The write buffer comes from user and should be const.
Constify write buffer in mtd core and across all _write_user_prot_reg()
users. cfi_cmdset_{0001, 0002} and onenand_base will pay the cost of an
explicit cast to discard the const qualifier since the beginning, since
they are using an otp_op_t function prototype that is used for both reads
and writes. mtd_dataflash and SPI NOR will benefit of the const buffer
because they are using different paths for writes and reads.
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20210403060931.7119-1-tudor.ambarus@microchip.com
MTD core:
* Handle possible -EPROBE_DEFER from parse_mtd_partitions()
NAND core:
* Fix error handling in nand_prog_page_op() (x2)
* Add a helper to retrieve the number of ECC bytes per step
* Add a helper to retrieve the number of ECC steps
* Let ECC engines advertize the exact number of steps
* ECC Hamming:
- Populate the public nsteps field
- Use the public nsteps field
* ECC BCH:
- Populate the public nsteps field
- Use the public nsteps field
Raw NAND core:
* Add support for secure regions in NAND memory
* Try not to use the ECC private structures
* Remove duplicate include in rawnand.h
* BBT:
- Skip bad blocks when searching for the BBT in NAND
Raw NAND controller drivers:
* Qcom:
- Convert bindings to YAML
- Use dma_mapping_error() for error check
- Add missing nand_cleanup() in error path
- Return actual error code instead of -ENODEV
- Update last code word register
- Add helper to configure location register
- Rename parameter name in macro
- Add helper to check last code word
- Convert nandc to chip in Read/Write helper
- Update register macro name for 0x2c offset
* GPMI:
- Fix a double free in gpmi_nand_init
* Rockchip:
- Use flexible-array member instead of zero-length array
* Atmel:
- Update ecc_stats.corrected counter
* MXC:
- Remove unneeded of_match_ptr()
* R852:
- replace spin_lock_irqsave by spin_lock in hard IRQ
* Brcmnand:
- Move to polling in pio mode on oops write
- Read/write oob during EDU transfer
- Fix OOB R/W with Hamming ECC
* FSMC:
- Fix error code in fsmc_nand_probe()
* OMAP:
- Use ECC information from the generic structures
SPI-NAND core:
* Add missing MODULE_DEVICE_TABLE()
SPI-NAND drivers:
* gigadevice: Support GD5F1GQ5UExxG
SPI NOR core changes:
- Add OTP support
- Fix module unload while an op in progress
- Add various cleanup patches
SPI NOR controller drivers changes:
- intel-spi: Move platform data header to x86 subfolder
On a typical end product, a vendor may choose to secure some regions in
the NAND memory which are supposed to stay intact between FW upgrades.
The access to those regions will be blocked by a secure element like
Trustzone. So the normal world software like Linux kernel should not
touch these regions (including reading).
The regions are declared using a NAND chip DT property,
"secure-regions". So let's make use of this property in the raw NAND
core and skip access to the secure regions present in a system.
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20210402150128.29128-4-manivannan.sadhasivam@linaro.org
Use the new OTP ops to implement OTP access on Winbond flashes. Most
Winbond flashes provides up to four different OTP regions ("Security
Registers").
Winbond devices use a special opcode to read and write to the OTP
regions, just like the RDSFDP opcode. In fact, it seems that the
(undocumented) first OTP area of the newer flashes is the actual SFDP
table.
On a side note, Winbond devices also allow erasing the OTP regions as
long as the area isn't locked down.
Signed-off-by: Michael Walle <michael@walle.cc>
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Link: https://lore.kernel.org/r/20210321235140.8308-3-michael@walle.cc
This patch introduces the module_mtd_blktrans macro which is a convenience
macro for mtd blktrans modules similar to module_platform_driver.
It is intended to be used by drivers which init/exit section does nothing
but register/unregister the mtd blktrans driver. By using this macro it is
possible to eliminate a few lines of boilerplate code per mtd blktrans
driver.
Signed-off-by: Dejin Zheng <zhengdejin5@gmail.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20210213164600.409061-2-zhengdejin5@gmail.com
The Global Block Unlock command has different names depending
on the manufacturer, but always the same command value: 0x98.
Macronix's MX25U12835F names it Gang Block Unlock, Winbond's
W25Q128FV names it Global Block Unlock and Microchip's
SST26VF064B names it Global Block Protection Unlock.
Used in the Individual Block Protection mode, which is mutually
exclusive with the Block Protection mode (BP0-3).
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Reviewed-by: Pratyush Yadav <p.yadav@ti.com>
Reviewed-by: Michael Walle <michael@walle.cc>
Link: https://lore.kernel.org/r/20210121110546.382633-1-tudor.ambarus@microchip.com
SPI NOR core changes:
- Initial support for stateful Octal DTR mode using volatile settings
- Preliminary support for JEDEC 251 (xSPI) and JEDEC 216D standards
- Support for Cypress Semper flash
- Support to specify ECC block size of SPI NOR flashes
- Fixes to avoid clearing of non-volatile Block Protection bits at probe
Generic NAND core:
* ECC management:
- Add an I/O request tweaking mechanism
- Entire rework of the software BCH ECC driver, creation of a real
ECC engine, getting rid of raw NAND structures, migration to more
generic prototypes, misc fixes and style cleanup. Moved now to the
Generic NAND layer.
- Entire rework of the software Hamming ECC driver, creation of a
real ECC engine, getting rid of raw NAND structures, misc renames,
comment updates, cleanup, and style fixes. Moved now to the
generic NAND layer.
- Necessary plumbing at the NAND level to retrieve generic NAND ECC
engines (softwares and on-die).
- Update of the bindings.
Raw NAND core:
* Geting rid of the chip->ecc.priv entry.
* Fix miscellaneous typos in kernel-doc
Raw NAND controller drivers:
* AU1550: Ensure the presence of the right includes
* Davinci: Do not use extra dereferencing
* GPMI:
- Fix the driver only sense CS0 R/B issue
- Fix the random DMA timeout issue
- Use a single line for of_device_id
- Use of_device_get_match_data()
- Fix reference count leak in gpmi ops
- Cleanup makefile
- Fix binding matching of clocks on different SoCs
* Ingenic: remove redundant get_device() in ingenic_ecc_get()
* Intel LGM: New NAND controller driver
* Marvell: Drop useless line
* Meson:
- Fix a resource leak in init
- Fix meson_nfc_dma_buffer_release() arguments
* mxc:
- Use device_get_match_data()
- Use a single line for of_device_id
- Remove platform data support
* Qcom:
- Add support for SDX55
- Support for IPQ6018 QPIC NAND controller
- Fix DMA sync on FLASH_STATUS register read
* Rockchip: New NAND controller driver for RK3308, RK2928 and others
* Sunxi: Add MDMA support
SPI-NAND core:
* Creation of a SPI-NAND on-die ECC engine
* Move ECC related definitions earlier in the driver
* Fix typo in comment
* Fill a default ECC provider/algorithm
* Remove outdated comment
* Fix OOB read
* Allow the case where there is no ECC engine
* Use the external ECC engine logic
SPI-NAND chip drivers:
* Micron:
- Add support for MT29F2G01AAAED
- Use more specific names
* Macronix:
- Add support for MX35LFxG24AD
- Add support for MX35LFxGE4AD
Others:
* onenand: Use mtd->oops_panic_write as condition
* plat-ram: correctly free memory on error path in platram_probe()
Add the logic in the NAND core to find the right ECC engine depending
on the NAND chip requirements and the user desires. Right now, the
choice may be made between (more will come):
* software Hamming
* software BCH
* on-die (SPI-NAND devices only)
Once the ECC engine has been found, the ECC engine must be
configured.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20201001102014.20100-2-miquel.raynal@bootlin.com
Let's continue introducing the generic ECC engine abstraction in the
NAND subsystem by instantiating a first ECC engine: the software
BCH one.
While at it, make a very tidy ecc_sw_bch_init() function and move all
the sanity checks and user input management in
nand_ecc_sw_bch_init_ctx(). This second helper will be called from the
raw RAND core.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20200929230124.31491-10-miquel.raynal@bootlin.com
These functions must be usable by the main NAND core, so their names
must be technology-agnostic as well as the parameters. Hence, we pass
a generic nand_device instead of a raw nand_chip structure.
As it seems that changing the raw NAND functions to always pass a
generic NAND device is a lost of time, we prefer to create dedicated
raw NAND wrappers that will be useful in the near future to do the
translation.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20200929230124.31491-8-miquel.raynal@bootlin.com
Currently, BCH and Hamming engine are sharing the same
tweaking/restoring I/O mechanism: they need the I/O request to fully
cover the main/OOB area. Let's make this code generic as sharing the
code between two drivers is already a win. Maybe other ECC engine
drivers will need it too.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20200929230124.31491-2-miquel.raynal@bootlin.com
Perform a Soft Reset on shutdown on flashes that support it so that the
flash can be reset to its initial state and any configurations made by
spi-nor (given that they're only done in volatile registers) will be
reset. This will hand back the flash in pristine state for any further
operations on it.
Signed-off-by: Pratyush Yadav <p.yadav@ti.com>
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Reviewed-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Link: https://lore.kernel.org/r/20201005153138.6437-13-p.yadav@ti.com
Double Transfer Rate (DTR) is SPI protocol in which data is transferred
on each clock edge as opposed to on each clock cycle. Make
framework-level changes to allow supporting flashes in DTR mode.
Right now, mixed DTR modes are not supported. So, for example a mode
like 4S-4D-4D will not work. All phases need to be either DTR or STR.
The xSPI spec says that "The program commands provide SPI backward
compatible commands for programming data...". So 8D-8D-8D page program
opcodes are populated with using 1S-1S-1S opcodes.
Signed-off-by: Pratyush Yadav <p.yadav@ti.com>
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Reviewed-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Link: https://lore.kernel.org/r/20201005153138.6437-4-p.yadav@ti.com
NAND core changes:
* Use the new generic ECC object
* Create helpers to set/extract the ECC requirements
* Create a helper to extract the ECC configuration
* Add a NAND page I/O request type
* Introduce the ECC engine framework
Raw NAND core changes:
* Don't overwrite the error code from nand_set_ecc_soft_ops()
* Introduce nand_set_ecc_on_host_ops()
* Use the NAND framework user_conf object for ECC flags
* Use the ECC framework user input parsing bits
* Use the ECC framework nand_ecc_is_strong_enough() helper
* Use the ECC framework OOB layouts
* Make use of the ECC framework
* Use nanddev_get/set_ecc_requirements() when relevant
* Use the new ECC engine type enumeration
* Separate the ECC engine type and the ECC byte placement
* Move the nand_ecc_algo enum to the generic NAND layer
* Rename the ECC algorithm enumeration items
* Add a kernel doc to the ECC algorithm enumeration
* DT bindings:
- Document boolean NAND ECC properties
- Document nand-ecc-engine
- Document nand-ecc-placement
Raw NAND drivers changes:
* Ams-Delta: Fix non-OF build warning
* Atmel:
- Check return values for nand_read_data_op
- Simplify with dev_err_probe()
- Get rid of the legacy interface implementation
- Convert the driver to exec_op()
- Use nand_prog_page_end_op()
- Use nand_{write,read}_data_op()
- Drop redundant nand_read_page_op()
- Enable the NFC controller at probe time
- Disable clk on error handling path in probe
* Cadence: remove a redundant dev_err call
* Gpmi:
- Simplify with dev_err_probe()
* Marvell:
- Fix and update kerneldoc
- Simplify with dev_err_probe()
- Fix and update kerneldoc
- Simplify with dev_err_probe()
- Support panic_write for mtdoops
* Onenand:
- Simplify the return expression of onenand_transfer_auto_oob
- Simplify with dev_err_probe()
* Oxnas: cleanup/simplify code
* Pasemi: Make pasemi_device_ready() static
* Qcom: Simplify with dev_err_probe()
* Stm32_fmc2: fix a buffer overflow
* Vf610: Remove unused function vf610_nfc_transfer_size()
SPI-NAND changes:
* Use nanddev_get_ecc_conf() when relevant
* Gigadevice:
- Add support for GD5F4GQ4xC
- Add QE Bit
- Use only one dummy byte in QUADIO
* Macronix:
- Add support for MX31UF1GE4BC
- Add support for MX31LF1GE4BC
