[ Upstream commit 2667f6b7af99e81958fa97c03bb519fcb09d0055 ]
I have a ST1633 touch controller which fails to probe due to a timeout
waiting for the controller to become ready. Increasing the minimum
delay to 100ms ensures that the probe sequence completes successfully.
The ST1633 datasheet says nothing about the maximum delay here and the
ST1232 I2C protocol document says "wait until" with no notion of a
timeout.
Since this only runs once during probe, being generous with the timout
seems reasonable and most likely the device will become ready
eventually.
(It may be worth noting that I saw this issue with a PREEMPT_RT patched
kernel which probably has tighter wakeups from usleep_range() than other
preemption models.)
Fixes: f605be6a57 ("Input: st1232 - wait until device is ready before reading resolution")
Signed-off-by: John Keeping <john@metanate.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/20210929152609.2421483-1-john@metanate.com
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 5c4c2c8e6fac26fa0b80c234d6e9f75d637193af ]
Currently autoloading for SPI devices does not use the DT ID table, it uses
SPI modalises. Supporting OF modalises is going to be difficult if not
impractical, an attempt was made but has been reverted, so ensure that
module autoloading works for this driver by adding a SPI device ID table.
Fixes: 96c8395e21 ("spi: Revert modalias changes")
Signed-off-by: Mark Brown <broonie@kernel.org>
Link: https://lore.kernel.org/r/20210927134104.38648-1-broonie@kernel.org
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Pull input fixes from Dmitry Torokhov:
- a new product ID for the xpad joystick driver
- fixes to resistive-adc-touch and snvs_pwrkey drivers
- a change to touchscreen helpers to make clang happier
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input:
Input: touchscreen - avoid bitwise vs logical OR warning
Input: xpad - add support for another USB ID of Nacon GC-100
Input: resistive-adc-touch - fix division by zero error on z1 == 0
Input: snvs_pwrkey - add clk handling
A new warning in clang points out a few places in this driver where a
bitwise OR is being used with boolean types:
drivers/input/touchscreen.c:81:17: warning: use of bitwise '|' with boolean operands [-Wbitwise-instead-of-logical]
data_present = touchscreen_get_prop_u32(dev, "touchscreen-min-x",
^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
This use of a bitwise OR is intentional, as bitwise operations do not
short circuit, which allows all the calls to touchscreen_get_prop_u32()
to happen so that the last parameter is initialized while coalescing the
results of the calls to make a decision after they are all evaluated.
To make this clearer to the compiler, use the '|=' operator to assign
the result of each touchscreen_get_prop_u32() call to data_present,
which keeps the meaning of the code the same but makes it obvious that
every one of these calls is expected to happen.
Signed-off-by: Nathan Chancellor <nathan@kernel.org>
Reported-by: Nick Desaulniers <ndesaulniers@google.com>
Reviewed-by: Nick Desaulniers <ndesaulniers@google.com>
Link: https://lore.kernel.org/r/20211014205757.3474635-1-nathan@kernel.org
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
On i.MX7S and i.MX8M* (but not i.MX6*) the pwrkey device has an
associated clock. Accessing the registers requires that this clock is
enabled. Binding the driver on at least i.MX7S and i.MX8MP while not
having the clock enabled results in a complete hang of the machine.
(This usually only happens if snvs_pwrkey is built as a module and the
rtc-snvs driver isn't already bound because at bootup the required clk
is on and only gets disabled when the clk framework disables unused clks
late during boot.)
This completes the fix in commit 135be16d35 ("ARM: dts: imx7s: add
snvs clock to pwrkey").
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Link: https://lore.kernel.org/r/20211013062848.2667192-1-u.kleine-koenig@pengutronix.de
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Pull input updates from Dmitry Torokhov:
- several device tree bindings for input devices have been converted to
yaml
- dropped no longer used ixp4xx-beeper and CSR Prima2 PWRC drivers
- analog joystick has been converted to use ktime API and no longer
warn about low resolution timers
- a few driver fixes
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input: (24 commits)
Input: analog - always use ktime functions
Input: mms114 - support MMS134S
Input: elan_i2c - reduce the resume time for controller in Whitebox
Input: edt-ft5x06 - added case for EDT EP0110M09
Input: adc-keys - drop bogus __refdata annotation
Input: Fix spelling mistake in Kconfig "useable" -> "usable"
Input: Fix spelling mistake in Kconfig "Modul" -> "Module"
Input: remove dead CSR Prima2 PWRC driver
Input: adp5589-keys - use the right header
Input: adp5588-keys - use the right header
dt-bindings: input: tsc2005: Convert to YAML schema
Input: ep93xx_keypad - prepare clock before using it
dt-bindings: input: sun4i-lradc: Add wakeup-source
dt-bindings: input: Convert Regulator Haptic binding to a schema
dt-bindings: input: Convert Pixcir Touchscreen binding to a schema
dt-bindings: input: Convert ChipOne ICN8318 binding to a schema
Input: pm8941-pwrkey - fix comma vs semicolon issue
dt-bindings: power: reset: qcom-pon: Convert qcom PON binding to yaml
dt-bindings: input: pm8941-pwrkey: Convert pm8941 power key binding to yaml
dt-bindings: power: reset: Change 'additionalProperties' to true
...
m68k, mips, s390, and sparc allmodconfig images fail to build with the
following error.
drivers/input/joystick/analog.c:160:2: error:
#warning Precise timer not defined for this architecture.
Remove architecture specific time handling code and always use ktime
functions to determine time deltas. Also remove the now useless use_ktime
kernel parameter.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Randy Dunlap <rdunlap@infradead.org> # build-tested
Link: https://lore.kernel.org/r/20210907123734.21520-1-linux@roeck-us.net
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Pull parisc architecture updates from Helge Deller:
- Fix a kernel crash when a signal is delivered to bad userspace stack
- Fix fall-through warnings in math-emu code
- Increase size of gcc stack frame check
- Switch coding from 'pci_' to 'dma_' API
- Make struct parisc_driver::remove() return void
- Some parisc related Makefile changes
- Minor cleanups, e.g. change to octal permissions, fix macro
collisions, fix PMD_ORDER collision, replace spaces with tabs
* tag 'for-5.15/parisc' of git://git.kernel.org/pub/scm/linux/kernel/git/deller/parisc-linux:
parisc: math-emu: Fix fall-through warnings
parisc: fix crash with signals and alloca
parisc: Fix compile failure when building 64-bit kernel natively
parisc: ccio-dma.c: Added tab instead of spaces
parisc/parport_gsc: switch from 'pci_' to 'dma_' API
parisc: move core-y in arch/parisc/Makefile to arch/parisc/Kbuild
parisc: switch from 'pci_' to 'dma_' API
parisc: Make struct parisc_driver::remove() return void
parisc: remove unused arch/parisc/boot/install.sh and its phony target
parisc: Rename PMD_ORDER to PMD_TABLE_ORDER
parisc: math-emu: Avoid "fmt" macro collision
parisc: Increase size of gcc stack frame check
parisc: Replace symbolic permissions with octal permissions
The caller of this function (parisc_driver_remove() in
arch/parisc/kernel/drivers.c) ignores the return value, so better don't
return any value at all to not wake wrong expectations in driver authors.
The only function that could return a non-zero value before was
ipmi_parisc_remove() which returns the return value of
ipmi_si_remove_by_dev(). Make this function return void, too, as for all
other callers the value is ignored, too.
Also fold in a small checkpatch fix for:
WARNING: Unnecessary space before function pointer arguments
+ void (*remove) (struct parisc_device *dev);
Acked-by: Dmitry Torokhov <dmitry.torokhov@gmail.com> (for drivers/input)
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Acked-by: Sudip Mukherjee <sudipm.mukherjee@gmail.com>
Acked-by: Jiri Slaby <jirislaby@kernel.org>
Signed-off-by: Helge Deller <deller@gmx.de>
This reverts commit 81c7c0a350. The idea
to make write method mandatory was flawed as several client drivers
(such as atkbd) check for presence of write() method to adjust behavior
of the driver.
Reported-by: Nathan Chancellor <nathan@kernel.org>
Reported-by: Michael Kelley <mikelley@microsoft.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Pull UML updates from Richard Weinberger:
- Support for optimized routines based on the host CPU
- Support for PCI via virtio
- Various fixes
* tag 'for-linus-5.14-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rw/uml:
um: remove unneeded semicolon in um_arch.c
um: Remove the repeated declaration
um: fix error return code in winch_tramp()
um: fix error return code in slip_open()
um: Fix stack pointer alignment
um: implement flush_cache_vmap/flush_cache_vunmap
um: add a UML specific futex implementation
um: enable the use of optimized xor routines in UML
um: Add support for host CPU flags and alignment
um: allow not setting extra rpaths in the linux binary
um: virtio/pci: enable suspend/resume
um: add PCI over virtio emulation driver
um: irqs: allow invoking time-travel handler multiple times
um: time-travel/signals: fix ndelay() in interrupt
um: expose time-travel mode to userspace side
um: export signals_enabled directly
um: remove unused smp_sigio_handler() declaration
lib: add iomem emulation (logic_iomem)
um: allow disabling NO_IOMEM
Pull more fallthrough fixes from Gustavo Silva:
"Fix maore fall-through warnings when building the kernel with clang
and '-Wimplicit-fallthrough'"
* tag 'Wimplicit-fallthrough-clang-5.14-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gustavoars/linux:
Input: Fix fall-through warning for Clang
scsi: aic94xx: Fix fall-through warning for Clang
i3c: master: cdns: Fix fall-through warning for Clang
net/mlx4: Fix fall-through warning for Clang
In preparation to enable -Wimplicit-fallthrough for Clang, fix a
warning by explicitly adding a fallthrough; statement.
Notice that this seems to be a Duff device for performance[1]. So,
although the code looks a bit _funny_, I didn't want to refactor
or modify it beyond merely adding a fallthrough marking, which
might be the least disruptive way to fix this issue.
[1] https://www.drdobbs.com/a-reusable-duff-device/184406208
Link: https://github.com/KSPP/linux/issues/115
Signed-off-by: Gustavo A. R. Silva <gustavoars@kernel.org>
Pull tty / serial updates from Greg KH:
"Here is the big set of tty and serial driver patches for 5.14-rc1.
A bit more than normal, but nothing major, lots of cleanups.
Highlights are:
- lots of tty api cleanups and mxser driver cleanups from Jiri
- build warning fixes
- various serial driver updates
- coding style cleanups
- various tty driver minor fixes and updates
- removal of broken and disable r3964 line discipline (finally!)
All of these have been in linux-next for a while with no reported
issues"
* tag 'tty-5.14-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty: (227 commits)
serial: mvebu-uart: remove unused member nb from struct mvebu_uart
arm64: dts: marvell: armada-37xx: Fix reg for standard variant of UART
dt-bindings: mvebu-uart: fix documentation
serial: mvebu-uart: correctly calculate minimal possible baudrate
serial: mvebu-uart: do not allow changing baudrate when uartclk is not available
serial: mvebu-uart: fix calculation of clock divisor
tty: make linux/tty_flip.h self-contained
serial: Prefer unsigned int to bare use of unsigned
serial: 8250: 8250_omap: Fix possible interrupt storm on K3 SoCs
serial: qcom_geni_serial: use DT aliases according to DT bindings
Revert "tty: serial: Add UART driver for Cortina-Access platform"
tty: serial: Add UART driver for Cortina-Access platform
MAINTAINERS: add me back as mxser maintainer
mxser: Documentation, fix typos
mxser: Documentation, make the docs up-to-date
mxser: Documentation, remove traces of callout device
mxser: introduce mxser_16550A_or_MUST helper
mxser: rename flags to old_speed in mxser_set_serial_info
mxser: use port variable in mxser_set_serial_info
mxser: access info->MCR under info->slock
...
Pull input updates from Dmitry Torokhov:
- a new driver for SparkFun Qwiic Joystick
- pm8941-pwrkey driver now supports PMK8350
- a bunch of assorted driver fixes
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input: (44 commits)
Input: joydev - prevent use of not validated data in JSIOCSBTNMAP ioctl
Input: hideep - fix the uninitialized use in hideep_nvm_unlock()
Input: trackpoint - use kobj_to_dev()
Input: atkbd - use kobj_to_dev()
Input: tsc200x-core - use kobj_to_dev()
Input: ims-pcu - use kobj_to_dev()
Input: cros_ec_keyb - use kobj_to_dev() API
dt-bindings: input: touchscreen: st1232: Convert to json-schema
Input: i8042 - fix typos in comments
Input: add SparkFun Qwiic Joystick driver
dt-bindings: Add vendor prefix and bindings for Qwiic Joystick
Input: cy8ctmg110_ts - switch to using gpiod API
Input: cy8ctmg110_ts - switch to using managed resources
Input: cy8ctmg110_ts - use endian helpers when converting data on wire
Input: cy8ctmg110_ts - let I2C core configure wake interrupt
Input: cy8ctmg110_ts - do not hardcode as wakeup source
Input: cy8ctmg110_ts - do not hard code interrupt trigger
Input: cy8ctmg110_ts - rely on platform code to supply interrupt
Input: resistive-adc-touch - fix uninitialized variable 'press'
Input: pm8941-pwrkey - add support for PMK8350 PON_HLOS PMIC peripheral
...
Even though we validate user-provided inputs we then traverse past
validated data when applying the new map. The issue was originally
discovered by Murray McAllister with this simple POC (if the following
is executed by an unprivileged user it will instantly panic the system):
int main(void) {
int fd, ret;
unsigned int buffer[10000];
fd = open("/dev/input/js0", O_RDONLY);
if (fd == -1)
printf("Error opening file\n");
ret = ioctl(fd, JSIOCSBTNMAP & ~IOCSIZE_MASK, &buffer);
printf("%d\n", ret);
}
The solution is to traverse internal buffer which is guaranteed to only
contain valid date when constructing the map.
Fixes: 182d679b22 ("Input: joydev - prevent potential read overflow in ioctl")
Fixes: 999b874f4a ("Input: joydev - validate axis/button maps before clobbering current ones")
Reported-by: Murray McAllister <murray.mcallister@gmail.com>
Suggested-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Alexander Larkin <avlarkin82@gmail.com>
Link: https://lore.kernel.org/r/20210620120030.1513655-1-avlarkin82@gmail.com
Cc: stable@vger.kernel.org
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Pull x86 platform driver updates from Hans de Goede:
"Highlights:
- New think-lmi driver adding support for changing Lenovo Thinkpad
BIOS settings from within Linux using the standard firmware-
attributes class sysfs API
- MS Surface aggregator-cdev now also supports forwarding events to
user-space (for debugging / new driver development purposes only)
- New intel_skl_int3472 driver this provides the necessary glue to
translate ACPI table information to GPIOs, regulators, etc. for
camera sensors on Intel devices with IPU3 attached MIPI cameras
- A whole bunch of other fixes + device-specific quirk additions
- New devm_work_autocancel() devm-helpers.h function"
* tag 'platform-drivers-x86-v5.14-1' of git://git.kernel.org/pub/scm/linux/kernel/git/pdx86/platform-drivers-x86: (83 commits)
platform/x86: dell-wmi-sysman: Change user experience when Admin/System Password is modified
platform/x86: intel_skl_int3472: Uninitialized variable in skl_int3472_handle_gpio_resources()
platform/x86: think-lmi: Move kfree(setting->possible_values) to tlmi_attr_setting_release()
platform/x86: think-lmi: Split current_value to reflect only the value
platform/x86: think-lmi: Fix issues with duplicate attributes
platform/x86: think-lmi: Return EINVAL when kbdlang gets set to a 0 length string
platform/x86: intel_cht_int33fe: Move to its own subfolder
platform/x86: intel_skl_int3472: Move to intel/ subfolder
platform/x86: intel_skl_int3472: Provide skl_int3472_unregister_clock()
platform/x86: intel_skl_int3472: Provide skl_int3472_unregister_regulator()
platform/x86: intel_skl_int3472: Use ACPI GPIO resource directly
platform/x86: intel_skl_int3472: Fix dependencies (drop CLKDEV_LOOKUP)
platform/x86: intel_skl_int3472: Free ACPI device resources after use
platform/x86: Remove "default n" entries
platform/x86: ISST: Use numa node id for cpu pci dev mapping
platform/x86: ISST: Optimize CPU to PCI device mapping
tools/power/x86/intel-speed-select: v1.10 release
tools/power/x86/intel-speed-select: Fix uncore memory frequency display
extcon: extcon-max8997: Simplify driver using devm
extcon: extcon-max8997: Fix IRQ freeing at error path
...
Inside function hideep_nvm_unlock(), variable "unmask_code" could
be uninitialized if hideep_pgm_r_reg() returns error, however, it
is used in the later if statement after an "and" operation, which
is potentially unsafe.
Signed-off-by: Yizhuo <yzhai003@ucr.edu>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
