The three-character drain delay was added by commit f1175daa53 ("USB:
ti_usb_3410_5052: kill custom closing_wait") when removing the custom
closing-wait implementation, which used a fixed 20 ms poll period and
drain delay.
This was likely a bit too conservative as a one-character timeout (e.g.
33 ms at 300 bps) should be enough to compensate for the lack of a
transmitter empty bit in the TUSB5052 line-status register.
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
Document that the device line-status register doesn't tell when the
transmitter shift register has emptied and that this is why the
one-character drain delay is needed.
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
The f81232 driver now waits for the transmit FIFO to drain during close
so there is no need to keep the time-based drain delay, which would add
up to two seconds on every close for low line speeds.
Fixes: 98405f8103 ("USB: serial: f81232: add tx_empty function")
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
Peter writes:
Several Cadence3 improvements are introduced in v5.13-rc1:
- Add recovery during resume if the controller was lost power at system suspend
- Reduce DMA memory footprint
- Other small improvements
* tag 'usb-v5.13-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/peter.chen/usb:
usb: cdnsp: Fixes issue with Configure Endpoint command
usb: cdnsp: remove redundant initialization of variable ret
usb: cdns3: delete repeated clear operations
usb: cdns3: Optimize DMA request buffer allocation
usb: cdns3: Use dma_pool_* api to alloc trb pool
usb: cdns3: fix static checker warning.
usb: cdns3: imx: mark cdns_imx_system_resume as __maybe_unused
usb: cdns3: trace: delete the trace parameter for request->trb
usb: cdns3: imx: add power lost support for system resume
usb: cdns3: add power lost support for system resume
Patch adds flag EP_UNCONFIGURED to detect whether endpoint was
unconfigured. This flag is set in cdnsp_reset_device after Reset Device
command. Among others this command disables all non control endpoints.
Flag is used in cdnsp_gadget_ep_disable to protect controller against
invoking Configure Endpoint command on disabled endpoint. Lack of this
protection in some cases caused that Configure Endpoint command completed
with Context State Error code completion.
Fixes: 3d82904559 ("usb: cdnsp: cdns3 Add main part of Cadence USBSSP DRD Driver")
Signed-off-by: Pawel Laszczak <pawell@cadence.com>
Signed-off-by: Peter Chen <peter.chen@kernel.org>
The variable ret is being initialized with a value that is
never read and it is being updated later with a new value. The
initialization is redundant and can be removed.
Addresses-Coverity: ("Unused value")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Reviewed-by: Pawel Laszczak <pawell@cadence.com>
Signed-off-by: Peter Chen <peter.chen@kernel.org>
dma_alloc_coherent() might fail on the platform with a small
DMA region.
To avoid such failure in cdns3_prepare_aligned_request_buf(),
dma_alloc_coherent() is replaced with dma_alloc_noncoherent()
to allocate aligned request buffer of dynamic length.
Reported-by: Aswath Govindraju <a-govindraju@ti.com>
Signed-off-by: Sanket Parmar <sparmar@cadence.com>
Signed-off-by: Peter Chen <peter.chen@kernel.org>
Allocation of DMA coherent memory in atomic context using
dma_alloc_coherent() might fail on platforms with smaller
DMA region.
To fix it, dma_alloc_coherent() is replaced with dma_pool
API to allocate a smaller chunk of DMA coherent memory for
TRB rings.
Reported-by: Aswath Govindraju <a-govindraju@ti.com>
Signed-off-by: Sanket Parmar <sparmar@cadence.com>
Signed-off-by: Peter Chen <peter.chen@kernel.org>
The patch c450e48eb570: "usb: cdns3: add power lost support for
system resume" from Feb 18, 2021, leads to the following static
checker warning:
drivers/usb/cdns3/core.c:551 cdns_resume()
error: uninitialized symbol 'ret'.
drivers/usb/cdns3/core.c
544
545 if (!role_changed) {
546 if (cdns->role == USB_ROLE_HOST)
547 ret = cdns_drd_host_on(cdns);
548 else if (cdns->role == USB_ROLE_DEVICE)
549 ret = cdns_drd_gadget_on(cdns);
"ret" is uninitialized at else branch.
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Frank Li <frank.li@nxp.com>
Signed-off-by: Peter Chen <peter.chen@kernel.org>
The function cdns_imx_system_resume() may have no callers depending
on configuration, so it must be marked __maybe_unused to avoid
harmless warning:
drivers/usb/cdns3/cdns3-imx.c:378:12: warning:
'cdns_imx_system_resume' defined but not used [-Wunused-function]
378 | static int cdns_imx_system_resume(struct device *dev)
| ^~~~~~~~~~~~~~~~~~~~~~
Fixes: 67982dfa59de ("usb: cdns3: imx: add power lost support for system resume")
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Signed-off-by: Peter Chen <peter.chen@kernel.org>
It is not correct using %pa to print virtual address of request->trb, and
it is hard to print its physical address due to the virtual address is
zero before using. It could use index (start_trb/end_trb) to know the
current trb position, so no matter virtual address or physical address
for request-trb is not so meaningful.
Reported-by: Steven Rostedt <rostedt@goodmis.org>
Signed-off-by: Peter Chen <peter.chen@kernel.org>
If the controller lost its power during the system suspend, we need
to do all initialiation operations.
Signed-off-by: Peter Chen <peter.chen@nxp.com>
Signed-off-by: Frank Li <frank.li@nxp.com>
Signed-off-by: Peter Chen <peter.chen@kernel.org>
Add a debug printk to dump the GPIO configuration stored in EEPROM
during probe.
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Johan Hovold <johan@kernel.org>
Use the new GPIO valid-mask feature to inform gpiolib which pins are
available for use instead of handling that in a request callback.
This also allows user space to figure out which pins are available
through the chardev interface without having to request each pin in
turn.
Note that the return value when requesting an unavailable pin will now
be -EINVAL instead of -ENODEV.
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Johan Hovold <johan@kernel.org>
In accordance with the USB HCD/DRD schema all the USB controllers are
supposed to have DT-nodes named with prefix "^usb(@.*)?". Since the
existing DT-nodes will be renamed in a subsequent patch let's fix the DWC3
Qcom-specific code to detect the DWC3 sub-node just by checking its
compatible string to match the "snps,dwc3". The semantic of the code
won't change seeing all the DWC USB3 nodes are supposed to have the
compatible property with any of those strings set.
Signed-off-by: Serge Semin <Sergey.Semin@baikalelectronics.ru>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20210409113029.7144-7-Sergey.Semin@baikalelectronics.ru
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Kunpeng920's EHCI controller does not have SBRN register.
Reading the SBRN register when the controller driver is
initialized will get 0.
When rebooting the EHCI driver, ehci_shutdown() will be called.
if the sbrn flag is 0, ehci_shutdown() will return directly.
The sbrn flag being 0 will cause the EHCI interrupt signal to
not be turned off after reboot. this interrupt that is not closed
will cause an exception to the device sharing the interrupt.
Therefore, the EHCI controller of Kunpeng920 needs to skip
the read operation of the SBRN register.
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Longfang Liu <liulongfang@huawei.com>
Link: https://lore.kernel.org/r/1617958081-17999-1-git-send-email-liulongfang@huawei.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Use the port struct device rather than tty class device for debugging.
Note that while USB serial doesn't support serdev yet (due to serdev not
handling hotplugging), serdev ttys do not have a corresponding class
device and would have been logged using a "(NULL device *):" prefix.
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
TIOCSSERIAL is a horrid, underspecified, legacy interface which for most
serial devices is only useful for setting the close_delay and
closing_wait parameters.
The xmit_fifo_size parameter could be used to set the hardware transmit
fifo size of a legacy UART when it could not be detected, but the
interface is limited to eight bits and should be left unset when it is
not used.
Similarly, baud_base could be used to set the UART base clock when it
could not be detected, but might as well be left unset when it is not
known (which is the case for CDC).
Fix the cdc-acm TIOCGSERIAL implementation by dropping its custom
interpretation of the unused xmit_fifo_size and baud_base fields, which
overflowed the former with the URB buffer size and set the latter to the
current line speed. Also return the port line number, which is the only
other value used besides the close parameters.
Note that the current line speed can still be retrieved through the
standard termios interfaces.
Fixes: 18c75720e6 ("USB: allow users to run setserial with cdc-acm")
Acked-by: Oliver Neukum <oneukum@suse.com>
Signed-off-by: Johan Hovold <johan@kernel.org>
Link: https://lore.kernel.org/r/20210408131602.27956-4-johan@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
TIOCSSERIAL is a horrid, underspecified, legacy interface which for most
serial devices is only useful for setting the close_delay and
closing_wait parameters.
A non-privileged user has only ever been able to set the since long
deprecated ASYNC_SPD flags and trying to change any other *supported*
feature should result in -EPERM being returned. Setting the current
values for any supported features should return success.
Fix the cdc-acm implementation which instead indicated that the
TIOCSSERIAL ioctl was not even implemented when a non-privileged user
set the current values.
Fixes: ba2d8ce9db ("cdc-acm: implement TIOCSSERIAL to avoid blocking close(2)")
Acked-by: Oliver Neukum <oneukum@suse.com>
Signed-off-by: Johan Hovold <johan@kernel.org>
Link: https://lore.kernel.org/r/20210408131602.27956-3-johan@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This reverts commit b401f8c4f4.
The offending commit claimed that trying to set the values reported back
by TIOCGSERIAL as a regular user could result in an -EPERM error when HZ
is 250, but that was never the case.
With HZ=250, the default 0.5 second value of close_delay is converted to
125 jiffies when set and is converted back to 50 centiseconds by
TIOCGSERIAL as expected (not 12 cs as was claimed, even if that was the
case before an earlier fix).
Comparing the internal current and new jiffies values is just fine to
determine if the value is about to change so drop the bogus workaround
(which was also backported to stable).
For completeness: With different default values for these parameters or
with a HZ value not divisible by two, the lack of rounding when setting
the default values in tty_port_init() could result in an -EPERM being
returned, but this is hardly something we need to worry about.
Cc: Anthony Mallet <anthony.mallet@laas.fr>
Cc: stable@vger.kernel.org
Acked-by: Oliver Neukum <oneukum@suse.com>
Signed-off-by: Johan Hovold <johan@kernel.org>
Link: https://lore.kernel.org/r/20210408131602.27956-2-johan@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This can be used by Type-C controller drivers which use a standard
usb-connector fwnode, with altmodes sub-node, to describe the available
altmodes.
Note there are is no devicetree bindings documentation for the altmodes
node, this is deliberate. ATM the fwnodes used to register the altmodes
are only used internally to pass platform info from a drivers/platform/x86
driver to the type-c subsystem.
When a devicetree user of this functionally comes up and the dt-bindings
have been hashed out the internal use can be adjusted to match the
dt-bindings.
Currently the typec_port_register_altmodes() function expects
an "altmodes" child fwnode on port->dev with this "altmodes" fwnode having
child fwnodes itself with each child containing 2 integer properties:
1. A "svid" property, which sets the id of the altmode, e.g. displayport
altmode has a svid of 0xff01.
2. A "vdo" property, typically used as a bitmask describing the
capabilities of the altmode, the bits in the vdo are specified in the
specification of the altmode.
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Link: https://lore.kernel.org/r/20210409134033.105834-2-hdegoede@redhat.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
usb_role_switch_find_by_fwnode() returns a reference to the role-switch
which must be put by calling usb_role_switch_put().
usb_role_switch_put() calls module_put(sw->dev.parent->driver->owner),
add a matching try_module_get() to usb_role_switch_find_by_fwnode(),
making it behave the same as the other usb_role_switch functions
which return a reference.
This avoids a WARN_ON being hit at kernel/module.c:1158 due to the
module-refcount going below 0.
Fixes: c6919d5e0c ("usb: roles: Add usb_role_switch_find_by_fwnode()")
Cc: stable <stable@vger.kernel.org>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Link: https://lore.kernel.org/r/20210409124136.65591-1-hdegoede@redhat.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This driver's remove path calls cancel_delayed_work(). However, that
function does not wait until the work function finishes. This means
that the callback function may still be running after the driver's
remove function has finished, which would result in a use-after-free.
Fix by calling cancel_delayed_work_sync(), which ensures that
the work is properly cancelled, no longer running, and unable
to re-schedule itself.
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Link: https://lore.kernel.org/r/20210407092947.3271507-1-yangyingliang@huawei.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
