Pull networking updates from David Miller:
1) Allow setting bluetooth L2CAP modes via socket option, from Luiz
Augusto von Dentz.
2) Add GSO partial support to igc, from Sasha Neftin.
3) Several cleanups and improvements to r8169 from Heiner Kallweit.
4) Add IF_OPER_TESTING link state and use it when ethtool triggers a
device self-test. From Andrew Lunn.
5) Start moving away from custom driver versions, use the globally
defined kernel version instead, from Leon Romanovsky.
6) Support GRO vis gro_cells in DSA layer, from Alexander Lobakin.
7) Allow hard IRQ deferral during NAPI, from Eric Dumazet.
8) Add sriov and vf support to hinic, from Luo bin.
9) Support Media Redundancy Protocol (MRP) in the bridging code, from
Horatiu Vultur.
10) Support netmap in the nft_nat code, from Pablo Neira Ayuso.
11) Allow UDPv6 encapsulation of ESP in the ipsec code, from Sabrina
Dubroca. Also add ipv6 support for espintcp.
12) Lots of ReST conversions of the networking documentation, from Mauro
Carvalho Chehab.
13) Support configuration of ethtool rxnfc flows in bcmgenet driver,
from Doug Berger.
14) Allow to dump cgroup id and filter by it in inet_diag code, from
Dmitry Yakunin.
15) Add infrastructure to export netlink attribute policies to
userspace, from Johannes Berg.
16) Several optimizations to sch_fq scheduler, from Eric Dumazet.
17) Fallback to the default qdisc if qdisc init fails because otherwise
a packet scheduler init failure will make a device inoperative. From
Jesper Dangaard Brouer.
18) Several RISCV bpf jit optimizations, from Luke Nelson.
19) Correct the return type of the ->ndo_start_xmit() method in several
drivers, it's netdev_tx_t but many drivers were using
'int'. From Yunjian Wang.
20) Add an ethtool interface for PHY master/slave config, from Oleksij
Rempel.
21) Add BPF iterators, from Yonghang Song.
22) Add cable test infrastructure, including ethool interfaces, from
Andrew Lunn. Marvell PHY driver is the first to support this
facility.
23) Remove zero-length arrays all over, from Gustavo A. R. Silva.
24) Calculate and maintain an explicit frame size in XDP, from Jesper
Dangaard Brouer.
25) Add CAP_BPF, from Alexei Starovoitov.
26) Support terse dumps in the packet scheduler, from Vlad Buslov.
27) Support XDP_TX bulking in dpaa2 driver, from Ioana Ciornei.
28) Add devm_register_netdev(), from Bartosz Golaszewski.
29) Minimize qdisc resets, from Cong Wang.
30) Get rid of kernel_getsockopt and kernel_setsockopt in order to
eliminate set_fs/get_fs calls. From Christoph Hellwig.
* git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net-next: (2517 commits)
selftests: net: ip_defrag: ignore EPERM
net_failover: fixed rollback in net_failover_open()
Revert "tipc: Fix potential tipc_aead refcnt leak in tipc_crypto_rcv"
Revert "tipc: Fix potential tipc_node refcnt leak in tipc_rcv"
vmxnet3: allow rx flow hash ops only when rss is enabled
hinic: add set_channels ethtool_ops support
selftests/bpf: Add a default $(CXX) value
tools/bpf: Don't use $(COMPILE.c)
bpf, selftests: Use bpf_probe_read_kernel
s390/bpf: Use bcr 0,%0 as tail call nop filler
s390/bpf: Maintain 8-byte stack alignment
selftests/bpf: Fix verifier test
selftests/bpf: Fix sample_cnt shared between two threads
bpf, selftests: Adapt cls_redirect to call csum_level helper
bpf: Add csum_level helper for fixing up csum levels
bpf: Fix up bpf_skb_adjust_room helper's skb csum setting
sfc: add missing annotation for efx_ef10_try_update_nic_stats_vf()
crypto/chtls: IPv6 support for inline TLS
Crypto/chcr: Fixes a coccinile check error
Crypto/chcr: Fixes compilations warnings
...
All macro names for SDIO device IDs are prefixed by vendor name to which
device ID belongs. So for consistency add Broadcom string vendor prefix to
all Cypress macro names as they belong to SDIO Broadcom vendor ID.
Change also Cypress 43012 value from decimal do hexadecimal notation to be
consistent with all other values.
Signed-off-by: Pali Rohár <pali@kernel.org>
Link: https://lore.kernel.org/r/20200522144412.19712-11-pali@kernel.org
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Johannes Berg says:
====================
One batch of changes, containing:
* hwsim improvements from Jouni and myself, to be able to
test more scenarios easily
* some more HE (802.11ax) support
* some initial S1G (sub 1 GHz) work for fractional MHz channels
* some (action) frame registration updates to help DPP support
* along with other various improvements/fixes
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
An incorrect value of use_fwsup is set for 4-way handshake offload for
WPA//WPA2-PSK, caused by commit 3b1e0a7bdf ("brcmfmac: add support for
SAE authentication offload"). It results in missing bit
BRCMF_VIF_STATUS_EAP_SUCCESS set in brcmf_is_linkup() and causes the
failure. This patch correct the value for the case.
Also setting bit BRCMF_VIF_STATUS_EAP_SUCCESS for SAE offload case in
brcmf_is_linkup() to fix SAE offload failure.
Fixes: 3b1e0a7bdf ("brcmfmac: add support for SAE authentication offload")
Signed-off-by: Chung-Hsien Hsu <stanley.hsu@cypress.com>
Signed-off-by: Chi-Hsien Lin <chi-hsien.lin@cypress.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1589277788-119966-1-git-send-email-chi-hsien.lin@cypress.com
In WLAN, priority among various access categories of traffic is
always set by the AP using WMM parameters and this may not always
follow the standard 802.1d priority.
In this change, priority is adjusted based on the AP WMM params
received as part of the Assoc Response and the same is later used
to map the priority of all incoming traffic.
In a specific scenario where EDCA parameters are configured to be same
for all ACs, use the default FW priority definition to avoid queuing
packets of all ACs to the same priority queue.
This change fixes the following 802.11 certification tests:
* 11n - 5.2.31 ACM Bit Conformance test
* 11n - 5.2.32 AC Parameter Modification test
* 11ac - 5.2.33 TXOP Limit test
Signed-off-by: Saravanan Shanmugham <saravanan.shanmugham@cypress.com>
Signed-off-by: Justin Li <justin.li@cypress.com>
Signed-off-by: Madhan Mohan R <madhanmohan.r@cypress.com>
Signed-off-by: Chi-hsien Lin <chi-hsien.lin@cypress.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1588661487-21884-2-git-send-email-chi-hsien.lin@cypress.com
Kalle Valo says:
====================
wireless-drivers-next patches for v5.8
First set of patches for v5.8. Changes all over, ath10k apparently
seeing most new features this time. rtw88 also had lots of changes due
to preparation for new hardware support.
In this pull request there's also a new macro to include/linux/iopoll:
read_poll_timeout_atomic(). This is needed by rtw88 for atomic
polling.
Major changes:
ath11k
* add debugfs file for testing ADDBA and DELBA
* add 802.11 encapsulation offload on hardware support
* add htt_peer_stats_reset debugfs file
ath10k
* enable VHT160 and VHT80+80 modes
* enable radar detection in secondary segment
* sdio: disable TX complete indication to improve throughput
* sdio: decrease power consumption
* sdio: add HTT TX bundle support to increase throughput
* sdio: add rx bitrate reporting
ath9k
* improvements to AR9002 calibration logic
carl9170
* remove buggy P2P_GO support
p54usb
* add support for AirVasT USB stick
rtw88
* add support for antenna configuration
ti wlcore
* add support for AES_CMAC cipher
iwlwifi
* support for a few new FW API versions
* new hw configs
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
It was observed that P2P Cert. 5.1.19: DEVUT responds to Service
Discovery request failed due to DUT did not send GAS Comeback Response
after receiving request from test bed P2P peer. To fix this issue,
we need to add P2P Action Frame retry delay to enhance P2P connection
under VSDB and noisy environment, since the peer can be in other
channels under VSDB.
Signed-off-by: Justin Li <Justin.Li@cypress.com>
Signed-off-by: Chi-hsien Lin <chi-hsien.lin@cypress.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1588572453-194663-4-git-send-email-wright.feng@cypress.com
The firmware does not respond ARP request and causes ping failure with
following steps:
1. Bring up interface
ifconfig wlan0 up or start wpa_supplicant
2. Set the IP address
ifconfig wlan0 192.168.100.10
3. Bring down interface or
ifconfig wlan0 down or kill wpa_supplicant
4. Bring up interface again and set the same IP address
5. Connect to AP(192.168.100.1) and ping to AP will be failed.
FMAC clears arp_hostip when bringing down the interface, but not set it
back if setting the same IP address. We are able to see the IP address
in interface info(inconfig wlan0) but the ping still cannot work because
the firmware ARP offload does not respond the ARP request.
Because of that, we remove "arp_hostip_clear" from function
"brcmf_netdev_stop"
Signed-off-by: Wright Feng <wright.feng@cypress.com>
Signed-off-by: Chi-Hsien Lin <chi-hsien.lin@cypress.com>
Reviewed-by: Franky Lin <franky.lin@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1587970803-77700-3-git-send-email-chi-hsien.lin@cypress.com
Almost all drivers below cfg80211 get the API wrong (except for
cfg80211) and are unable to cope with multiple registrations for
the same frame type, which is valid due to the match filter.
This seems to indicate the API is wrong, and we should maintain
the full information in cfg80211 instead of the drivers.
Change the API to no longer inform the driver about individual
registrations and unregistrations, but rather every time about
the entire state of the entire wiphy and single wdev, whenever
it may have changed. This also simplifies the code in cfg80211
as it no longer has to track exactly what was unregistered and
can free things immediately.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Acked-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Reviewed-by: Sergey Matyukevich <sergey.matyukevich.os@quantenna.com>
Link: https://lore.kernel.org/r/20200417124300.f47f3828afc8.I7f81ef59c2c5a340d7075fb3c6d0e08e8aeffe07@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
We add enable dynamic suspend (autosuspend) support in host driver, and
it can let platform cut down idle power consumption.
To support autosuspend feature in host driver, kernel need to be built
with CONFIG_USB_SUSPEND and autosuspend need to be turn on.
And we also replace wowl feature with adding "needs_remote_wakeup", so
that host still can be waken by wireless device.
Signed-off-by: Wright Feng <wright.feng@cypress.com>
Signed-off-by: Chi-Hsien Lin <chi-hsien.lin@cypress.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1585124429-97371-6-git-send-email-chi-hsien.lin@cypress.com
The current codebase makes use of the zero-length array language
extension to the C90 standard, but the preferred mechanism to declare
variable-length types such as these ones is a flexible array member[1][2],
introduced in C99:
struct foo {
int stuff;
struct boo array[];
};
By making use of the mechanism above, we will get a compiler warning
in case the flexible array does not occur last in the structure, which
will help us prevent some kind of undefined behavior bugs from being
inadvertently introduced[3] to the codebase from now on.
Also, notice that, dynamic memory allocations won't be affected by
this change:
"Flexible array members have incomplete type, and so the sizeof operator
may not be applied. As a quirk of the original implementation of
zero-length arrays, sizeof evaluates to zero."[1]
This issue was found with the help of Coccinelle.
[1] https://gcc.gnu.org/onlinedocs/gcc/Zero-Length.html
[2] https://github.com/KSPP/linux/issues/21
[3] commit 7649773293 ("cxgb3/l2t: Fix undefined behaviour")
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Acked-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200225020804.GA9428@embeddedor
With commit 216b44000a ("brcmfmac: Fix use after free in
brcmf_sdio_readframes()") applied, we see locking timeouts in
brcmf_sdio_watchdog_thread().
brcmfmac: brcmf_escan_timeout: timer expired
INFO: task brcmf_wdog/mmc1:621 blocked for more than 120 seconds.
Not tainted 4.19.94-07984-g24ff99a0f713 #1
"echo 0 > /proc/sys/kernel/hung_task_timeout_secs" disables this message.
brcmf_wdog/mmc1 D 0 621 2 0x00000000 last_sleep: 2440793077. last_runnable: 2440766827
[<c0aa1e60>] (__schedule) from [<c0aa2100>] (schedule+0x98/0xc4)
[<c0aa2100>] (schedule) from [<c0853830>] (__mmc_claim_host+0x154/0x274)
[<c0853830>] (__mmc_claim_host) from [<bf10c5b8>] (brcmf_sdio_watchdog_thread+0x1b0/0x1f8 [brcmfmac])
[<bf10c5b8>] (brcmf_sdio_watchdog_thread [brcmfmac]) from [<c02570b8>] (kthread+0x178/0x180)
In addition to restarting or exiting the loop, it is also necessary to
abort the command and to release the host.
Fixes: 216b44000a ("brcmfmac: Fix use after free in brcmf_sdio_readframes()")
Cc: Dan Carpenter <dan.carpenter@oracle.com>
Cc: Matthias Kaehlcke <mka@chromium.org>
Cc: Brian Norris <briannorris@chromium.org>
Cc: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Acked-by: franky.lin@broadcom.com
Acked-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The 2018 13" MacBook Pro (MacBookPro15,2) has a Broadcom chip, the 4364.
This chip appears to be specific to Apple and is not found in other
hardware.
Add this chip to the brcmfmac driver so that it can be recognized
automatically. Note that the PCI device id is 4464 even though the chip
is referred to as the 4364.
Signed-off-by: brian m. carlson <sandals@crustytoothpaste.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Pull networking updates from David Miller:
1) Add WireGuard
2) Add HE and TWT support to ath11k driver, from John Crispin.
3) Add ESP in TCP encapsulation support, from Sabrina Dubroca.
4) Add variable window congestion control to TIPC, from Jon Maloy.
5) Add BCM84881 PHY driver, from Russell King.
6) Start adding netlink support for ethtool operations, from Michal
Kubecek.
7) Add XDP drop and TX action support to ena driver, from Sameeh
Jubran.
8) Add new ipv4 route notifications so that mlxsw driver does not have
to handle identical routes itself. From Ido Schimmel.
9) Add BPF dynamic program extensions, from Alexei Starovoitov.
10) Support RX and TX timestamping in igc, from Vinicius Costa Gomes.
11) Add support for macsec HW offloading, from Antoine Tenart.
12) Add initial support for MPTCP protocol, from Christoph Paasch,
Matthieu Baerts, Florian Westphal, Peter Krystad, and many others.
13) Add Octeontx2 PF support, from Sunil Goutham, Geetha sowjanya, Linu
Cherian, and others.
* git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net-next: (1469 commits)
net: phy: add default ARCH_BCM_IPROC for MDIO_BCM_IPROC
udp: segment looped gso packets correctly
netem: change mailing list
qed: FW 8.42.2.0 debug features
qed: rt init valid initialization changed
qed: Debug feature: ilt and mdump
qed: FW 8.42.2.0 Add fw overlay feature
qed: FW 8.42.2.0 HSI changes
qed: FW 8.42.2.0 iscsi/fcoe changes
qed: Add abstraction for different hsi values per chip
qed: FW 8.42.2.0 Additional ll2 type
qed: Use dmae to write to widebus registers in fw_funcs
qed: FW 8.42.2.0 Parser offsets modified
qed: FW 8.42.2.0 Queue Manager changes
qed: FW 8.42.2.0 Expose new registers and change windows
qed: FW 8.42.2.0 Internal ram offsets modifications
MAINTAINERS: Add entry for Marvell OcteonTX2 Physical Function driver
Documentation: net: octeontx2: Add RVU HW and drivers overview
octeontx2-pf: ethtool RSS config support
octeontx2-pf: Add basic ethtool support
...
Report monitor interface availability using cfg80211 and support it in
the add_virtual_intf() and del_virtual_intf() callbacks. This new
feature is conditional and depends on firmware flagging monitor packets.
Receiving monitor frames is already handled by the brcmf_netif_mon_rx().
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Move similar/duplicated code out of combination specific code blocks.
This simplifies code a bit and allows adding more combinations later.
A list of combinations remains unchanged.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
