input validation on VF message handling by the PF")
Signed-off-by: Grzegorz Szczurek <grzegorzx.szczurek@intel.com>
Signed-off-by: Jedrzej Jagielski <jedrzej.jagielski@intel.com>
Tested-by: Bharathi Sreenivas <bharathi.sreenivas@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c3238d36c3a2be0a29a9d848d6c51e1b14be6692 ]
Procedure of configure tc flower filters erroneously allows to create
filters on TC0 where unfiltered packets are also directed by default.
Issue was caused by insufficient checks of hw_tc parameter specifying
the hardware traffic class to pass matching packets to.
Fix checking hw_tc parameter which blocks creation of filters on TC0.
Fixes: 2f4b411a3d ("i40e: Enable cloud filters via tc-flower")
Signed-off-by: Grzegorz Szczurek <grzegorzx.szczurek@intel.com>
Signed-off-by: Jedrzej Jagielski <jedrzej.jagielski@intel.com>
Tested-by: Bharathi Sreenivas <bharathi.sreenivas@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 7bb0fb7c63df95d6027dc50d6af3bc3bbbc25483 upstream.
When the promiscuous mode is enabled on a VF, the IXGBE_VMOLR_VPE
bit (VLAN Promiscuous Enable) is set. This means that the VF will
receive packets whose VLAN is not the same than the VLAN of the VF.
For instance, in this situation:
┌────────┐ ┌────────┐ ┌────────┐
│ │ │ │ │ │
│ │ │ │ │ │
│ VF0├────┤VF1 VF2├────┤VF3 │
│ │ │ │ │ │
└────────┘ └────────┘ └────────┘
VM1 VM2 VM3
vf 0: vlan 1000
vf 1: vlan 1000
vf 2: vlan 1001
vf 3: vlan 1001
If we tcpdump on VF3, we see all the packets, even those transmitted
on vlan 1000.
This behavior prevents to bridge VF1 and VF2 in VM2, because it will
create a loop: packets transmitted on VF1 will be received by VF2 and
vice-versa, and bridged again through the software bridge.
This patch remove the activation of VLAN Promiscuous when a VF enables
the promiscuous mode. However, the IXGBE_VMOLR_UPE bit (Unicast
Promiscuous) is kept, so that a VF receives all packets that has the
same VLAN, whatever the destination MAC address.
Fixes: 8443c1a4b1 ("ixgbe, ixgbevf: Add new mbox API xcast mode")
Cc: stable@vger.kernel.org
Cc: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Signed-off-by: Olivier Matz <olivier.matz@6wind.com>
Tested-by: Konrad Jankowski <konrad0.jankowski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 803e9895ea2b0fe80bc85980ae2d7a7e44037914 upstream.
After a VF requested to remove the promiscuous flag on an interface, the
broadcast packets are not received anymore. This breaks some protocols
like ARP.
In ixgbe_update_vf_xcast_mode(), we should keep the IXGBE_VMOLR_BAM
bit (Broadcast Accept) on promiscuous removal.
This flag is already set by default in ixgbe_set_vmolr() on VF reset.
Fixes: 8443c1a4b1 ("ixgbe, ixgbevf: Add new mbox API xcast mode")
Cc: stable@vger.kernel.org
Cc: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Signed-off-by: Olivier Matz <olivier.matz@6wind.com>
Tested-by: Konrad Jankowski <konrad0.jankowski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit d1bc532e99becf104635ed4da6fefa306f452321 ]
Move desc_array from the driver to the pool. The reason behind this is
that we can then reuse this array as a temporary storage for descriptors
in all zero-copy drivers that use the batched interface. This will make
it easier to add batching to more drivers.
i40e is the only driver that has a batched Tx zero-copy
implementation, so no need to touch any other driver.
Signed-off-by: Magnus Karlsson <magnus.karlsson@intel.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Reviewed-by: Alexander Lobakin <alexandr.lobakin@intel.com>
Link: https://lore.kernel.org/bpf/20220125160446.78976-6-maciej.fijalkowski@intel.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
Fix a crash in the zero-copy driver that occurs when it fails to
allocate buffers from user-space. This crash can easily be triggered
by a malicious program that does not provide any buffers in the fill
ring for the kernel to use.
Note that this bug does not exist in upstream since the batched buffer
allocation interface got introduced in 5.16 and replaced this code.
Reported-by: Jeff Shaw <jeffrey.b.shaw@intel.com>
Tested-by: Jeff Shaw <jeffrey.b.shaw@intel.com>
Signed-off-by: Magnus Karlsson <magnus.karlsson@intel.com>
Acked-by: Maciej Fijalkowski <maciej.fijalkowski@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 942d2ad5d2e0df758a645ddfadffde2795322728 ]
igb_read_phy_reg() will silently return, leaving phy_data untouched, if
hw->ops.read_reg isn't set. Depending on the uninitialized value of
phy_data, this led to the phy status check either succeeding immediately
or looping continuously for 2 seconds before emitting a noisy err-level
timeout. This message went out to the console even though there was no
actual problem.
Instead, first check if there is read_reg function pointer. If not,
proceed without trying to check the phy status register.
Fixes: b72f3f7200 ("igb: When GbE link up, wait for Remote receiver status condition")
Signed-off-by: Kevin Mitchell <kevmitch@arista.com>
Tested-by: Gurucharan <gurucharanx.g@intel.com> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit bf13502ed5f941b0777b3fd1e24dac5d93f3886c ]
Adaptive-rx and Adaptive-tx are interrupt moderation settings
that can be enabled/disabled using ethtool:
ethtool -C ethX adaptive-rx on/off adaptive-tx on/off
Unfortunately those settings are getting cleared after
changing number of queues, or in ethtool world 'channels':
ethtool -L ethX rx 1 tx 1
Clearing was happening due to introduction of bit fields
in ice_ring_container struct. This way only itr_setting
bits were rebuilt during ice_vsi_rebuild_set_coalesce().
Introduce an anonymous struct of bitfields and create a
union to refer to them as a single variable.
This way variable can be easily saved and restored.
Fixes: 61dc79ced7 ("ice: Restore interrupt throttle settings after VSI rebuild")
Signed-off-by: Michal Wilczynski <michal.wilczynski@intel.com>
Tested-by: Gurucharan <gurucharanx.g@intel.com> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit dc23715cf30a9acb808f5b08962877c390d3e6ea ]
Currently ice_container_type is scoped only for ice_ethtool.c. Next
commit that will split the ice_ring struct onto Rx/Tx specific ring
structs is going to also modify the type of linked list of rings that is
within ice_ring_container. Therefore, the functions that are taking the
ice_ring_container as an input argument will need to be aware of a ring
type that will be looked up.
Embed ice_container_type within ice_ring_container and initialize it
properly when allocating the q_vectors.
Signed-off-by: Maciej Fijalkowski <maciej.fijalkowski@intel.com>
Tested-by: Gurucharan G <gurucharanx.g@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 31b6298fd8e29effe9ed6b77351ac5969be56ce0 ]
The hardware statistics counters are not cleared during resets so the
drivers first access is to initialize the baseline and then subsequent
reads are for reporting the counters. The statistics counters are read
during the watchdog subtask when the interface is up. If the baseline
is not initialized before the interface is up, then there can be a brief
window in which some traffic can be transmitted/received before the
initial baseline reading takes place.
Directly initialize ethtool statistics in driver open so the baseline will
be initialized when the interface is up, and any dropped packets
incremented before the interface is up won't be reported.
Fixes: 28dc1b86f8ea9 ("ice: ignore dropped packets during init")
Signed-off-by: Paul Greenwalt <paul.greenwalt@intel.com>
Tested-by: Gurucharan <gurucharanx.g@intel.com> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 4503cc7fdf9a84cd631b0cb8ecb3c9b1bdbf3594 ]
Do not allow to write timestamps on RX rings if PF is being configured.
When PF is being configured RX rings can be freed or rebuilt. If at the
same time timestamps are updated, the kernel will crash by dereferencing
null RX ring pointer.
PID: 1449 TASK: ff187d28ed658040 CPU: 34 COMMAND: "ice-ptp-0000:51"
#0 [ff1966a94a713bb0] machine_kexec at ffffffff9d05a0be
#1 [ff1966a94a713c08] __crash_kexec at ffffffff9d192e9d
#2 [ff1966a94a713cd0] crash_kexec at ffffffff9d1941bd
#3 [ff1966a94a713ce8] oops_end at ffffffff9d01bd54
#4 [ff1966a94a713d08] no_context at ffffffff9d06bda4
#5 [ff1966a94a713d60] __bad_area_nosemaphore at ffffffff9d06c10c
#6 [ff1966a94a713da8] do_page_fault at ffffffff9d06cae4
#7 [ff1966a94a713de0] page_fault at ffffffff9da0107e
[exception RIP: ice_ptp_update_cached_phctime+91]
RIP: ffffffffc076db8b RSP: ff1966a94a713e98 RFLAGS: 00010246
RAX: 16e3db9c6b7ccae4 RBX: ff187d269dd3c180 RCX: ff187d269cd4d018
RDX: 0000000000000000 RSI: 0000000000000000 RDI: 0000000000000000
RBP: ff187d269cfcc644 R8: ff187d339b9641b0 R9: 0000000000000000
R10: 0000000000000002 R11: 0000000000000000 R12: ff187d269cfcc648
R13: ffffffff9f128784 R14: ffffffff9d101b70 R15: ff187d269cfcc640
ORIG_RAX: ffffffffffffffff CS: 0010 SS: 0018
#8 [ff1966a94a713ea0] ice_ptp_periodic_work at ffffffffc076dbef [ice]
#9 [ff1966a94a713ee0] kthread_worker_fn at ffffffff9d101c1b
#10 [ff1966a94a713f10] kthread at ffffffff9d101b4d
#11 [ff1966a94a713f50] ret_from_fork at ffffffff9da0023f
Fixes: 77a781155a ("ice: enable receive hardware timestamping")
Signed-off-by: Arkadiusz Kubalewski <arkadiusz.kubalewski@intel.com>
Reviewed-by: Michal Schmidt <mschmidt@redhat.com>
Tested-by: Dave Cain <dcain@redhat.com>
Tested-by: Gurucharan <gurucharanx.g@intel.com> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 3f95a7472d14abef284d8968734fe2ae7ff4845f upstream.
The bug is here:
ret = i40e_add_macvlan_filter(hw, ch->seid, vdev->dev_addr, &aq_err);
The list iterator 'ch' will point to a bogus position containing
HEAD if the list is empty or no element is found. This case must
be checked before any use of the iterator, otherwise it will
lead to a invalid memory access.
To fix this bug, use a new variable 'iter' as the list iterator,
while use the origin variable 'ch' as a dedicated pointer to
point to the found element.
Cc: stable@vger.kernel.org
Fixes: 1d8d80b4e4 ("i40e: Add macvlan support on i40e")
Signed-off-by: Xiaomeng Tong <xiam0nd.tong@gmail.com>
Tested-by: Gurucharan <gurucharanx.g@intel.com> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Link: https://lore.kernel.org/r/20220510204846.2166999-1-anthony.l.nguyen@intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit a11b6c1a383ff092f432e040c20e032503785d47 ]
Read stale PTP Tx timestamps from PHY on cleanup.
After running out of Tx timestamps request handlers, hardware (HW) stops
reporting finished requests. Function ice_ptp_tx_tstamp_cleanup() used
to only clean up stale handlers in driver and was leaving the hardware
registers not read. Not reading stale PTP Tx timestamps prevents next
interrupts from arriving and makes timestamping unusable.
Fixes: ea9b847cda ("ice: enable transmit timestamps for E810 devices")
Signed-off-by: Michal Michalik <michal.michalik@intel.com>
Reviewed-by: Jacob Keller <jacob.e.keller@intel.com>
Reviewed-by: Paul Menzel <pmenzel@molgen.mpg.de>
Tested-by: Gurucharan <gurucharanx.g@intel.com> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 486b9eee57ddca5c9a2d59fc41153f36002e0a00 ]
Function ice_plug_aux_dev() assigns pf->adev field too early prior
aux device initialization and on other side ice_unplug_aux_dev()
starts aux device deinit and at the end assigns NULL to pf->adev.
This is wrong because pf->adev should always be non-NULL only when
aux device is fully initialized and ready. This wrong order causes
a crash when ice_send_event_to_aux() call occurs because that function
depends on non-NULL value of pf->adev and does not assume that
aux device is half-initialized or half-destroyed.
After order correction the race window is tiny but it is still there,
as Leon mentioned and manipulation with pf->adev needs to be protected
by mutex.
Fix (un-)plugging functions so pf->adev field is set after aux device
init and prior aux device destroy and protect pf->adev assignment by
new mutex. This mutex is also held during ice_send_event_to_aux()
call to ensure that aux device is valid during that call.
Note that device lock used ice_send_event_to_aux() needs to be kept
to avoid race with aux drv unload.
Reproducer:
cycle=1
while :;do
echo "#### Cycle: $cycle"
ip link set ens7f0 mtu 9000
ip link add bond0 type bond mode 1 miimon 100
ip link set bond0 up
ifenslave bond0 ens7f0
ip link set bond0 mtu 9000
ethtool -L ens7f0 combined 1
ip link del bond0
ip link set ens7f0 mtu 1500
sleep 1
let cycle++
done
In short when the device is added/removed to/from bond the aux device
is unplugged/plugged. When MTU of the device is changed an event is
sent to aux device asynchronously. This can race with (un)plugging
operation and because pf->adev is set too early (plug) or too late
(unplug) the function ice_send_event_to_aux() can touch uninitialized
or destroyed fields. In the case of crash below pf->adev->dev.mutex.
Crash:
[ 53.372066] bond0: (slave ens7f0): making interface the new active one
[ 53.378622] bond0: (slave ens7f0): Enslaving as an active interface with an u
p link
[ 53.386294] IPv6: ADDRCONF(NETDEV_CHANGE): bond0: link becomes ready
[ 53.549104] bond0: (slave ens7f1): Enslaving as a backup interface with an up
link
[ 54.118906] ice 0000:ca:00.0 ens7f0: Number of in use tx queues changed inval
idating tc mappings. Priority traffic classification disabled!
[ 54.233374] ice 0000:ca:00.1 ens7f1: Number of in use tx queues changed inval
idating tc mappings. Priority traffic classification disabled!
[ 54.248204] bond0: (slave ens7f0): Releasing backup interface
[ 54.253955] bond0: (slave ens7f1): making interface the new active one
[ 54.274875] bond0: (slave ens7f1): Releasing backup interface
[ 54.289153] bond0 (unregistering): Released all slaves
[ 55.383179] MII link monitoring set to 100 ms
[ 55.398696] bond0: (slave ens7f0): making interface the new active one
[ 55.405241] BUG: kernel NULL pointer dereference, address: 0000000000000080
[ 55.405289] bond0: (slave ens7f0): Enslaving as an active interface with an u
p link
[ 55.412198] #PF: supervisor write access in kernel mode
[ 55.412200] #PF: error_code(0x0002) - not-present page
[ 55.412201] PGD 25d2ad067 P4D 0
[ 55.412204] Oops: 0002 [#1] PREEMPT SMP NOPTI
[ 55.412207] CPU: 0 PID: 403 Comm: kworker/0:2 Kdump: loaded Tainted: G S
5.17.0-13579-g57f2d6540f03 #1
[ 55.429094] bond0: (slave ens7f1): Enslaving as a backup interface with an up
link
[ 55.430224] Hardware name: Dell Inc. PowerEdge R750/06V45N, BIOS 1.4.4 10/07/
2021
[ 55.430226] Workqueue: ice ice_service_task [ice]
[ 55.468169] RIP: 0010:mutex_unlock+0x10/0x20
[ 55.472439] Code: 0f b1 13 74 96 eb e0 4c 89 ee eb d8 e8 79 54 ff ff 66 0f 1f 84 00 00 00 00 00 0f 1f 44 00 00 65 48 8b 04 25 40 ef 01 00 31 d2 <f0> 48 0f b1 17 75 01 c3 e9 e3 fe ff ff 0f 1f 00 0f 1f 44 00 00 48
[ 55.491186] RSP: 0018:ff4454230d7d7e28 EFLAGS: 00010246
[ 55.496413] RAX: ff1a79b208b08000 RBX: ff1a79b2182e8880 RCX: 0000000000000001
[ 55.503545] RDX: 0000000000000000 RSI: ff4454230d7d7db0 RDI: 0000000000000080
[ 55.510678] RBP: ff1a79d1c7e48b68 R08: ff4454230d7d7db0 R09: 0000000000000041
[ 55.517812] R10: 00000000000000a5 R11: 00000000000006e6 R12: ff1a79d1c7e48bc0
[ 55.524945] R13: 0000000000000000 R14: ff1a79d0ffc305c0 R15: 0000000000000000
[ 55.532076] FS: 0000000000000000(0000) GS:ff1a79d0ffc00000(0000) knlGS:0000000000000000
[ 55.540163] CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
[ 55.545908] CR2: 0000000000000080 CR3: 00000003487ae003 CR4: 0000000000771ef0
[ 55.553041] DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000
[ 55.560173] DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400
[ 55.567305] PKRU: 55555554
[ 55.570018] Call Trace:
[ 55.572474] <TASK>
[ 55.574579] ice_service_task+0xaab/0xef0 [ice]
[ 55.579130] process_one_work+0x1c5/0x390
[ 55.583141] ? process_one_work+0x390/0x390
[ 55.587326] worker_thread+0x30/0x360
[ 55.590994] ? process_one_work+0x390/0x390
[ 55.595180] kthread+0xe6/0x110
[ 55.598325] ? kthread_complete_and_exit+0x20/0x20
[ 55.603116] ret_from_fork+0x1f/0x30
[ 55.606698] </TASK>
Fixes: f9f5301e7e ("ice: Register auxiliary device to provide RDMA")
Reviewed-by: Leon Romanovsky <leonro@nvidia.com>
Signed-off-by: Ivan Vecera <ivecera@redhat.com>
Reviewed-by: Dave Ertman <david.m.ertman@intel.com>
Tested-by: Gurucharan <gurucharanx.g@intel.com> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 04ebaa1cfddae5f240cc7404f009133bb0389a47 upstream.
When we decode the latency and the max_latency, u16 value may not fit
the required size and could lead to the wrong LTR representation.
Scaling is represented as:
scale 0 - 1 (2^(5*0)) = 2^0
scale 1 - 32 (2^(5 *1))= 2^5
scale 2 - 1024 (2^(5 *2)) =2^10
scale 3 - 32768 (2^(5 *3)) =2^15
scale 4 - 1048576 (2^(5 *4)) = 2^20
scale 5 - 33554432 (2^(5 *4)) = 2^25
scale 4 and scale 5 required 20 and 25 bits respectively.
scale 6 reserved.
Replace the u16 type with the u32 type and allow corrected LTR
representation.
Cc: stable@vger.kernel.org
Fixes: 44a13a5d99 ("e1000e: Fix the max snoop/no-snoop latency for 10M")
Reported-by: James Hutchinson <jahutchinson99@googlemail.com>
Link: https://bugzilla.kernel.org/show_bug.cgi?id=215689
Suggested-by: Dima Ruinskiy <dima.ruinskiy@intel.com>
Signed-off-by: Sasha Neftin <sasha.neftin@intel.com>
Tested-by: Naama Meir <naamax.meir@linux.intel.com>
Tested-by: James Hutchinson <jahutchinson99@googlemail.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 822f52e7efdc88fccffb9fbf6250a4b7666a0b0f ]
Some mainboard/CPU combinations, in particular, Alder Lake-S with a
W680 mainboard, have shown problems (system hangs usually, no kernel
logs) with suspend/resume when PCIe PTM is enabled and active. In some
cases, it could be reproduced when removing the igc module.
The best we can do is to stop PTM dialogs from the downstream/device
side before the interface is brought down. PCIe PTM will be re-enabled
when the interface is being brought up.
Fixes: a90ec84837 ("igc: Add support for PTP getcrosststamp()")
Signed-off-by: Vinicius Costa Gomes <vinicius.gomes@intel.com>
Tested-by: Naama Meir <naamax.meir@linux.intel.com>
Acked-by: Paul Menzel <pmenzel@molgen.mpg.de>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 907862e9aef75bf89e2b265efcc58870be06081e ]
An infinite loop may occur if we fail to acquire the HW semaphore,
which is needed for resource release.
This will typically happen if the hardware is surprise-removed.
At this stage there is nothing to do, except log an error and quit.
Fixes: c0071c7aa5 ("igc: Add HW initialization code")
Suggested-by: Dima Ruinskiy <dima.ruinskiy@intel.com>
Signed-off-by: Sasha Neftin <sasha.neftin@intel.com>
Tested-by: Naama Meir <naamax.meir@linux.intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 72b915a2b444e9247c9d424a840e94263db07c27 ]
ICE_DOWN is dedicated for pf->state. Check for ICE_VSI_DOWN being set on
vsi->state in ice_xsk_wakeup().
Fixes: 2d4238f556 ("ice: Add support for AF_XDP")
Signed-off-by: Maciej Fijalkowski <maciej.fijalkowski@intel.com>
Tested-by: Shwetha Nagaraju <shwetha.nagaraju@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f9124c68f05ffdb87a47e3ea6d5fae9dad7cb6eb ]
Unfortunately, the ice driver doesn't respect the RCU critical section that
XSK wakeup is surrounded with. To fix this, add synchronize_rcu() calls to
paths that destroy resources that might be in use.
This was addressed in other AF_XDP ZC enabled drivers, for reference see
for example commit b3873a5be7 ("net/i40e: Fix concurrency issues
between config flow and XSK")
Fixes: efc2214b60 ("ice: Add support for XDP")
Fixes: 2d4238f556 ("ice: Add support for AF_XDP")
Signed-off-by: Maciej Fijalkowski <maciej.fijalkowski@intel.com>
Tested-by: Shwetha Nagaraju <shwetha.nagaraju@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 05ef6813b234db3196f083b91db3963f040b65bb ]
Disable check for queue being enabled in ice_vc_dis_qs_msg, because
there could be a case when queues were created, but were not enabled.
We still need to delete those queues.
Normal workflow for VF looks like:
Enable path:
VIRTCHNL_OP_ADD_ETH_ADDR (opcode 10)
VIRTCHNL_OP_CONFIG_VSI_QUEUES (opcode 6)
VIRTCHNL_OP_ENABLE_QUEUES (opcode 8)
Disable path:
VIRTCHNL_OP_DISABLE_QUEUES (opcode 9)
VIRTCHNL_OP_DEL_ETH_ADDR (opcode 11)
The issue appears only in stress conditions when VF is enabled and
disabled very fast.
Eventually there will be a case, when queues are created by
VIRTCHNL_OP_CONFIG_VSI_QUEUES, but are not enabled by
VIRTCHNL_OP_ENABLE_QUEUES.
In turn, these queues are not deleted by VIRTCHNL_OP_DISABLE_QUEUES,
because there is a check whether queues are enabled in
ice_vc_dis_qs_msg.
When we bring up the VF again, we will see the "Failed to set LAN Tx queue
context" error during VIRTCHNL_OP_CONFIG_VSI_QUEUES step. This
happens because old 16 queues were not deleted and VF requests to create
16 more, but ice_sched_get_free_qparent in ice_ena_vsi_txq would fail to
find a parent node for first newly requested queue (because all nodes
are allocated to 16 old queues).
Testing Hints:
Just enable and disable VF fast enough, so it would be disabled before
reaching VIRTCHNL_OP_ENABLE_QUEUES.
while true; do
ip link set dev ens785f0v0 up
sleep 0.065 # adjust delay value for you machine
ip link set dev ens785f0v0 down
done
Fixes: 77ca27c417 ("ice: add support for virtchnl_queue_select.[tx|rx]_queues bitmap")
Signed-off-by: Anatolii Gerasymenko <anatolii.gerasymenko@intel.com>
Tested-by: Konrad Jankowski <konrad0.jankowski@intel.com>
Signed-off-by: Alice Michael <alice.michael@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit ccfee1822042b87e5135d33cad8ea353e64612d2 ]
When VF is freshly created, but not brought up, ring->txq_teid
value is by default set to 0.
But 0 is a valid TEID. On some platforms the Root Node of
Tx scheduler has a TEID = 0. This can cause issues as shown below.
The proper way is to set ring->txq_teid to ICE_INVAL_TEID (0xFFFFFFFF).
Testing Hints:
echo 1 > /sys/class/net/ens785f0/device/sriov_numvfs
ip link set dev ens785f0v0 up
ip link set dev ens785f0v0 down
If we have freshly created VF and quickly turn it on and off, so there
would be no time to reach VIRTCHNL_OP_CONFIG_VSI_QUEUES stage, then
VIRTCHNL_OP_DISABLE_QUEUES stage will fail with error:
[ 639.531454] disable queue 89 failed 14
[ 639.532233] Failed to disable LAN Tx queues, error: ICE_ERR_AQ_ERROR
[ 639.533107] ice 0000:02:00.0: Failed to stop Tx ring 0 on VSI 5
The reason for the fail is that we are trying to send AQ command to
delete queue 89, which has never been created and receive an "invalid
argument" error from firmware.
As this queue has never been created, it's teid and ring->txq_teid
have default value 0.
ice_dis_vsi_txq has a check against non-existent queues:
node = ice_sched_find_node_by_teid(pi->root, q_teids[i]);
if (!node)
continue;
But on some platforms the Root Node of Tx scheduler has a teid = 0.
Hence, ice_sched_find_node_by_teid finds a node with teid = 0 (it is
pi->root), and we go further to submit an erroneous request to firmware.
Fixes: 37bb839012 ("ice: Move common functions out of ice_main.c part 7/7")
Signed-off-by: Anatolii Gerasymenko <anatolii.gerasymenko@intel.com>
Reviewed-by: Maciej Fijalkowski <maciej.fijalkowski@intel.com>
Tested-by: Konrad Jankowski <konrad0.jankowski@intel.com>
Signed-off-by: Alice Michael <alice.michael@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit bd8c624c0cd59de0032752ba3001c107bba97f7b ]
VSI is set as default forwarding one when promisc mode is set for
PF interface, when PF is switched to switchdev mode or when VF
driver asks to enable allmulticast or promisc mode for the VF
interface (when vf-true-promisc-support priv flag is off).
The third case is buggy because in that case VSI associated with
VF remains as default one after VF removal.
Reproducer:
1. Create VF
echo 1 > sys/class/net/ens7f0/device/sriov_numvfs
2. Enable allmulticast or promisc mode on VF
ip link set ens7f0v0 allmulticast on
ip link set ens7f0v0 promisc on
3. Delete VF
echo 0 > sys/class/net/ens7f0/device/sriov_numvfs
4. Try to enable promisc mode on PF
ip link set ens7f0 promisc on
Although it looks that promisc mode on PF is enabled the opposite
is true because ice_vsi_sync_fltr() responsible for IFF_PROMISC
handling first checks if any other VSI is set as default forwarding
one and if so the function does not do anything. At this point
it is not possible to enable promisc mode on PF without re-probe
device.
To resolve the issue this patch clear default forwarding VSI
during ice_vsi_release() when the VSI to be released is the default
one.
Fixes: 01b5e89aab ("ice: Add VF promiscuous support")
Signed-off-by: Ivan Vecera <ivecera@redhat.com>
Reviewed-by: Michal Swiatkowski <michal.swiatkowski@linux.intel.com>
Reviewed-by: Maciej Fijalkowski <maciej.fijalkowski@intel.com>
Signed-off-by: Alice Michael <alice.michael@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 5a3156932da06f09953764de113419f254086faf ]
ice_send_event_to_aux() eventually descends to mutex_lock()
(-> might_sched()), so it must not be called under non-task
context. However, at least two fixes have happened already for the
bug splats occurred due to this function being called from atomic
context.
To make the emergency landings softer, bail out early when executed
in non-task context emitting a warn splat only once. This way we
trade some events being potentially lost for system stability and
avoid any related hangs and crashes.
Fixes: 348048e724 ("ice: Implement iidc operations")
Signed-off-by: Alexander Lobakin <alexandr.lobakin@intel.com>
Tested-by: Michal Kubiak <michal.kubiak@intel.com>
Reviewed-by: Maciej Fijalkowski <maciej.fijalkowski@intel.com>
Acked-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 32d53c0aa3a7b727243473949bad2a830b908edc ]
There's a kernel BUG splat on processing aux critical error
interrupts in ice_misc_intr():
[ 2100.917085] BUG: scheduling while atomic: swapper/15/0/0x00010000
...
[ 2101.060770] Call Trace:
[ 2101.063229] <IRQ>
[ 2101.065252] dump_stack+0x41/0x60
[ 2101.068587] __schedule_bug.cold.100+0x4c/0x58
[ 2101.073060] __schedule+0x6a4/0x830
[ 2101.076570] schedule+0x35/0xa0
[ 2101.079727] schedule_preempt_disabled+0xa/0x10
[ 2101.084284] __mutex_lock.isra.7+0x310/0x420
[ 2101.088580] ? ice_misc_intr+0x201/0x2e0 [ice]
[ 2101.093078] ice_send_event_to_aux+0x25/0x70 [ice]
[ 2101.097921] ice_misc_intr+0x220/0x2e0 [ice]
[ 2101.102232] __handle_irq_event_percpu+0x40/0x180
[ 2101.106965] handle_irq_event_percpu+0x30/0x80
[ 2101.111434] handle_irq_event+0x36/0x53
[ 2101.115292] handle_edge_irq+0x82/0x190
[ 2101.119148] handle_irq+0x1c/0x30
[ 2101.122480] do_IRQ+0x49/0xd0
[ 2101.125465] common_interrupt+0xf/0xf
[ 2101.129146] </IRQ>
...
As Andrew correctly mentioned previously[0], the following call
ladder happens:
ice_misc_intr() <- hardirq
ice_send_event_to_aux()
device_lock()
mutex_lock()
might_sleep()
might_resched() <- oops
Add a new PF state bit which indicates that an aux critical error
occurred and serve it in ice_service_task() in process context.
The new ice_pf::oicr_err_reg is read-write in both hardirq and
process contexts, but only 3 bits of non-critical data probably
aren't worth explicit synchronizing (and they're even in the same
byte [31:24]).
[0] https://lore.kernel.org/all/YeSRUVmrdmlUXHDn@lunn.ch
Fixes: 348048e724 ("ice: Implement iidc operations")
Signed-off-by: Alexander Lobakin <alexandr.lobakin@intel.com>
Tested-by: Michal Kubiak <michal.kubiak@intel.com>
Acked-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e62ad74aa534404b3ee7e250b114a3536ac56987 ]
On changing the RX ring parameters igb uses a hack to avoid a warning
when calling xdp_rxq_info_reg via igb_setup_rx_resources. It just
clears the struct xdp_rxq_info content.
Instead, change this to unregister if we're already registered. Align
code to the igc code.
Fixes: 9cbc948b5a ("igb: add XDP support")
Signed-off-by: Corinna Vinschen <vinschen@redhat.com>
Acked-by: Vinicius Costa Gomes <vinicius.gomes@intel.com>
Tested-by: Sandeep Penigalapati <sandeep.penigalapati@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f322a620be69e95594eda89502b478aa7dbf6ec2 ]
For now, if the XDP prog returns XDP_PASS on XSK, the metadata
will be lost as it doesn't get copied to the skb.
Copy it along with the frame headers. Account its size on skb
allocation, and when copying just treat it as a part of the frame
and do a pull after to "move" it to the "reserved" zone.
net_prefetch() xdp->data_meta and align the copy size to speed-up
memcpy() a little and better match ixgbe_construct_skb().
Fixes: d0bcacd0a1 ("ixgbe: add AF_XDP zero-copy Rx support")
Suggested-by: Jesper Dangaard Brouer <brouer@redhat.com>
Suggested-by: Maciej Fijalkowski <maciej.fijalkowski@intel.com>
Signed-off-by: Alexander Lobakin <alexandr.lobakin@intel.com>
Reviewed-by: Michal Swiatkowski <michal.swiatkowski@linux.intel.com>
Tested-by: Sandeep Penigalapati <sandeep.penigalapati@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 8f405221a73a53234486c185d8ef647377a53cc6 ]
{__,}napi_alloc_skb() allocates and reserves additional NET_SKB_PAD
+ NET_IP_ALIGN for any skb.
OTOH, ixgbe_construct_skb_zc() currently allocates and reserves
additional `xdp->data - xdp->data_hard_start`, which is
XDP_PACKET_HEADROOM for XSK frames.
There's no need for that at all as the frame is post-XDP and will
go only to the networking stack core.
Pass the size of the actual data only to __napi_alloc_skb() and
don't reserve anything. This will give enough headroom for stack
processing.
Fixes: d0bcacd0a1 ("ixgbe: add AF_XDP zero-copy Rx support")
Signed-off-by: Alexander Lobakin <alexandr.lobakin@intel.com>
Reviewed-by: Michal Swiatkowski <michal.swiatkowski@linux.intel.com>
Tested-by: Sandeep Penigalapati <sandeep.penigalapati@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 1fbdaa13386804a31eefd3db3c5fe00e80ce9bc3 ]
To not dereference bi->xdp each time in ixgbe_construct_skb_zc(),
pass bi->xdp as an argument instead of bi. We can also call
xsk_buff_free() outside of the function as well as assign bi->xdp
to NULL, which seems to make it closer to its name.
Suggested-by: Maciej Fijalkowski <maciej.fijalkowski@intel.com>
Signed-off-by: Alexander Lobakin <alexandr.lobakin@intel.com>
Tested-by: Sandeep Penigalapati <sandeep.penigalapati@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f9e61d365bafdee40fe2586fc6be490c3e824dad ]
{__,}napi_alloc_skb() allocates and reserves additional NET_SKB_PAD
+ NET_IP_ALIGN for any skb.
OTOH, igc_construct_skb_zc() currently allocates and reserves
additional `xdp->data_meta - xdp->data_hard_start`, which is about
XDP_PACKET_HEADROOM for XSK frames.
There's no need for that at all as the frame is post-XDP and will
go only to the networking stack core.
Pass the size of the actual data only (+ meta) to
__napi_alloc_skb() and don't reserve anything. This will give
enough headroom for stack processing.
Also, net_prefetch() xdp->data_meta and align the copy size to
speed-up memcpy() a little and better match igc_construct_skb().
Fixes: fc9df2a0b5 ("igc: Enable RX via AF_XDP zero-copy")
Signed-off-by: Alexander Lobakin <alexandr.lobakin@intel.com>
Reviewed-by: Michal Swiatkowski <michal.swiatkowski@linux.intel.com>
Tested-by: Nechama Kraus <nechamax.kraus@linux.intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 6dba29537c0f639b482bd8f8bbd50ab4ae74b48d ]
For now, if the XDP prog returns XDP_PASS on XSK, the metadata will
be lost as it doesn't get copied to the skb.
Copy it along with the frame headers. Account its size on skb
allocation, and when copying just treat it as a part of the frame
and do a pull after to "move" it to the "reserved" zone.
net_prefetch() xdp->data_meta and align the copy size to speed-up
memcpy() a little and better match i40e_construct_skb().
Fixes: 0a714186d3 ("i40e: add AF_XDP zero-copy Rx support")
Suggested-by: Jesper Dangaard Brouer <brouer@redhat.com>
Suggested-by: Maciej Fijalkowski <maciej.fijalkowski@intel.com>
Signed-off-by: Alexander Lobakin <alexandr.lobakin@intel.com>
Reviewed-by: Michal Swiatkowski <michal.swiatkowski@linux.intel.com>
Tested-by: Kiran Bhandare <kiranx.bhandare@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit bc97f9c6f988b31b728eb47a94ca825401dbeffe ]
{__,}napi_alloc_skb() allocates and reserves additional NET_SKB_PAD
+ NET_IP_ALIGN for any skb.
OTOH, i40e_construct_skb_zc() currently allocates and reserves
additional `xdp->data - xdp->data_hard_start`, which is
XDP_PACKET_HEADROOM for XSK frames.
There's no need for that at all as the frame is post-XDP and will
go only to the networking stack core.
Pass the size of the actual data only to __napi_alloc_skb() and
don't reserve anything. This will give enough headroom for stack
processing.
Fixes: 0a714186d3 ("i40e: add AF_XDP zero-copy Rx support")
Signed-off-by: Alexander Lobakin <alexandr.lobakin@intel.com>
Reviewed-by: Michal Swiatkowski <michal.swiatkowski@linux.intel.com>
Acked-by: Jesper Dangaard Brouer <brouer@redhat.com>
Tested-by: Kiran Bhandare <kiranx.bhandare@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b04683ff8f0823b869c219c78ba0d974bddea0b5 ]
Recent commit 974578017fc1 ("iavf: Add waiting so the port is
initialized in remove") adds a wait-loop at the beginning of
iavf_remove() to ensure that port initialization is finished
prior unregistering net device. This causes a regression
in reboot/shutdown scenario because in this case callback
iavf_shutdown() is called and this callback detaches the device,
makes it down if it is running and sets its state to __IAVF_REMOVE.
Later shutdown callback of associated PF driver (e.g. ice_shutdown)
is called. That callback calls among other things sriov_disable()
that calls indirectly iavf_remove() (see stack trace below).
As the adapter state is already __IAVF_REMOVE then the mentioned
loop is end-less and shutdown process hangs.
The patch fixes this by checking adapter's state at the beginning
of iavf_remove() and skips the rest of the function if the adapter
is already in remove state (shutdown is in progress).
Reproducer:
1. Create VF on PF driven by ice or i40e driver
2. Ensure that the VF is bound to iavf driver
3. Reboot
[52625.981294] sysrq: SysRq : Show Blocked State
[52625.988377] task:reboot state:D stack: 0 pid:17359 ppid: 1 f2
[52625.996732] Call Trace:
[52625.999187] __schedule+0x2d1/0x830
[52626.007400] schedule+0x35/0xa0
[52626.010545] schedule_hrtimeout_range_clock+0x83/0x100
[52626.020046] usleep_range+0x5b/0x80
[52626.023540] iavf_remove+0x63/0x5b0 [iavf]
[52626.027645] pci_device_remove+0x3b/0xc0
[52626.031572] device_release_driver_internal+0x103/0x1f0
[52626.036805] pci_stop_bus_device+0x72/0xa0
[52626.040904] pci_stop_and_remove_bus_device+0xe/0x20
[52626.045870] pci_iov_remove_virtfn+0xba/0x120
[52626.050232] sriov_disable+0x2f/0xe0
[52626.053813] ice_free_vfs+0x7c/0x340 [ice]
[52626.057946] ice_remove+0x220/0x240 [ice]
[52626.061967] ice_shutdown+0x16/0x50 [ice]
[52626.065987] pci_device_shutdown+0x34/0x60
[52626.070086] device_shutdown+0x165/0x1c5
[52626.074011] kernel_restart+0xe/0x30
[52626.077593] __do_sys_reboot+0x1d2/0x210
[52626.093815] do_syscall_64+0x5b/0x1a0
[52626.097483] entry_SYSCALL_64_after_hwframe+0x65/0xca
Fixes: 974578017fc1 ("iavf: Add waiting so the port is initialized in remove")
Signed-off-by: Ivan Vecera <ivecera@redhat.com>
Link: https://lore.kernel.org/r/20220317104524.2802848-1-ivecera@redhat.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 16b2dd8cdf6f4e0597c34899de74b4d012b78188 ]
Fix double free possibility in iavf_disable_vf, as crit_lock is
freed in caller, iavf_reset_task. Add kernel-doc for iavf_disable_vf.
Remove mutex_unlock in iavf_disable_vf.
Without this patch there is double free scenario, when calling
iavf_reset_task.
Fixes: e85ff9c631e1 ("iavf: Fix deadlock in iavf_reset_task")
Signed-off-by: Przemyslaw Patynowski <przemyslawx.patynowski@intel.com>
Suggested-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Mateusz Palczewski <mateusz.palczewski@intel.com>
Tested-by: Konrad Jankowski <konrad0.jankowski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 5cb1ebdbc4342b1c2ce89516e19808d64417bdbc upstream.
Commit 5dbbbd01cbba83 ("ice: Avoid RTNL lock when re-creating
auxiliary device") changes a process of re-creation of aux device
so ice_plug_aux_dev() is called from ice_service_task() context.
This unfortunately opens a race window that can result in dead-lock
when interface has left LAG and immediately enters LAG again.
Reproducer:
```
#!/bin/sh
ip link add lag0 type bond mode 1 miimon 100
ip link set lag0
for n in {1..10}; do
echo Cycle: $n
ip link set ens7f0 master lag0
sleep 1
ip link set ens7f0 nomaster
done
```
This results in:
[20976.208697] Workqueue: ice ice_service_task [ice]
[20976.213422] Call Trace:
[20976.215871] __schedule+0x2d1/0x830
[20976.219364] schedule+0x35/0xa0
[20976.222510] schedule_preempt_disabled+0xa/0x10
[20976.227043] __mutex_lock.isra.7+0x310/0x420
[20976.235071] enum_all_gids_of_dev_cb+0x1c/0x100 [ib_core]
[20976.251215] ib_enum_roce_netdev+0xa4/0xe0 [ib_core]
[20976.256192] ib_cache_setup_one+0x33/0xa0 [ib_core]
[20976.261079] ib_register_device+0x40d/0x580 [ib_core]
[20976.266139] irdma_ib_register_device+0x129/0x250 [irdma]
[20976.281409] irdma_probe+0x2c1/0x360 [irdma]
[20976.285691] auxiliary_bus_probe+0x45/0x70
[20976.289790] really_probe+0x1f2/0x480
[20976.298509] driver_probe_device+0x49/0xc0
[20976.302609] bus_for_each_drv+0x79/0xc0
[20976.306448] __device_attach+0xdc/0x160
[20976.310286] bus_probe_device+0x9d/0xb0
[20976.314128] device_add+0x43c/0x890
[20976.321287] __auxiliary_device_add+0x43/0x60
[20976.325644] ice_plug_aux_dev+0xb2/0x100 [ice]
[20976.330109] ice_service_task+0xd0c/0xed0 [ice]
[20976.342591] process_one_work+0x1a7/0x360
[20976.350536] worker_thread+0x30/0x390
[20976.358128] kthread+0x10a/0x120
[20976.365547] ret_from_fork+0x1f/0x40
...
[20976.438030] task:ip state:D stack: 0 pid:213658 ppid:213627 flags:0x00004084
[20976.446469] Call Trace:
[20976.448921] __schedule+0x2d1/0x830
[20976.452414] schedule+0x35/0xa0
[20976.455559] schedule_preempt_disabled+0xa/0x10
[20976.460090] __mutex_lock.isra.7+0x310/0x420
[20976.464364] device_del+0x36/0x3c0
[20976.467772] ice_unplug_aux_dev+0x1a/0x40 [ice]
[20976.472313] ice_lag_event_handler+0x2a2/0x520 [ice]
[20976.477288] notifier_call_chain+0x47/0x70
[20976.481386] __netdev_upper_dev_link+0x18b/0x280
[20976.489845] bond_enslave+0xe05/0x1790 [bonding]
[20976.494475] do_setlink+0x336/0xf50
[20976.502517] __rtnl_newlink+0x529/0x8b0
[20976.543441] rtnl_newlink+0x43/0x60
[20976.546934] rtnetlink_rcv_msg+0x2b1/0x360
[20976.559238] netlink_rcv_skb+0x4c/0x120
[20976.563079] netlink_unicast+0x196/0x230
[20976.567005] netlink_sendmsg+0x204/0x3d0
[20976.570930] sock_sendmsg+0x4c/0x50
[20976.574423] ____sys_sendmsg+0x1eb/0x250
[20976.586807] ___sys_sendmsg+0x7c/0xc0
[20976.606353] __sys_sendmsg+0x57/0xa0
[20976.609930] do_syscall_64+0x5b/0x1a0
[20976.613598] entry_SYSCALL_64_after_hwframe+0x65/0xca
1. Command 'ip link ... set nomaster' causes that ice_plug_aux_dev()
is called from ice_service_task() context, aux device is created
and associated device->lock is taken.
2. Command 'ip link ... set master...' calls ice's notifier under
RTNL lock and that notifier calls ice_unplug_aux_dev(). That
function tries to take aux device->lock but this is already taken
by ice_plug_aux_dev() in step 1
3. Later ice_plug_aux_dev() tries to take RTNL lock but this is already
taken in step 2
4. Dead-lock
The patch fixes this issue by following changes:
- Bit ICE_FLAG_PLUG_AUX_DEV is kept to be set during ice_plug_aux_dev()
call in ice_service_task()
- The bit is checked in ice_clear_rdma_cap() and only if it is not set
then ice_unplug_aux_dev() is called. If it is set (in other words
plugging of aux device was requested and ice_plug_aux_dev() is
potentially running) then the function only clears the bit
- Once ice_plug_aux_dev() call (in ice_service_task) is finished
the bit ICE_FLAG_PLUG_AUX_DEV is cleared but it is also checked
whether it was already cleared by ice_clear_rdma_cap(). If so then
aux device is unplugged.
Signed-off-by: Ivan Vecera <ivecera@redhat.com>
Co-developed-by: Petr Oros <poros@redhat.com>
Signed-off-by: Petr Oros <poros@redhat.com>
Reviewed-by: Dave Ertman <david.m.ertman@intel.com>
Link: https://lore.kernel.org/r/20220310171641.3863659-1-ivecera@redhat.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit ad35ffa252af67d4cc7c744b9377a2b577748e3f ]
Change curr_link_speed advertised speed, due to
link_info.link_speed is not equal phy.curr_user_speed_req.
Without this patch it is impossible to set advertised
speed to same as link_speed.
Testing Hints: Try to set advertised speed
to 25G only with 25G default link (use ethtool -s 0x80000000)
Fixes: 48cb27f2fd ("ice: Implement handlers for ethtool PHY/link operations")
Signed-off-by: Grzegorz Siwik <grzegorz.siwik@intel.com>
Signed-off-by: Jedrzej Jagielski <jedrzej.jagielski@intel.com>
Tested-by: Gurucharan <gurucharanx.g@intel.com> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 3d97f1afd8d831e0c0dc1157418f94b8faa97b54 ]
ice_misc_intr() is an irq handler. It should not sleep.
Use GFP_ATOMIC instead of GFP_KERNEL when allocating some memory.
Fixes: 348048e724 ("ice: Implement iidc operations")
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Tested-by: Leszek Kaliszczuk <leszek.kaliszczuk@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 97b0129146b1544bbb0773585327896da3bb4e0a ]
When a bonded interface is destroyed, .ndo_change_mtu can be called
during the tear-down process while the RTNL lock is held. This is a
problem since the auxiliary driver linked to the LAN driver needs to be
notified of the MTU change, and this requires grabbing a device_lock on
the auxiliary_device's dev. Currently this is being attempted in the
same execution context as the call to .ndo_change_mtu which is causing a
dead-lock.
Move the notification of the changed MTU to a separate execution context
(watchdog service task) and eliminate the "before" notification.
Fixes: 348048e724 ("ice: Implement iidc operations")
Signed-off-by: Dave Ertman <david.m.ertman@intel.com>
Tested-by: Jonathan Toppins <jtoppins@redhat.com>
Tested-by: Gurucharan G <gurucharanx.g@intel.com> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 79498d5af8e458102242d1667cf44df1f1564e63 ]
The ice_vc_send_msg_to_vf function has logic to detect "failure"
responses being sent to a VF. If a VF is sent more than
ICE_DFLT_NUM_INVAL_MSGS_ALLOWED then the VF is marked as disabled.
Almost identical logic also existed in the i40e driver.
This logic was added to the ice driver in commit 1071a8358a ("ice:
Implement virtchnl commands for AVF support") which itself copied from
the i40e implementation in commit 5c3c48ac6b ("i40e: implement virtual
device interface").
Neither commit provides a proper explanation or justification of the
check. In fact, later commits to i40e changed the logic to allow
bypassing the check in some specific instances.
The "logic" for this seems to be that error responses somehow indicate a
malicious VF. This is not really true. The PF might be sending an error
for any number of reasons such as lack of resources, etc.
Additionally, this causes the PF to log an info message for every failed
VF response which may confuse users, and can spam the kernel log.
This behavior is not documented as part of any requirement for our
products and other operating system drivers such as the FreeBSD
implementation of our drivers do not include this type of check.
In fact, the change from dev_err to dev_info in i40e commit 18b7af57d9
("i40e: Lower some message levels") explains that these messages
typically don't actually indicate a real issue. It is quite likely that
a user who hits this in practice will be very confused as the VF will be
disabled without an obvious way to recover.
We already have robust malicious driver detection logic using actual
hardware detection mechanisms that detect and prevent invalid device
usage. Remove the logic since its not a documented requirement and the
behavior is not intuitive.
Fixes: 1071a8358a ("ice: Implement virtchnl commands for AVF support")
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Konrad Jankowski <konrad0.jankowski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 5710ab79166504013f7c0ae6a57e7d2fd26e5c43 ]
The i40e_vc_send_msg_to_vf_ex (and its wrapper i40e_vc_send_msg_to_vf)
function has logic to detect "failure" responses sent to the VF. If a VF
is sent more than I40E_DEFAULT_NUM_INVALID_MSGS_ALLOWED, then the VF is
marked as disabled. In either case, a dev_info message is printed
stating that a VF opcode failed.
This logic originates from the early implementation of VF support in
commit 5c3c48ac6b ("i40e: implement virtual device interface").
That commit did not go far enough. The "logic" for this behavior seems
to be that error responses somehow indicate a malicious VF. This is not
really true. The PF might be sending an error for any number of reasons
such as lacking resources, an unsupported operation, etc. This does not
indicate a malicious VF. We already have a separate robust malicious VF
detection which relies on hardware logic to detect and prevent a variety
of behaviors.
There is no justification for this behavior in the original
implementation. In fact, a later commit 18b7af57d9 ("i40e: Lower some
message levels") reduced the opcode failure message from a dev_err to a
dev_info. In addition, recent commit 01cbf50877e6 ("i40e: Fix to not
show opcode msg on unsuccessful VF MAC change") changed the logic to
allow quieting it for expected failures.
That commit prevented this logic from kicking in for specific
circumstances. This change did not go far enough. The behavior is not
documented nor is it part of any requirement for our products. Other
operating systems such as the FreeBSD implementation of our driver do
not include this logic.
It is clear this check does not make sense, and causes problems which
led to ugly workarounds.
Fix this by just removing the entire logic and the need for the
i40e_vc_send_msg_to_vf_ex function.
Fixes: 01cbf50877e6 ("i40e: Fix to not show opcode msg on unsuccessful VF MAC change")
Fixes: 5c3c48ac6b ("i40e: implement virtual device interface")
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Konrad Jankowski <konrad0.jankowski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 2cf29e55894886965722e6625f6a03630b4db31d ]
Modify netdev->features for vlan stripping based on virtual
channel messages received from the PF. Change is needed
to synchronize vlan strip status between PF sysfs and iavf ethtool.
Fixes: 5951a2b9812d ("iavf: Fix VLAN feature flags after VFR")
Signed-off-by: Norbert Ciosek <norbertx.ciosek@intel.com>
Signed-off-by: Michal Maloszewski <michal.maloszewski@intel.com>
Tested-by: Konrad Jankowski <konrad0.jankowski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit bc2f39a6252ee40d9bfc2743d4437d420aec5f6e upstream.
This code was re-organized and there some unlocks missing now.
Fixes: 898ef1cb1cb2 ("iavf: Combine init and watchdog state machines")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Tested-by: Konrad Jankowski <konrad0.jankowski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
