Merge tag 'arm-soc/for-5.5/devicetree-part2' of https://github.com/Broadcom/stblinux into arm/fixes

This pull request contains the second batch of changes for Broadcom
ARM-based SoCs, please pull the following:

- Nicolas declares a CMA area within the first 1GB of DRAM in order for
  it to be guaranteed to reside there, otherwise ARM64's memory
  initialization will pick up a CMA area within ZONE_DMA32

- Stefan adds the Device Tree node for the built-in Ethernet controller
  (GENET) on the Raspberry Pi 4 model B board

* tag 'arm-soc/for-5.5/devicetree-part2' of https://github.com/Broadcom/stblinux:
  ARM: dts: bcm2711-rpi-4: Enable GENET support
  ARM: dts: bcm2711: force CMA into first GB of memory

Link: https://lore.kernel.org/r/20191118182931.11884-1-f.fainelli@gmail.com
Signed-off-by: Olof Johansson <olof@lixom.net>

arch/arm/boot/dts/bcm2711-rpi-4-b.dts

@@ -19,6 +19,10 @@
 		reg = <0 0 0>;
 	};
 
+	aliases {
+		ethernet0 = &genet;
+	};
+
 	leds {
 		act {
 			gpios = <&gpio 42 GPIO_ACTIVE_HIGH>;
@@ -97,6 +101,19 @@
 	status = "okay";
 };
 
+&genet {
+	phy-handle = <&phy1>;
+	phy-mode = "rgmii-rxid";
+	status = "okay";
+};
+
+&genet_mdio {
+	phy1: ethernet-phy@1 {
+		/* No PHY interrupt */
+		reg = <0x1>;
+	};
+};
+
 /* uart0 communicates with the BT module */
 &uart0 {
 	pinctrl-names = "default";

arch/arm/boot/dts/bcm2711.dtsi

@@ -12,6 +12,26 @@
 
 	interrupt-parent = <&gicv2>;
 
+	reserved-memory {
+		#address-cells = <2>;
+		#size-cells = <1>;
+		ranges;
+
+		/*
+		 * arm64 reserves the CMA by default somewhere in ZONE_DMA32,
+		 * that's not good enough for the BCM2711 as some devices can
+		 * only address the lower 1G of memory (ZONE_DMA).
+		 */
+		linux,cma {
+			compatible = "shared-dma-pool";
+			size = <0x2000000>; /* 32MB */
+			alloc-ranges = <0x0 0x00000000 0x40000000>;
+			reusable;
+			linux,cma-default;
+		};
+	};
+
+
 	soc {
 		/*
 		 * Defined ranges:
@@ -305,6 +325,32 @@
 			cpu-release-addr = <0x0 0x000000f0>;
 		};
 	};
+
+	scb {
+		compatible = "simple-bus";
+		#address-cells = <2>;
+		#size-cells = <1>;
+
+		ranges = <0x0 0x7c000000  0x0 0xfc000000  0x03800000>;
+
+		genet: ethernet@7d580000 {
+			compatible = "brcm,bcm2711-genet-v5";
+			reg = <0x0 0x7d580000 0x10000>;
+			#address-cells = <0x1>;
+			#size-cells = <0x1>;
+			interrupts = <GIC_SPI 157 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 158 IRQ_TYPE_LEVEL_HIGH>;
+			status = "disabled";
+
+			genet_mdio: mdio@e14 {
+				compatible = "brcm,genet-mdio-v5";
+				reg = <0xe14 0x8>;
+				reg-names = "mdio";
+				#address-cells = <0x0>;
+				#size-cells = <0x1>;
+			};
+		};
+	};
 };
 
 &clk_osc {