Commit 262f2b53f6 ("brcmfmac: call brcmf_attach() just before calling
brcmf_bus_started()") changed the initialization order of the brcmfmac
SDIO driver. Unfortunately since brcmf_sdiod_intr_register() is now
called before the sdiodev->bus_if initialization, it reads the wrong
chip ID and fails to initialize the GPIO on brcm43362. Thus the chip
cannot send interrupts and fails to probe:
[ 12.517023] brcmfmac: brcmf_sdio_bus_rxctl: resumed on timeout
[ 12.531214] ieee80211 phy0: brcmf_bus_started: failed: -110
[ 12.536976] ieee80211 phy0: brcmf_attach: dongle is not responding: err=-110
[ 12.566467] brcmfmac: brcmf_sdio_firmware_callback: brcmf_attach failed
Initialize the bus interface earlier to ensure that
brcmf_sdiod_intr_register() properly sets up the OOB interrupt.
BugLink: https://bugs.debian.org/cgi-bin/bugreport.cgi?bug=908438
Fixes: 262f2b53f6 ("brcmfmac: call brcmf_attach() just before calling brcmf_bus_started()")
Signed-off-by: Jean-Philippe Brucker <jean-philippe@linaro.org>
Reviewed-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Fixes coccicheck warning:
drivers/net/wireless/broadcom/brcm80211/brcmfmac/fwsignal.c:911:2-24: WARNING: Assignment of 0/1 to bool variable
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: zhengbin <zhengbin13@huawei.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
ioremap has provided non-cached semantics by default since the Linux 2.6
days, so remove the additional ioremap_nocache interface.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Acked-by: Arnd Bergmann <arnd@arndb.de>
NVIDIA Tegra SoCs do not like when OOB wake is enabled and WiFi interface
is in DOWN state during suspend. This results in a CPU hang on programming
OOB wake-up state of the GPIO controller during of system's suspend.
The solution is trivial: don't enable wake for the OOB interrupt when it
should be disabled.
This fixes hang on Tegra20 (Acer A500) and Tegra30 (Nexus 7) devices which
are using BCM4329 and BCM4330 WiFi chips respectively.
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
In the implementation of brcmf_usbdev_qinit() the allocated memory for
reqs is leaking if usb_alloc_urb() fails. Release reqs in the error
handling path.
Fixes: 71bb244ba2 ("brcm80211: fmac: add USB support for bcm43235/6/8 chipsets")
Signed-off-by: Navid Emamdoost <navid.emamdoost@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
With RSDB mode, FMAC and firmware are able to create 2 or more AP,
so we should not set mbss in vif structure if firmware does not
support MBSS feature.
Signed-off-by: Wright Feng <wright.feng@cypress.com>
Signed-off-by: Soeren Moch <smoch@web.de>
Reviewed-by: Chi-Hsien Lin <chi-hsien.lin@cypress.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
With firmware RSDB feature
1. The maximum support interface is four.
2. The maximum difference channel is two.
3. The maximum interfaces of {station/p2p client/AP} are two.
4. The maximum interface of p2p device is one.
Signed-off-by: Wright Feng <wright.feng@cypress.com>
Signed-off-by: Soeren Moch <smoch@web.de>
Reviewed-by: Chi-Hsien Lin <chi-hsien.lin@cypress.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
4359 dongles do not support setting roaming parameters (error -52).
Do not fail the 80211 configuration in this case.
Signed-off-by: Soeren Moch <smoch@web.de>
Acked-by: Chi-Hsien Lin <chi-hsien.lin@cypress.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Newer 4359 chip revisions need a different rambase address.
This fixes firmware download on such devices which fails otherwise.
Signed-off-by: Soeren Moch <smoch@web.de>
Acked-by: Chi-Hsien Lin <chi-hsien.lin@cypress.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Set F2 blocksize to 256 bytes and watermark to 0x40 for 4359. Also
enable and configure F1 MesBusyCtrl. It fixes DMA error while having
UDP bi-directional traffic.
Signed-off-by: Chung-Hsien Hsu <stanley.hsu@cypress.com>
[slightly adapted for rebase on mainline linux]
Signed-off-by: Soeren Moch <smoch@web.de>
Reviewed-by: Chi-Hsien Lin <chi-hsien.lin@cypress.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
There are two D11 cores in RSDB chips like 4359. We have to reset two
D11 cores simutaneously before firmware download, or the firmware may
not be initialized correctly and cause "fw initialized failed" error.
Signed-off-by: Wright Feng <wright.feng@cypress.com>
Signed-off-by: Soeren Moch <smoch@web.de>
Reviewed-by: Chi-Hsien Lin <chi-hsien.lin@cypress.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Make sure to use the current alternate setting when verifying the
interface descriptors to avoid binding to an invalid interface.
Failing to do so could cause the driver to misbehave or trigger a WARN()
in usb_submit_urb() that kernels with panic_on_warn set would choke on.
Fixes: 71bb244ba2 ("brcm80211: fmac: add USB support for bcm43235/6/8 chipsets")
Cc: stable <stable@vger.kernel.org> # 3.4
Cc: Arend van Spriel <arend@broadcom.com>
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
It's important as brcmfmac creates one main interface for each PHY and
doesn't allow deleting it. Not setting carrier could result in other
subsystems misbehaving (e.g. LEDs "netdev" trigger turning LED on).
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The brcmu_pkt_buf_free_skb() function frees "pkt" so it leads to a
static checker warning:
drivers/net/wireless/broadcom/brcm80211/brcmfmac/sdio.c:1974 brcmf_sdio_readframes()
error: dereferencing freed memory 'pkt'
It looks like there was supposed to be a continue after we free "pkt".
Fixes: 4754fceeb9 ("brcmfmac: streamline SDIO read frame routine")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Franky Lin <franky.lin@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
In the implementation of brcmf_p2p_create_p2pdev() the allocated memory
for p2p_vif is leaked when the mac address is the same as primary
interface. To fix this, go to error path to release p2p_vif via
brcmf_free_vif().
Fixes: cb746e4783 ("brcmfmac: check p2pdev mac address uniqueness")
Signed-off-by: Navid Emamdoost <navid.emamdoost@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This fixes a minor WARNING in the cfg80211:
[ 130.658034] ------------[ cut here ]------------
[ 130.662805] WARNING: CPU: 1 PID: 610 at net/wireless/core.c:954 wiphy_unregister+0xb4/0x198 [cfg80211]
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Fixes gcc '-Wunused-but-set-variable' warning:
drivers/net/wireless/broadcom/brcm80211/brcmfmac/chip.c: In function brcmf_chip_dmp_get_regaddr:
drivers/net/wireless/broadcom/brcm80211/brcmfmac/chip.c:790:5: warning: variable mpnum set but not used [-Wunused-but-set-variable]
drivers/net/wireless/broadcom/brcm80211/brcmfmac/chip.c: In function brcmf_chip_dmp_erom_scan:
drivers/net/wireless/broadcom/brcm80211/brcmfmac/chip.c:866:10: warning: variable nsp set but not used [-Wunused-but-set-variable]
drivers/net/wireless/broadcom/brcm80211/brcmfmac/chip.c: In function brcmf_chip_dmp_erom_scan:
drivers/net/wireless/broadcom/brcm80211/brcmfmac/chip.c:866:5: warning: variable nmp set but not used [-Wunused-but-set-variable]
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: zhengbin <zhengbin13@huawei.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
In commit 518a2f1925
("dma-mapping: zero memory returned from dma_alloc_*"),
dma_alloc_coherent has already zeroed the memory.
So memset is not needed.
Signed-off-by: Fuqian Huang <huangfq.daxian@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The firmware may have SAE authentication code built-in. This is
detected by the driver and indicated in the wiphy features flags.
User-space can use this flag to determine whether or not to provide
the password material for SAE authentication in the nl80211 CONNECT
command.
Signed-off-by: Chung-Hsien Hsu <stanley.hsu@cypress.com>
Signed-off-by: Chi-Hsien Lin <chi-hsien.lin@cypress.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
brcmfmac assumed the wifi device always remains powered on and thus
hardcoded the MMC_PM_KEEP_POWER flag expecting the wifi device to
remain on even during suspend/resume cycles.
This is not always the case, some appliances cut power to everything
connected via SDIO for efficiency reasons and this leads to wifi not
being usable after coming out of suspend because the device was not
correctly reinitialized.
So we check for the keep_power capability and if it's not present then
we remove the device and probe it again during resume to mirror what's
happening in hardware and ensure correct reinitialization in the case
when MMC_PM_KEEP_POWER is not supported.
Suggested-by: Gustavo Padovan <gustavo.padovan@collabora.com>
Signed-off-by: Adrian Ratiu <adrian.ratiu@collabora.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
When n_reqs == 0 there is nothing to do so it doesn't make sense to
search for requests and issue a warning because none is found.
Signed-off-by: Martyn Welch <martyn.welch@collabora.com>
Signed-off-by: Adrian Ratiu <adrian.ratiu@collabora.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
With FT-802.1X, driver should send a port authorized event right after
sending a roamed event. It is used to indicate that a new AP is already
authorized so 802.1X is not required.
Acked-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Chung-Hsien Hsu <stanley.hsu@cypress.com>
Signed-off-by: Chi-Hsien Lin <chi-hsien.lin@cypress.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Providing a new wiphy on every PCIe reset was confusing and was causing
configuration problems for some users (supplicant and authenticators).
Sticking to the existing wiphy should make error recovery much simpler
and more reliable.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Acked-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Move code allocating/freeing wiphy out of above functions. This will
allow reinitializing the driver (e.g. on some error) without allocating
a new wiphy.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Acked-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This moves "ops" pointer from "struct brcmf_cfg80211_info" to the
"struct brcmf_pub". This movement makes it possible to allocate wiphy
without attaching cfg80211 (brcmf_cfg80211_attach()). It's required for
later separation of wiphy allocation and driver initialization.
While at it fix also an unlikely memory leak in the brcmf_attach().
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This is a trivial debugfs entry for triggering reset just like in case
of firmware crash. It works by writing 1 to it:
echo 1 > reset
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
In case of compiling driver without DEBUG expose a stub function to make
writing debug code much simpler (no extra conditions). This will allow
e.g. using debugfs_create_file() without any magic if or #ifdef.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Getting RAM info just once per driver's lifetime (during chip
recognition) is not enough as it may get adjusted later (depending on
the used firmware). Subsequent inits may load different firmwares so a
full RAM recognition is required on every PCIe setup. This is especially
important since implementing hardware reset on a firmware crash.
Moreover calling brcmf_chip_get_raminfo() makes sure that RAM core is
up. It's important as having BCMA_CORE_SYS_MEM down on BCM4366 was
resulting in firmware failing to initialize and following error:
[ 65.657546] brcmfmac 0000:01:00.0: brcmf_pcie_download_fw_nvram: Invalid shared RAM address 0x04000001
This change makes brcmf_chip_get_raminfo() call during chip recognition
redundant for PCIe devices but SDIO and USB still need it and it's a
very small overhead anyway.
Fixes: 4684997d9e ("brcmfmac: reset PCIe bus on a firmware crash")
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The strncpy() may truncate the copied string,
replace it by the safer strscpy().
To avoid below compile warning with gcc 8.2:
drivers/net/wireless/broadcom/brcm80211/brcmfmac/cfg80211.c:In function 'brcmf_vndr_ie':
drivers/net/wireless/broadcom/brcm80211/brcmfmac/cfg80211.c:4227:2:
warning: 'strncpy' output truncated before terminating nul copying 3 bytes from a string of the same length [-Wstringop-truncation]
strncpy(iebuf, add_del_cmd, VNDR_IE_CMD_LEN - 1);
^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
Signed-off-by: Xulin Sun <xulin.sun@windriver.com>
Acked-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The pointer hash is being initialized with a value that is never read
and is being re-assigned a little later on. The assignment is
redundant and hence can be removed.
Addresses-Coverity: ("Unused value")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Fixes gcc '-Wunused-but-set-variable' warning:
drivers/net/wireless/broadcom/brcm80211/brcmfmac/cfg80211.c: In function brcmf_update_bss_info:
drivers/net/wireless/broadcom/brcm80211/brcmfmac/cfg80211.c:2962:5: warning: variable dtim_period set but not used [-Wunused-but-set-variable]
drivers/net/wireless/broadcom/brcm80211/brcmfmac/cfg80211.c: In function brcmf_update_bss_info:
drivers/net/wireless/broadcom/brcm80211/brcmfmac/cfg80211.c:2961:6: warning: variable beacon_interval set but not used [-Wunused-but-set-variable]
They are never used so can be removed.
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Firmware crash is a pretty rare event and can't happen too frequently as
it has to be followed by a hardware reinitialization and config reload.
It should be safe to don't use net_ratelimit() when it happens.
For reporting & debugging purposes it's important to provide a complete
log as the last lines are actually the most important. This change
modifies brcmfmac to print all messages in an unlimited way in that
specific case. With this change there should be finally a backtrace of
firmware finally visible after a crash.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Acked-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
When brcmf_detach() from the bus layer upon rmmod we can no longer
communicate. Hence we will set the bus state to DOWN and cleanup
the event and protocol layer. The network interfaces need to be
deleted before brcmf_cfg80211_detach() because the latter does the
wiphy_unregister() which issues a warning if there are still network
devices linked to the wiphy instance.
Reviewed-by: Hante Meuleman <hante.meuleman@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieter-paul.giesberts@broadcom.com>
Reviewed-by: Franky Lin <franky.lin@broadcom.com>
Signed-off-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Tested-by: Rafał Miłecki <rafal@milecki.pl>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The driver has custom regulatory rules which had maximum bandwidth
for 5GHz channels set to 80MHz. As a consequence the driver can
not use 160MHz in AP mode even when the device supports it. So
relax the rules allowing 160MHz. After wiphy_register() the channel
flags are updated according what the device actually supports.
Reviewed-by: Hante Meuleman <hante.meuleman@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieter-paul.giesberts@broadcom.com>
Reviewed-by: Franky Lin <franky.lin@broadcom.com>
Signed-off-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
In my previous commit to validate a policy I neglected to
actually add one to the few drivers using vendor commands,
fix that now.
Reported-by: Tony Lindgren <tony@atomide.com>
Tested-by: Tony Lindgren <tony@atomide.com>
Fixes: 901bb98918 ("nl80211: require and validate vendor command policy")
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Kalle Valu says:
====================
wireless-drivers-next patches for 5.3
First set of patches for 5.3, but not that many patches this time.
This pull request fails to compile with the tip tree due to
ktime_get_boot_ns() API changes there. It should be easy for Linus to
fix it in p54 driver once he pulls this, an example resolution here:
https://lkml.kernel.org/r/20190625160432.533aa140@canb.auug.org.au
Major changes:
airo
* switch to use skcipher interface
p54
* support boottime in scan results
rtw88
* add fast xmit support
* add random mac address on scan support
rt2x00
* add software watchdog to detect hangs, it's disabled by default
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
When Broadcom SDIO cards are idled they go to sleep and a whole
separate subsystem takes over their SDIO communication. This is the
Always-On-Subsystem (AOS) and it can't handle tuning requests.
Specifically, as tested on rk3288-veyron-minnie (which reports having
BCM4354/1 in dmesg), if I force a retune in brcmf_sdio_kso_control()
when "on = 1" (aka we're transition from sleep to wake) by whacking:
bus->sdiodev->func1->card->host->need_retune = 1
...then I can often see tuning fail. In this case dw_mmc reports "All
phases bad!"). Note that I don't get 100% failure, presumably because
sometimes the card itself has already transitioned away from the AOS
itself by the time we try to wake it up. If I force retuning when "on
= 0" (AKA force retuning right before sending the command to go to
sleep) then retuning is always OK.
NOTE: we need _both_ this patch and the patch to avoid triggering
tuning due to CRC errors in the sleep/wake transition, AKA ("brcmfmac:
sdio: Disable auto-tuning around commands expected to fail"). Though
both patches handle issues with Broadcom's AOS, the problems are
distinct:
1. We want to defer (but not ignore) asynchronous (like
timer-requested) tuning requests till the card is awake. However,
we want to ignore CRC errors during the transition, we don't want
to queue deferred tuning request.
2. You could imagine that the AOS could implement retuning but we
could still get errors while transitioning in and out of the AOS.
Similarly you could imagine a seamless transition into and out of
the AOS (with no CRC errors) even if the AOS couldn't handle
tuning.
ALSO NOTE: presumably there is never a desperate need to retune in
order to wake up the card, since doing so is impossible. Luckily the
only way the card can get into sleep state is if we had a good enough
tuning to send it the command to put it into sleep, so presumably that
"good enough" tuning is enough to wake us up, at least with a few
retries.
Cc: stable@vger.kernel.org #v4.18+
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Reviewed-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Acked-by: Kalle Valo <kvalo@codeaurora.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
There are certain cases, notably when transitioning between sleep and
active state, when Broadcom SDIO WiFi cards will produce errors on the
SDIO bus. This is evident from the source code where you can see that
we try commands in a loop until we either get success or we've tried
too many times. The comment in the code reinforces this by saying
"just one write attempt may fail"
Unfortunately these failures sometimes end up causing an "-EILSEQ"
back to the core which triggers a retuning of the SDIO card and that
blocks all traffic to the card until it's done.
Let's disable retuning around the commands we expect might fail.
Cc: stable@vger.kernel.org #v4.18+
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Reviewed-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Acked-by: Kalle Valo <kvalo@codeaurora.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
This reverts commit 29f6589140.
After that patch landed I find that my kernel log on
rk3288-veyron-minnie and rk3288-veyron-speedy is filled with:
brcmfmac: brcmf_sdio_bus_sleep: error while changing bus sleep state -110
This seems to happen every time the Broadcom WiFi transitions out of
sleep mode. Reverting the commit fixes the problem for me, so that's
what this patch does.
Note that, in general, the justification in the original commit seemed
a little weak. It looked like someone was testing on a SD card
controller that would sometimes die if there were CRC errors on the
bus. This used to happen back in early days of dw_mmc (the controller
on my boards), but we fixed it. Disabling a feature on all boards
just because one SD card controller is broken seems bad.
Fixes: 29f6589140 ("brcmfmac: disable command decode in sdio_aos")
Cc: Wright Feng <wright.feng@cypress.com>
Cc: Double Lo <double.lo@cypress.com>
Cc: Madhan Mohan R <madhanmohan.r@cypress.com>
Cc: Chi-Hsien Lin <chi-hsien.lin@cypress.com>
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Cc: stable@vger.kernel.org
Acked-by: Kalle Valo <kvalo@codeaurora.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
